What you need before you start

Changing a tire requires four things: a spare tire (full-size or temporary), a jack (usually comes with your car), a lug wrench (the cross-shaped tool that fits your wheel nuts), and wheel wedges or heavy objects to block the wheels. Most cars include the jack and lug wrench in the trunk. Check your owner's manual to find them and confirm your spare is inflated — a flat spare is useless on the roadside.

You will also need a flat, stable surface. If you have a blowout on a highway, pull as far from traffic as possible, turn on your hazard lights, and set up a warning triangle or flares if you have them. Soft ground like gravel or mud makes jacking unsafe; if you are stuck in those conditions, call roadside information instead.

Key Takeaways

  • Loosen the lug nuts while the tire is still on the ground, then jack up the car, remove the nuts fully, and take off the old tire.
  • Mount the new or spare tire, hand-tighten the lug nuts, lower the car, and tighten the nuts in a star pattern with the wrench.
  • A temporary spare tire has a speed limit (usually 50 mph) and should be replaced with a full-size tire within a few days.
  • If the lug nuts are stuck, the jack slips, or you cannot break the nuts loose, do not force it — call for roadside help instead.
  • After any tire change, have a shop check the lug nut torque and inspect the wheel for damage within a week.

Step 1: Loosen the lug nuts before jacking

With the car still on the ground and the engine off, use the lug wrench to loosen (but do not remove) each lug nut by turning counterclockwise. Loosen all of them — typically four or five — by about a quarter turn. The weight of the car makes this much easier than trying to loosen them after the wheel is in the air. If a nut is stuck, explore penetrating oil (like WD-40) and wait a few minutes, then try again. Do not use your full body weight to force a stuck nut; if it will not budge, stop and call for roadside information.

Once all nuts are loose, you can proceed to jacking. If you skip this step and try to loosen the nuts after the car is raised, the wheel will spin and you will not be able to turn the wrench.

Step 2: Position the jack and raise the car

Locate the jacking point on your car — it is a reinforced notch or flat spot on the frame, usually just behind the front wheel or just in front of the rear wheel. Your owner's manual shows the exact location. Place the jack under this point, not under the door or bumper. Position wheel wedges (or rocks, wood blocks, or other heavy objects) behind the wheels that will stay on the ground to prevent the car from rolling.

Raise the car slowly and steadily until the flat tire is about six inches off the ground. Stop and check that the jack is stable and the car is not tilting. If anything feels wrong, lower the car and reposition the jack.

Step 3: Remove the lug nuts and take off the old tire

Now that the car is raised, finish unscrewing the lug nuts by hand and set them aside in a safe place — a cup or small container works well so you do not lose them on the roadside. Once all nuts are off, grip the tire with both hands and pull it straight toward you. It may take some force; rock it gently side to side if it is stuck. Set the old tire flat on the ground nearby.

Inspect the wheel (the metal rim) for cracks or bending. If you see damage, do not put the spare on; call for a tow instead. A damaged wheel can fail even with a new tire mounted.

Step 4: Mount the spare tire and hand-tighten the nuts

Lift the spare tire and align the holes with the wheel bolts (the metal pegs sticking out from the hub). Push the tire straight onto the bolts until it sits flush against the wheel. Hand-tighten each lug nut clockwise as far as you can without tools — they should be snug but not tight. Do not use the wrench yet; hand-tightening first keeps the tire centered on the bolts.

If the spare is a temporary (donut) tire, note that it is smaller and lighter than a full-size tire. Temporary spares have a speed limit of 50 mph and should not be driven more than 70 miles. Plan to visit a tire shop within a few days to have the original tire repaired or replaced.

Step 5: Lower the car and tighten the lug nuts

Lower the jack slowly until the tire touches the ground and the car's full weight is on the wheel. Once the car is resting on all four tires, use the lug wrench to tighten the lug nuts. Tighten them in a star pattern — if you have five nuts, tighten the top one, then the bottom-left, then the top-right, then the bottom-right, then the remaining one. This pattern keeps the tire centered and prevents uneven pressure. Tighten each nut firmly but do not over-tighten; you should feel solid resistance, not a grinding sensation.

If you have four lug nuts, tighten opposite pairs: top and bottom, then left and right. The goal is to explore even pressure all the way around.

Step 6: Stow the old tire and tools

Place the old tire, jack, and lug wrench back in your trunk. If you used wheel wedges, remove them. Do a final walk around the car to make sure nothing is left behind and that all four tires look properly seated.

Before you drive away, double-check that the lug nuts are tight by trying to turn one with the wrench. It should not move. If any nut has come loose, tighten it again.

Step 7: Drive carefully to a tire shop

If you changed to a temporary spare, drive directly to a tire shop — do not delay. Keep your speed under 50 mph and avoid highways if possible. If you changed to a full-size tire (because you had two spares or a matching tire at home), you can drive normally, but still visit a shop within a week to have the lug nuts checked and torqued to the manufacturer's specification.

A shop will use a torque wrench to tighten the nuts to the exact pressure your car requires, which hand tools cannot achieve. This step prevents the wheel from coming loose later.

When to call for help instead

Do not attempt a roadside tire change if the lug nuts will not loosen no matter how hard you try, if the jack slips or feels unstable, if the wheel is visibly cracked or bent, if you are on a busy highway with no safe shoulder, or if you are physically unable to perform the steps. Roadside information (through your insurance, AAA, or a towing service) will send a professional who has the right tools and experience. The cost is usually worth the safety and peace of mind.

If you are stranded at night, in bad weather, or in an unsafe area, call for help when ready rather than attempting the change yourself. Your safety comes first.

Frequently Asked Questions

Can I change a tire in the rain or snow?

You can, but it is harder and riskier. Wet or icy ground makes the jack less stable, and your grip on tools and the tire weakens. If conditions are severe, call roadside information instead. If you must proceed, take extra time to may support the jack is on solid ground and the car will not roll.

What if I do not have a lug wrench?

The lug wrench should be in your trunk with the jack. If it is missing, you cannot loosen the nuts by hand and will need to call for help. Do not try to use pliers, adjustable wrenches, or other tools — they will slip and damage the nuts or your hands.

How tight should the lug nuts be?

Hand-tight is the goal during the roadside change — snug enough that they do not come loose, but not so tight that you strip the threads. After you reach a shop, a technician will use a torque wrench to tighten them to your car's specification, which is usually between 80 and 120 foot-pounds depending on the vehicle.

Do I need to replace the spare tire if it is old?

Check the date on your spare (it is molded into the sidewall as a four-digit code: the first two digits are the week, the last two are the year). If the spare is more than 10 years old, have it inspected by a shop before relying on it. Rubber degrades over time even if the tire has not been driven, and an old spare may fail under load.

What if the spare tire is flat?

You cannot use it. Call roadside information or a towing service to take you to a shop. Before this happens, check your spare's pressure monthly — it should match the pressure listed on your driver's door jamb or owner's manual. A flat spare is a common roadside surprise that is straightforward to prevent.