A tyre change tool is the equipment that removes and installs your wheel — the most basic being a lug wrench and a jack, though the specific tools depend on your car's design

When you get a puncture or need to rotate your tyres, you are removing the wheel from the hub. That wheel is held on by between four and ten lug nuts (the fasteners that screw onto the wheel studs). A lug wrench — a metal tool with sockets on each end — loosens and tightens those nuts. A jack lifts the car high enough to clear the ground. Together, these two tools let you do the job yourself. Without them, you cannot safely remove the wheel at all.

The reason this matters is not just convenience. If you break down on the road and do not have a working jack and wrench, you are stranded until roadside information arrives. If you do have them but they do not fit your car's lug nuts or are too weak to lift your vehicle, you still cannot change the tyre. Knowing what tools you have, whether they work, and how to use them can mean the difference between a 20-minute roadside repair and hours waiting for a tow truck.

Key Takeaways

  • Every car comes with a lug wrench and scissor jack in the boot, but these are minimum-spec tools designed for emergency use, not regular maintenance.
  • The lug wrench must fit your specific lug nut size — most cars use 17mm or 19mm, but some use 21mm or 23mm, and the wrong size will strip the nut.
  • A scissor jack is slow and unstable on soft ground; a hydraulic floor jack is safer and faster if you change tyres regularly or work on uneven surfaces.
  • You also need jack stands to support the car while you work — never work under a car supported only by a jack, as jack failure can cause serious injury.
  • Impact wrenches and torque wrenches are optional but useful: an impact wrench removes stuck lug nuts quickly, and a torque wrench ensures nuts are tightened to the manufacturer's specification.

What comes in your car and what its limits are

Your car's boot contains a lug wrench and a scissor jack as standard. The lug wrench is usually a cross-shaped tool with four different socket sizes, one on each end of each arm. The scissor jack is a diamond-shaped metal device that compresses and extends as you turn a screw handle, lifting the car a few inches at a time. These tools are legal to carry and will work in an emergency, but they have real constraints.

The scissor jack is slow — it takes 30 to 60 turns of the handle to lift a corner of the car fully. It is also unstable on soft ground like grass, gravel, or mud, because the base can sink or slip. On a slope, it can tip sideways. The lug wrench that comes with your car is usually stamped steel, not forged, which means it can bend or crack if you explore too much force — and if you are stuck on the roadside with a corroded lug nut, you will be tempted to explore a lot of force. Neither tool is designed for comfort or speed; they are designed to be small enough to fit in your boot and light enough that you can carry them.

Choosing the right lug wrench for your car

The lug wrench must fit your lug nuts. Most cars use either 17mm or 19mm sockets, but some use 21mm or 23mm. If the wrench does not fit, you cannot turn the nut — and if you force a slightly-too-small wrench onto a nut, you will round off the corners of the nut, making it impossible to remove without cutting it off. Check your owner's manual or look at the lug nuts on your car now to find out which size you need.

Once you know the size, you have two main options. A cross wrench (the standard four-socket design) is cheap, light, and fits in your boot. A single-socket wrench is longer and gives you more leverage, making it easier to break loose a stuck nut. Some people carry both. If you do a lot of tyre work or live somewhere with harsh winters where lug nuts corrode, a single-socket wrench in your size is worth the small extra cost — it can save you from straining your back or damaging the nut.

Jacks: scissor, hydraulic, and when to use each

A scissor jack is what comes with your car. A hydraulic floor jack is a different tool altogether: it has a pump handle you push down repeatedly, and it lifts much faster and higher. A floor jack can usually lift a corner of the car in 5 to 10 pumps instead of 30 to 60 turns of a scissor jack handle. It is also more stable on soft ground because the base is wider and the lifting point is lower.

The trade-off is that a floor jack is heavier (usually 30 to 50 kg), takes up more space, and costs more. If you change your own tyres regularly, rotate them yourself, or live somewhere with soft ground or winter conditions, a floor jack is worth owning. If you change a tyre once every few years on a paved road, the scissor jack that came with your car will do the job. Hydraulic jacks come in different weight ratings — make sure you buy one rated for at least the weight of your car. Check your owner's manual or the door jamb for your car's kerb weight.

Jack stands are not optional safety equipment

A jack lifts your car, but it should never be the only thing holding it up while you work. A jack stand is a metal post with a flat top that sits under the car's frame and holds it at a fixed height. You place the stand under the car, lower the car onto it so the stand takes the weight, and then use the jack to lift the car a bit higher so you can remove the wheel. If the jack fails — and jacks do fail — the stand catches the car and prevents it from falling on you.

Jack stands come in pairs and in different weight ratings. Buy a pair rated for at least your car's kerb weight, and always use both. Place them on a level, hard surface (not grass or gravel), and position them under the car's frame rails or suspension points, not under the body panels. Never work under a car supported only by a jack. This is not a cost-saving measure; it is the difference between a minor incident and a fatal one.

Impact wrenches and torque wrenches: when they matter

An impact wrench is a powered tool that delivers rapid rotational force, usually powered by compressed air or electricity. It removes stuck lug nuts in seconds instead of minutes. If you live in a wet or salty climate where lug nuts corrode, or if you have had a tyre fitted at a garage and the nuts were over-tightened, an impact wrench can save you a lot of frustration. Cordless electric impact wrenches are now affordable and do not require an air compressor.

A torque wrench is a hand tool that tightens a bolt to a specific force, measured in Newton-metres (Nm). Your car's manufacturer specifies the correct torque for your lug nuts — usually between 80 and 130 Nm depending on the car. A torque wrench ensures you tighten the nuts evenly and to the right specification. Over-tightening can strip the studs or warp the brake rotor; under-tightening can allow the wheel to come loose. If you change your own tyres regularly, a torque wrench is worth owning. If you take your car to a garage, they have one and will use it.

Storing and maintaining your tyre change tools

Keep your lug wrench and jack in your car at all times — in the boot or under a seat. Check them every six months to make sure they are still there and still work. If you own a floor jack or jack stands, store them in a dry place like a garage or shed, not outside where they can rust. Wipe down metal tools with a dry cloth after use, especially if you have used them in wet conditions.

Before you need to use your tools in an emergency, practise using them at home on level ground with the car parked safely. Loosen and tighten each lug nut, lift the car with the jack, and place the jack stands underneath. This takes 15 minutes and means you will not be learning the process for the first time on the side of a motorway in the dark.

Frequently Asked Questions

Can I use my car's scissor jack on gravel or grass?

Not safely. The base will sink or slip, and the jack can tip sideways. If you must change a tyre on soft ground, place a flat board or piece of wood under the jack base to spread the weight. Even then, a floor jack is more stable. Never rely on a scissor jack on a slope.

What if the lug wrench that came with my car does not fit?

The socket is the wrong size for your lug nuts. Check your owner's manual to find the correct size, then buy a wrench that fits. Do not force a wrench that does not fit — you will round off the nut and make it impossible to remove without cutting it off.

Do I need a torque wrench if I change my own tyres?

If you change tyres once or twice a year, a torque wrench is useful but not essential — you can tighten the nuts firmly by hand and they will be close enough. If you change tyres regularly or want to be certain you are meeting the manufacturer's specification, a torque wrench costs £20 to £50 and takes the guesswork out.

Can I use a single jack stand instead of a pair?

No. Always use a pair, one on each side of the car under the frame. A single stand leaves the car unbalanced and at risk if it shifts. Buy stands in pairs and use both every time.

What is the difference between a floor jack and a bottle jack?

A floor jack has a wide base and a pump handle; a bottle jack is smaller and cylindrical. Both work, but a floor jack is more stable and lifts faster. A bottle jack is lighter and takes up less space, so some people keep one as a backup. For regular use, a floor jack is the better choice.