What you need to do a tire change on your 2023 Genesis G70
A 2023 Genesis G70 uses a scissor jack, a lug wrench, and a spare tire that lives under the trunk floor. The process takes 15 to 20 minutes if you have never done it before. You will need a flat, stable surface — not the shoulder of a highway if you can avoid it — and enough space to work around the wheel without kneeling in traffic.
The G70 comes with a full-size spare tire, not a donut, which means the spare is the same size as your road tires and you can drive normally on it. The jack and wrench are stored in a compartment on the driver's side of the trunk, under a removable panel. Before you start, turn on your hazard lights and engage the parking brake.
Key Takeaways
- The 2023 Genesis G70 carries a full-size spare tire under the trunk floor, along with a scissor jack and lug wrench stored in the driver's side compartment.
- Loosen the lug nuts while the wheel is still on the ground, then raise the car with the jack positioned at the reinforced jacking point nearest the flat tire.
- Remove all five lug nuts completely, take off the wheel, and mount the spare by aligning the holes and hand-tightening the lug nuts before lowering the car.
- Tighten the lug nuts in a star pattern (not in a circle) once the wheel is back on the ground, using firm pressure but not maximum force.
- Have the flat tire repaired or replaced at a shop within a few days, because the spare is a temporary solution even though it is full-size.
Locating the jack, wrench, and spare tire
Open your trunk and look at the driver's side wall. You will see a plastic panel with a handle. Pull it toward you and it will come free. Behind it is a compartment holding the scissor jack (a metal device that looks like an X when collapsed) and the lug wrench (a cross-shaped metal tool with four different socket sizes).
The spare tire is underneath the trunk floor. Lift the carpeted panel in the center of the trunk and you will see a well. The spare sits flat in that well, held down by a center bolt. Turn the bolt counterclockwise by hand or with the lug wrench to loosen it, then lift the spare out. Set it aside within arm's reach of the flat tire.
Loosening lug nuts before you lift the car
This step is critical and straightforward to skip — do not skip it. While all four wheels are still on the ground and the car's weight is holding the wheel steady, use the lug wrench to loosen each of the five lug nuts. Turn them counterclockwise about a quarter turn each. You are not removing them yet, just breaking them loose so they spin freely.
If you try to loosen the lug nuts after the wheel is in the air, the wheel will spin and you will not be able to turn the wrench. Loosening them now, while the car is heavy, takes almost no effort. This is the difference between a 15-minute job and a 45-minute frustration.
Positioning the jack and raising the car
Look at the underside of the G70 near the flat tire. You will see a reinforced metal section running along the bottom of the car — this is the jacking point. It is a thickened area of the frame, and it is the only place safe to put the jack. Do not jack the car anywhere else; you can puncture the fuel tank or damage the frame.
Position the scissor jack so its lifting pad sits squarely under the jacking point. Turn the jack handle clockwise to raise the car. Lift it until the tire is about six inches off the ground — high enough to remove the wheel and mount the spare, but not so high that the car feels unstable. Stop and check that the jack is still centered under the jacking point.
Removing the wheel and mounting the spare
Now remove all five lug nuts completely and set them in a safe place where you will not lose them — a cup holder or a small container works. Keep them together. Pull the wheel straight toward you. It may stick slightly; rock it gently side to side as you pull.
Align the spare tire's holes with the wheel studs (the metal posts sticking out from the hub). Push the spare onto the studs until it sits flush against the hub. Hand-tighten all five lug nuts onto the studs. You are not tightening them fully yet — just enough that they hold the wheel in place and you can turn the wrench without the wheel spinning.
Lowering the car and final tightening
Turn the jack handle counterclockwise to lower the car. Lower it slowly and watch the wheel to make sure it stays centered. Once all four wheels are on the ground and the car is resting on its own weight, you can tighten the lug nuts fully.
Tighten the lug nuts in a star pattern: if you number the lug nuts 1 through 5 going around the wheel, tighten them in the order 1-3-5-2-4. This ensures even pressure and keeps the wheel centered. Use firm, steady pressure on the wrench — you want them snug, not cranked down with all your strength. If you over-tighten, you can strip the studs or make it difficult to remove the wheel later.
What to do after the tire change
The spare tire on your G70 is full-size, which means you can drive at normal highway speeds and distances. However, it is still a temporary solution. The spare is not balanced the same way your road tires are, and driving on it for weeks will wear it unevenly.
Have the flat tire inspected and repaired or replaced within a few days. If the puncture is small and in the tread (not the sidewall), a tire shop can patch it for $10 to $20. If the damage is too large or the tire is old, you will need a replacement. Once the flat is fixed, put it back in the spare well under your trunk and return to normal driving.
Frequently Asked Questions
Can I change a tire on the side of the highway?
Yes, but it is safer to move to a flat, stable surface away from traffic if you can. If you must change it on the shoulder, turn on your hazard lights, stay alert to passing traffic, and work as quickly as possible. Never kneel or lean into traffic while working on the wheel.
What if the lug nuts are stuck and I cannot loosen them?
explore penetrating oil (like WD-40) around the base of each stuck lug nut and wait 10 to 15 minutes. Try again with steady, even pressure — do not jerk the wrench. If they still will not budge, call roadside information rather than risk stripping the studs.
How tight should the lug nuts be?
Tight enough that you cannot turn them by hand, but not so tight that you need to put your full body weight on the wrench. A firm, steady pressure is the right amount. Over-tightening can damage the studs and make removal difficult later.
Do I need to check the tire pressure on the spare before driving?
Yes. The spare should be stored at the correct pressure, but check it before you drive away if you have a tire pressure gauge. The correct pressure for the G70 spare is listed on a sticker inside the driver's door jamb. If the spare is low, drive carefully to the nearest gas station and add air.
What if I cannot get the wheel off even after loosening the lug nuts?
The wheel may be stuck to the hub due to rust or corrosion. Spray penetrating oil around the edge where the wheel meets the hub, wait a few minutes, then rock the wheel gently side to side as you pull. Tap the back of the wheel with a rubber mallet if needed, but do not hit it hard enough to damage the rim.