A jack lifts your car high enough to remove a wheel, but it only works if you position it correctly and use it on stable ground

A jack is a mechanical device that raises one corner of your car by converting downward force (usually from a handle you pump or turn) into upward lift. Most cars come with a scissor jack—a flat, diamond-shaped tool that fits into a notch on the frame near each wheel. The jack itself does not remove the tire; it straightforward holds the car high enough so you can unscrew the lug nuts and pull the wheel off.

The most common mistake is placing the jack on soft ground, under the wrong part of the frame, or without first loosening the lug nuts. Any of these will either prevent the jack from working or create a dangerous situation where the car could slip or fall. Before you touch the jack, you need to be parked on level, solid ground and have already broken the lug nuts loose by hand.

Key Takeaways

  • Park on level, hard ground away from traffic, and loosen all lug nuts by hand before you lift the car.
  • Locate the frame notch nearest the flat tire—it is usually a small indentation on the rocker panel below the door—and position the jack's saddle directly under it.
  • Pump or turn the jack handle slowly and steadily until the tire clears the ground by about six inches, then remove the lug nuts and wheel.
  • Lower the jack only after the new tire is bolted back on and all lug nuts are hand-tight, then finish tightening them once the car is on the ground.
  • Never crawl under a car supported only by a jack; use jack stands if you need to work underneath.

Finding the correct lift point on your car's frame

Every car has reinforced points on the frame where a jack can safely support its weight. These are not random—they are built into the structure specifically for this purpose. On most vehicles, the lift points are located on the rocker panel (the body panel between the front and rear wheels, below the doors). You will see a small notch or indentation in this panel, usually about the size of a quarter.

Your owner's manual shows exactly where these points are for your specific car. If you do not have the manual, look inside the driver's door jamb or the fuel door—many cars have a diagram printed there. The notch is designed so the jack's saddle (the flat top part that touches the car) sits flush against the frame. If you place the jack anywhere else—under the bumper, the door, the transmission pan, or the plastic trim—you risk puncturing the fuel tank, damaging the undercarriage, or having the car slip off the jack.

Preparing the car and loosening the lug nuts

Before you raise the car, park on level ground that is solid and dry. Asphalt, concrete, and packed dirt work. Gravel, sand, wet grass, and sloped driveways do not—the jack will sink or tip. Turn off the engine, engage the parking brake, and turn on your hazard lights if you are on a road.

Now loosen the lug nuts while the tire is still on the ground. This is the single most important step. Once the car is in the air, the wheel will spin freely and you will not be able to turn the nuts. Use the lug wrench (the cross-shaped tool that came with your car) and turn each nut counterclockwise about a quarter turn—just enough to break the seal. You do not need to remove them yet; you just need to know they will come loose. If a nut is stuck, do not force it; you may need penetrating oil or a longer wrench for leverage.

Raising the car with the jack

Position the jack so its saddle aligns perfectly with the frame notch. The saddle should sit flat against the frame with no gaps or tilting. If the ground is slightly uneven, place a small, flat board under the jack base to distribute the weight and prevent sinking.

Begin pumping or turning the jack handle slowly and steadily. Watch the car rise and listen for any creaking or grinding sounds—these are warning signs that something is wrong. Stop when ready if you hear them. Raise the car until the flat tire is about six inches off the ground. You need enough clearance to remove the wheel and slide the new one on, but you do not need to raise it higher; higher means less stable.

Once the car is at height, finish removing the lug nuts by hand and set them in a safe place where they will not roll away. Pull the wheel straight toward you to remove it from the hub.

Installing the new tire and lowering the car

Align the holes on the new tire with the studs (the bolts sticking out from the hub) and push the wheel on. It should slide on smoothly; if it does not, the holes may not be aligned. Rotate it slightly and try again. Once the wheel is seated, thread the lug nuts back on by hand and tighten them snugly—not with all your strength, just hand-tight.

Now lower the car by turning the jack handle in the opposite direction. Lower it slowly and watch to make sure the wheel stays centered on the hub. Once the tire is fully on the ground and the car's weight is resting on it, you can remove the jack.

Use the lug wrench to tighten the lug nuts fully in a star or cross pattern (tighten one, skip one, tighten the next, and so on). This ensures even pressure around the wheel. Tighten them firmly but do not overtighten—you are not trying to weld them on. If you have a torque wrench and know your car's lug nut torque specification (usually 80 to 120 foot-pounds, depending on the vehicle), use it for accuracy.

Why jack placement and ground stability matter for safety

A car weighs between 2,500 and 4,500 pounds depending on the model. A scissor jack typically lifts 1.5 to 2 tons, which is enough—but only if the weight is distributed correctly and the ground does not give way. If the jack is placed even slightly off the frame notch, the saddle can slip sideways and the car can fall. If the ground is soft, the jack base sinks and tilts, and again the car falls.

A falling car can crush your hand, foot, or leg in seconds. It can also damage the car's frame beyond repair. This is not a theoretical risk; it happens regularly to people who skip the preparation steps or rush through them. Taking an extra two minutes to find the right spot and test the ground is the difference between a safe tire change and a trip to the emergency room.

When to use jack stands instead of relying on the jack alone

A jack is designed to lift the car, not to hold it in place for extended work. If you need to do anything under the car—inspect the brake line, look at the suspension, or work on anything other than the wheel itself—you must use jack stands. These are metal stands with a flat top that support the car's weight independently of the jack.

The correct procedure is to lift the car with the jack, place a jack stand under the frame notch, lower the car onto the stand, and then remove the jack. Never work under a car supported only by a jack. Never use cinder blocks, wood, or improvised supports instead of proper jack stands. If the stand fails or shifts, the car will fall.

Frequently Asked Questions

Can I use a floor jack instead of the scissor jack that came with my car?

Yes. A floor jack (the larger hydraulic jack you might borrow or rent) lifts more smoothly and requires less physical effort. Use the same frame notch, and always place a jack stand under the car before working underneath. A floor jack is easier on your back and faster, but it still requires the same safety precautions.

What if the lug nuts are too tight to loosen by hand?

Use a longer wrench or a breaker bar for more leverage. If that does not work, spray the nuts with penetrating oil (like WD-40 or PB Blaster) and wait 10 to 15 minutes for it to soak in. Do not use a hammer to hit the wrench—you risk stripping the nut or breaking the wrench. If the nut still will not budge, you may need a tire shop to remove it.

How do I know if my car is high enough off the ground?

The tire should clear the ground by at least four to six inches. You should be able to slide your hand under the tire without it touching. If you are unsure, raise it a bit more—it is safer to have extra clearance than to have the wheel brush the ground when you are trying to install the new one.

What should I do if the jack starts to slip while the car is in the air?

Stop when ready and lower the car slowly. Do not try to catch it or jump out of the way. Once it is on the ground, check the ground surface (it may be softer than you thought) and the jack placement (it may have shifted). Reposition and try again, or call for roadside help if you are not confident.

Do I need to tighten the lug nuts again after driving?

Yes. After driving 50 to 100 miles on a newly installed wheel, stop and check the lug nuts with a wrench to make sure they are still tight. New wheels can settle slightly, and the nuts may loosen a little. This is a quick check that takes two minutes and prevents the wheel from coming off.