A tire monitor fault warning means your car's tire pressure monitoring system (TPMS) has detected a problem with itself, not necessarily with your tires
When you see a tire pressure warning light on your dashboard—often a picture of a tire with an exclamation mark—it can mean one of two things. Either one or more of your tires is actually low on pressure, or the system that measures tire pressure has malfunctioned. A tire monitor fault is the second scenario: the sensors or the receiver that talks to them have stopped working properly, so your car cannot tell you whether your tires are safe or not.
This is different from a straightforward low-pressure warning. When a tire is genuinely underinflated, the light comes on because the sensor detected real pressure loss. When you have a monitor fault, the light comes on because the system itself is broken. You still need to address it, but the fix is different, and the safety concern is different too.
Key Takeaways
- A tire monitor fault means the TPMS sensors or receiver are not working, not that your tires are flat or low.
- Check your tire pressures manually with a gauge at a gas station or tire shop, because your car cannot tell you if they are safe.
- TPMS sensors fail most often because the battery inside them has died, which happens after five to ten years of use.
- A faulty receiver module is less common but more expensive to replace than a single sensor.
- Driving with a monitor fault is not when ready dangerous if your tires are actually at the correct pressure, but you lose the warning system that would alert you to a slow leak.
How the tire pressure monitoring system works
Your car has four sensors—one in each tire—that measure air pressure and send that information wirelessly to a receiver module, usually mounted near the engine or inside the dashboard. Each sensor contains a small battery, a pressure-measuring chip, and a radio transmitter. When you start the car, the receiver listens for signals from all four sensors. If all four report pressures within the safe range, nothing happens. If one tire is low, the light comes on.
A monitor fault occurs when the receiver stops hearing from one or more sensors, or when it receives garbled data it cannot interpret. This can happen because a sensor battery has died, because a sensor has been physically damaged, because the receiver itself has failed, or because there is interference blocking the wireless signal. The car cannot distinguish between these causes, so it straightforward tells you the system is broken.
Why TPMS sensors fail
The most common reason for a tire monitor fault is a dead sensor battery. Each TPMS sensor contains a non-replaceable lithium battery designed to last five to ten years. Once that battery is depleted, the sensor stops transmitting, and your car's receiver has no way to hear from that tire. You cannot replace just the battery—you have to replace the entire sensor.
Sensors can also fail if they are damaged during a tire change or wheel removal. A technician who is careless with the sensor when removing or installing a tire can crack the sensor housing or break the valve stem it is attached to. Corrosion inside the sensor can also occur if moisture gets inside, though this is less common. Road salt, potholes, and curb strikes can physically damage sensors mounted on the wheel rim.
Less often, the receiver module itself fails. This is usually an electrical problem inside the module—a failed component on the circuit board or a loose connection. When the receiver fails, none of your sensors will be heard, so you may see a fault warning even if all four sensors are working fine.
What to do when you see a tire monitor fault light
First, check your tire pressures manually. Use a tire pressure gauge at a gas station, a tire shop, or at home if you own a gauge. Write down the pressure in each tire and compare it to the recommended pressure listed on a sticker inside your driver's door jamb or in your owner's manual. If all four tires are at or near the correct pressure, your tires are safe to drive on—the problem is with the monitoring system, not the tires themselves.
If one or more tires are actually low, inflate them to the correct pressure and see whether the light goes away. Sometimes a low tire will trigger the warning, and once you add air, both the pressure and the warning resolve. If the light stays on after you have confirmed all tires are at the right pressure, you have a genuine monitor fault.
Do not ignore a persistent monitor fault. While your tires may be fine right now, you have lost the early-warning system that would alert you to a slow leak. A tire can lose pressure gradually over weeks or months without you noticing, and by the time you realize it is flat, the tire may be damaged beyond repair. Schedule an appointment with a tire shop or your car's dealership to have the system diagnosed.
Diagnosing which part has failed
A technician will use a TPMS diagnostic tool to check whether each sensor is transmitting and whether the receiver is listening. This tool can tell whether a specific sensor is dead, whether a sensor is transmitting but the receiver is not hearing it, or whether the receiver itself is not working. The diagnostic usually takes 15 to 30 minutes and costs between $50 and $100, though some shops include it free if you are having the fault repaired there.
If one sensor has failed, the shop will replace that sensor. If multiple sensors have failed, they may all need replacement—this can happen if your car is older and several sensors have reached the end of their battery life around the same time. If the receiver module has failed, the shop will replace that module instead. Receiver replacement is less common but more expensive, often running $300 to $500 in parts and labor, compared to $150 to $250 per sensor.
Sensor replacement and what it costs
When a tire shop replaces a TPMS sensor, they remove the tire from the wheel, take off the old sensor, install a new one, and reinstall the tire. The new sensor comes pre-programmed to work with your car's receiver, or the technician will program it during installation. The cost of a replacement sensor varies by vehicle make and model—some sensors are $40 to $80, while others can be $150 or more. Labor usually adds another $50 to $100 per sensor.
Some shops sell aftermarket sensors, which are cheaper than original equipment manufacturer (OEM) sensors but may not last as long or work as reliably. If you are having a sensor replaced, ask whether the shop is using OEM or aftermarket parts, and ask about the warranty on the replacement. A reputable shop will may provide the sensor for at least one year.
If you are having your tires replaced anyway—because they are worn out or damaged—this is a good time to replace a faulty sensor, because the tire shop is already removing the wheel. The labor cost does not increase much when sensor replacement is bundled with a tire change.
Driving with a tire monitor fault
If your tires are at the correct pressure and you have confirmed this with a manual gauge, it is safe to drive with a monitor fault in the short term. The fault does not affect your car's ability to stop, steer, or accelerate. However, you are now driving without an early-warning system. If a tire develops a slow leak, you will not know about it until the tire is dangerously low or flat.
For this reason, you should check your tire pressures manually every two to four weeks while the monitor is broken. This takes five minutes and costs nothing. Use the same gauge and the same time of day each time—tire pressure changes with temperature, so checking in the morning gives you a consistent baseline. If you notice pressure dropping in one tire, you may have a leak that needs repair.
Do not drive on a highway for long distances with a known monitor fault unless you have very recently confirmed that all tires are at the correct pressure. A slow leak can develop during a long drive, and without the warning system, you might not notice until the tire fails.
Frequently Asked Questions
Can I drive without fixing the tire monitor fault?
Yes, if your tires are actually at the correct pressure. Check them manually with a gauge first. You lose the warning system that would alert you to a leak, so you should check pressures every few weeks. For long highway drives, confirm tire pressure right before you leave.
Will the light go away on its own?
No. A monitor fault means a sensor battery is dead or a component has failed. These do not repair themselves. The light will stay on until you replace the faulty sensor or receiver module. Some cars will eventually stop showing the light if the receiver gives up trying to hear from a dead sensor, but the system is still broken.
Is it cheaper to replace all four sensors at once or just the bad one?
If only one sensor has failed, replacing just that one is cheaper. However, if your car is ten or more years old, the other three sensors may fail soon after. Ask the technician whether the other sensors are showing signs of age. If they are, replacing all four at once may cost less in total labor than replacing them one at a time over the next year.
What if the receiver module is broken instead of a sensor?
A technician can diagnose this with a TPMS tool. Receiver replacement is more expensive than sensor replacement—usually $300 to $500—but it is the only fix if the receiver has failed. The good news is that receiver failure is less common than sensor failure.
Can I ignore the fault light if I check my tires regularly?
You can drive safely in the short term if you check pressures manually every few weeks. However, the system is still broken, and you should have it repaired. A slow leak can develop faster than you check, and the warning light exists to catch problems you might miss. Repair it when your schedule allows.