What happens when you change a spare tire
Replacing a spare tire means removing the flat or damaged wheel from your car and putting the spare in its place. You do this with a jack (a device that lifts the car), a lug wrench (a tool that loosens the bolts holding the wheel on), and the spare tire itself. The whole job takes 15 to 30 minutes if you have never done it before, and the spare is in good condition.
A spare tire is not a permanent fix. It is smaller and lighter than your regular tires, and it is designed to get you to a repair shop safely—usually at speeds under 50 mph and for distances under 70 miles. Some spares are full-size wheels that match your other tires; others are compact "donut" spares that take up less trunk space. Either way, you should have the flat tire repaired or replaced as soon as you can, and move the spare back to storage.
Key Takeaways
- You will need the jack, lug wrench, and spare tire that came with your car, plus a flat surface away from traffic.
- Loosen the lug nuts while the wheel is still on the ground, then jack up the car, remove the wheel, and install the spare.
- Tighten the lug nuts by hand first, lower the car, then tighten them fully in a star or cross pattern to avoid warping the wheel.
- Drive to a tire shop within a few days to have the flat repaired or replaced, because a spare tire is not safe for long-term use.
- Check your spare tire's air pressure every few months, because spares lose pressure over time even when not in use.
Gather your tools and find a safe spot
Open your trunk and locate the spare tire, jack, and lug wrench. In most cars, these are stored under the trunk floor or in a compartment on the side. Check your owner's manual if you cannot find them—the manual will show you exactly where they are and how to remove them. Make sure the spare has air in it by pressing on it with your hand; if it feels soft or flat, you may need to inflate it before you can use it safely.
Pull over to a flat, stable surface away from traffic. An empty parking lot, a wide shoulder on a quiet road, or a driveway is ideal. Avoid soft ground like grass or gravel, because the jack can sink and the car can slip. Turn on your hazard lights so other drivers can see you. If you are on a highway, stay as far from the road as possible and consider calling roadside information instead of changing the tire yourself.
Loosen the lug nuts before you jack up the car
The lug nuts are the bolts that hold the wheel on. You must loosen them while the wheel is still on the ground, because once the car is in the air, the wheel will spin freely and you will not be able to turn the nuts. Place the lug wrench on each nut and turn it counterclockwise. You do not need to remove the nuts completely at this stage—just loosen them enough that you can turn them by hand. If a nut is very tight, use your body weight to push down on the wrench handle rather than straining your hands.
Most cars have either four or five lug nuts per wheel. Loosen all of them before moving on. If you cannot loosen a nut, do not force it—stop and call for roadside information, because forcing it can strip the bolt or damage the wheel.
Jack up the car and remove the wheel
Locate the jacking point on your car. This is a reinforced spot on the frame designed to support the jack. Your owner's manual shows you where it is; it is usually a notch or a small metal tab on the side of the car, near the wheel you are changing. Place the jack under this point, not under the bumper or the door, because the car can slip and cause serious injury.
Pump or crank the jack handle to raise the car until the wheel is about six inches off the ground. You should be able to fit your hand under the tire. Once the car is high enough, finish removing the lug nuts by hand and set them in a safe place where you will not lose them—a cup or a small container works well. Grip the wheel with both hands and pull it straight toward you to remove it from the hub.
Install the spare and hand-tighten the lug nuts
Align the holes on the spare tire with the bolts on the hub. This takes a little wiggling, but the holes are designed to fit only one way. Push the spare straight onto the bolts until it sits flush against the hub. Thread the lug nuts back on by hand, turning them clockwise. Tighten them as much as you can with your fingers, but do not use the wrench yet. Hand-tightening prevents you from over-tightening and warping the wheel.
Once all the nuts are hand-tight, lower the car by reversing the jack handle. Lower it slowly and steadily until the spare tire touches the ground and the car's full weight is on it. Then remove the jack completely.
Tighten the lug nuts in the correct pattern
Now use the lug wrench to tighten the lug nuts fully. This is where the pattern matters. If you tighten them in order around the wheel (1, 2, 3, 4, 5), you can pull the wheel off-center and warp it. Instead, use a star or cross pattern: tighten the nut at the top, then the one at the bottom, then the one on the left, then the one on the right, then any remaining nut in the middle. This distributes pressure evenly.
Tighten each nut firmly, but do not over-tighten. You want them snug enough that they will not come loose while you drive, but not so tight that you strip the bolt or make it impossible to remove them later. A good rule: tighten until you feel solid resistance, then give the wrench a quarter-turn more. If you have a torque wrench (a specialized tool that measures tightness), your owner's manual lists the correct torque specification—usually between 80 and 120 foot-pounds, depending on your car.
Drive carefully to a tire shop
You are now safe to drive, but remember that a spare tire is temporary. Keep your speed under 50 mph and drive directly to a tire repair shop. Do not take long trips or drive on the highway. Most tire shops can patch a puncture in 15 to 30 minutes if the damage is in the tread and not near the sidewall. If the puncture is large, the sidewall is damaged, or the tire is old, the shop will recommend replacement.
Once the flat tire is repaired or replaced, ask the shop to reinstall it on your car and move the spare back to storage. Check the spare's air pressure every few months, because spares lose pressure over time even when sitting unused. A flat spare is useless in an emergency.
Frequently Asked Questions
What if I cannot loosen the lug nuts by hand?
Stop and call roadside information. Forcing a stuck nut can strip the bolt or damage the wheel permanently. A professional has tools and experience to remove stuck nuts without causing harm. This is not a situation to push through on your own.
Can I drive long distances on a spare tire?
No. Spare tires are designed for short trips to a repair shop only. Driving more than 70 miles or faster than 50 mph on a spare can overheat it, cause it to fail, and leave you stranded. If you need to travel far, have the flat repaired or replaced before you leave.
Do I need to balance the spare tire after I install it?
No. A spare tire that came with your car is already balanced. You only need balancing if you install a used spare from another car, or if the spare has been sitting for years and the weight has shifted. Your tire shop can balance it if needed.
What should I do if the spare tire is flat?
If the spare has no air, you cannot use it safely. Call roadside information or a tow truck to take you to a tire shop. Do not attempt to drive on a flat spare. Once you reach the shop, they can inflate the spare and repair or replace your original flat tire.
How tight should the lug nuts be?
Tight enough that they will not loosen while you drive, but not so tight that you strip the bolt. Tighten until you feel solid resistance, then give the wrench a quarter-turn more. If your car's manual lists a torque specification, use a torque wrench to match it exactly. Over-tightening is a common mistake that makes removal difficult later.