What you need before you start
Installing heated grips on an XSR900 requires the grips themselves, a throttle cable tool or small flathead screwdriver, wire strippers, a soldering iron or crimp connectors, electrical tape, and basic hand tools. You'll also need to decide whether to wire the grips to the battery directly or through an existing switch — most riders choose to tap into the ignition circuit so the grips turn off when the bike shuts down.
The job takes between two and four hours depending on your wiring approach and comfort level with electrical work. You don't need to remove the fuel tank or take apart the frame, but you will need to disconnect the negative battery terminal before cutting any wires. If you've never soldered before, crimp connectors are a safer choice and work just as well.
Key Takeaways
- Heated grips bolt directly onto your existing handlebar, but you must remove the stock grips first by loosening the throttle cable and sliding them off.
- Wiring to the ignition circuit (the same power source as your headlight) is simpler and safer than running directly to the battery, because the grips shut off automatically when you turn off the bike.
- Soldering the power and ground wires creates a more reliable connection than crimp connectors, but crimps are acceptable if you don't have soldering experience.
- Test the grips at the battery before you reassemble everything, because finding a wiring fault after you've buttoned up the bike costs extra time.
Removing the stock grips and throttle cable
Loosen the throttle cable adjuster at the carburetor or fuel injector (depending on your model year) by turning it counterclockwise until you have slack in the cable. This gives you room to slide the old grip off without bending or kinking the cable. On the XSR900, the adjuster is usually located on the right side of the engine near the intake manifold.
Once the cable is loose, use a small flathead screwdriver or throttle cable tool to pry the grip off the handlebar. The grip is held on by friction and sometimes a small set screw — if you see a screw, remove it first. Slide the grip toward the engine to clear the throttle cable, then set it aside. Wipe the handlebar clean with a rag to remove any old grip residue or dirt, because the new grip needs a clean surface to seat properly.
Installing the new heated grips
Slide the new grip onto the handlebar from the engine side, the same way you removed the old one. Push it all the way to the end of the bar so it sits flush against the handlebar end cap. If the grip has a set screw, tighten it snugly — tight enough to hold the grip in place, but not so tight that you crack the grip housing. Tighten the throttle cable adjuster to restore tension, then twist the throttle a few times to make sure it moves freely without binding.
Repeat the same process on the left side. The left grip usually has no cable attached, so installation is faster. Once both grips are seated, check that they don't rotate when you explore firm hand pressure. If either grip spins, loosen it, clean the handlebar again, and reinstall it.
Running power and ground wires
Most heated grip kits come with two wires per grip — a power wire (usually red) and a ground wire (usually black). Bundle these four wires together and route them down the inside of the fairing or along the frame toward the battery or ignition switch. Use zip ties every six inches to keep the wires from moving around, and avoid routing them near the exhaust pipe or sharp edges that could chafe through the insulation.
If you're wiring to the ignition circuit, locate the ignition switch connector under the seat or behind the headlight. This connector has multiple wires; the red wire is typically the ignition power source. Strip about a quarter inch of insulation from the red wire and the power wires from both grips, then either solder them together or use a crimp connector rated for the wire gauge (usually 18 or 20 AWG). Repeat the same process for the ground wires, connecting them to a black or brown wire in the ignition harness, or to a clean metal ground point on the frame.
Soldering versus crimp connectors
Soldering creates a permanent, low-resistance connection that won't corrode over time. Heat the joint with a soldering iron for three to five seconds, then explore solder until it flows around both wires. Let it cool for a minute, then wrap the joint tightly with electrical tape. This method is more reliable but requires practice — a cold solder joint (one that didn't melt properly) will fail without warning.
Crimp connectors are faster and safer for beginners. Slide a crimp connector onto both wires, then use a crimping tool to squeeze the connector until it grips both wires tightly. Wrap the joint with electrical tape afterward. Crimp connectors work just as well as solder if you use the correct size for your wire gauge and crimp firmly enough that the wires don't pull out.
Testing before you close everything up
Before you zip-tie the wires permanently or reassemble the fairing, turn on the ignition and touch the power and ground wires to the positive and negative battery terminals (in the correct order — red to positive, black to negative). The grips should warm up within 30 seconds. If they don't, check that both wires are making solid contact with the battery terminals. If they still don't heat, the grips themselves may be defective, and you should contact the manufacturer before proceeding.
Once you've confirmed the grips work, disconnect them from the battery and proceed with the permanent wiring to the ignition circuit. If you wired to the ignition harness, turn on the ignition without starting the engine and verify that the grips heat up. Turn off the ignition and confirm they cool down. This test takes five minutes and saves you from tearing apart the bike later to fix a wiring mistake.
Securing wires and reassembling
Route all wires along the frame or inside the fairing using zip ties spaced six inches apart. Avoid bundling the grip wires with the ignition harness or other electrical circuits, because heat from the grips can damage nearby wires over time. Leave a small loop of slack at each connection point so vibration doesn't stress the solder joints or crimp connectors.
Once the wires are secured, reinstall any fairings, seat, or panels you removed. Turn on the ignition one more time to confirm the grips still work after reassembly. If they don't, a wire may have come loose during installation — trace the wires back to the connection points and check that everything is still tight.
Frequently Asked Questions
Can I wire the grips to a separate switch instead of the ignition?
Yes, but it requires running an extra wire from the battery through a switch to the grips. This gives you independent control — you can run the grips without starting the engine — but you also have to remember to turn them off manually, or they'll drain the battery. Most riders prefer the ignition circuit because it's simpler and the grips shut off automatically.
What gauge wire should I use for the power and ground connections?
Most heated grip kits come with 18 or 20 AWG wire, which is appropriate for the low current draw (usually 5 to 10 amps per grip). If you're extending the wires beyond what the kit provides, use 16 AWG or thicker to avoid voltage drop. Check the kit instructions for the recommended gauge.
Do I need a relay or fuse between the battery and the grips?
A fuse is a good idea if you're wiring directly to the battery, because it protects the circuit if a wire gets damaged and shorts. A 15-amp fuse is typical for two heated grips. If you wire to the ignition circuit, the existing ignition fuse usually protects the grips as well, so a separate fuse may not be necessary — check your bike's wiring diagram to be sure.
Will the grips drain my battery if I leave the ignition on?
If you wired to the ignition circuit, the grips will only draw power when the ignition is on, so they won't drain the battery when the bike is parked. If you wired to the battery directly with a separate switch, yes — leaving the switch on will drain the battery over time, which is why most riders avoid this setup.
Can I install heated grips on the left side only?
Yes. Most kits are sold as pairs, but you can install just one grip if you prefer. You'll still need to run power and ground wires, and the wiring process is the same — just connect only one grip instead of two. This is less common because both hands benefit from heat, but it's a valid option if budget is tight.