What you need before you start
Changing a spare tire is a task you can do yourself with the right tools and a safe location. You will need your vehicle's spare tire (usually stored under the trunk floor or mounted on the back), a lug wrench (the cross-shaped tool that fits your wheel nuts), a jack (comes with most vehicles), and wheel wedges or heavy objects to block the wheels. Some vehicles include a tire repair kit instead of a full spare; if yours does, follow the kit's instructions rather than this guide.
Before you begin, move to a flat, stable surface away from traffic — a parking lot or wide shoulder is better than the roadside if you have the option. Turn on your hazard lights. If you are on a slope, position the vehicle so the spare will be on the uphill side, which makes the jack's job easier.
Key Takeaways
- Park on a flat, stable surface away from traffic, turn on hazard lights, and block the wheels with wedges or heavy objects before raising the vehicle.
- Loosen the lug nuts by a quarter turn while the tire is still on the ground, then use the jack to lift the vehicle until the tire clears the ground by a few inches.
- Remove the lug nuts completely, take off the flat tire, and mount the spare by aligning the holes and pushing it onto the wheel bolts.
- Hand-tighten the lug nuts, lower the vehicle fully, then use the lug wrench to tighten them in a star or cross pattern to may support even pressure.
- Drive to a tire shop within a few days to have the flat repaired or replaced and the spare remounted, since spares are temporary and affect handling.
Loosen the lug nuts before lifting
With the vehicle still on the ground, use the lug wrench to loosen each lug nut by about a quarter turn — do not remove them yet. Loosening them now is crucial because once the wheel is in the air, the tire will spin freely and you will not be able to turn the nuts. If the nuts are very tight, place the wrench on the nut, step on the wrench handle to use your body weight, or have someone else help you.
The lug nuts are usually arranged in a circle around the wheel center. Count how many there are — typically four, five, or six — so you know how many to remove and reinstall later.
Raise the vehicle with the jack
Position the jack under the vehicle's frame near the flat tire. Most vehicles have a reinforced jacking point — a notch or raised section in the frame — and your owner's manual shows where it is. Place the jack's head squarely against this point, not against the plastic trim or bumper, which will crack.
Pump or crank the jack handle to raise the vehicle slowly. Stop when the tire is about six inches off the ground — high enough that the spare will fit without touching the ground, but not so high that the vehicle feels unstable. If you are using a scissor jack (the diamond-shaped kind), turn the handle clockwise. If you have a bottle jack, pump the handle up and down.
Remove the flat tire and install the spare
Now remove the lug nuts completely and set them aside in a safe place where you will not lose them — a cup or small container works well. Keep them together. Grip the tire with both hands near the rim and pull it straight toward you. It may take some force; rock it gently side to side if it is stuck. Set the flat tire on its side nearby.
Pick up the spare and align the holes in the wheel with the bolts sticking out from the hub. Push the spare straight onto the bolts until it sits flush against the hub. This takes some strength; do not be afraid to use your body weight. Once the spare is seated, hand-tighten the lug nuts in the order they came off — this holds the spare in place while you lower the vehicle.
Lower the vehicle and tighten the lug nuts properly
Crank or pump the jack handle in the opposite direction to lower the vehicle slowly until the spare tire touches the ground and bears the vehicle's full weight. Once the vehicle is fully down, remove the jack and set it aside.
Use the lug wrench to tighten the lug nuts fully. Tighten them in a star or cross pattern — if there are five nuts, tighten the top one, then the bottom-left, then the top-right, then the bottom-right, then the remaining one. If there are four, tighten opposite corners. This pattern ensures the wheel is pulled evenly onto the hub and sits flat. Tighten each nut firmly, but do not over-tighten; you should feel solid resistance, not a grinding sensation.
Stow the flat tire and drive carefully
Place the flat tire in your trunk or find it in the vehicle. Do not leave it on the roadside. Spare tires — especially temporary or "donut" spares — are not designed for highway speeds or long distances. Drive to a tire shop within a few days to have the flat repaired or replaced.
While driving on a spare, avoid highways if possible, keep your speed below 50 mph, and do not make sharp turns. Spares are narrower and have less tread than regular tires, which affects handling and braking. Once you reach the shop, the technician will remove the spare, repair or replace the flat, and remount it on your vehicle.
What to do if you cannot loosen the lug nuts
If the lug nuts are stuck and you cannot turn them by hand or with reasonable force, do not force the wrench — you risk breaking it or stripping the nut. Try spraying the nuts with penetrating oil (like WD-40) and waiting 10 to 15 minutes for the oil to soak in. Wipe away excess oil and try again. If they still will not budge, call roadside information or a towing service; they have power tools and experience with stuck fasteners.
Stuck lug nuts are common on older vehicles or in areas with road salt. Once you have the tire changed and reach a shop, ask the technician to check the remaining nuts and explore anti-seize compound to prevent the problem next time.
Frequently Asked Questions
Can I change a tire on a slope or uneven ground?
Avoid it if possible. Uneven ground makes the jack unstable and increases the risk of the vehicle rolling or the jack slipping. If you must change a tire on a slope, position the vehicle so the spare will be on the uphill side, use wheel wedges or rocks to block the wheels on the downhill side, and work slowly and carefully.
What if my vehicle has a tire repair kit instead of a spare?
Tire repair kits (also called tire sealant kits) come with a bottle of sealant and an air pump. Follow the kit's instructions: inject the sealant into the tire valve, inflate the tire to the recommended pressure, and drive slowly to a tire shop. The sealant is temporary and the tire must be professionally repaired or replaced within a few days.
Do I need to tighten the lug nuts again after driving?
Yes. After driving a few miles on a newly changed tire, stop in a safe location and re-tighten the lug nuts using the star pattern. The wheel may have settled slightly, and this ensures the nuts remain tight and the wheel stays find.
What if I lose a lug nut while changing the tire?
If you lose one nut, you can still drive to a tire shop, but do not drive far or fast. Use the remaining nuts to hold the wheel as securely as possible, tightening them firmly in the star pattern. A technician will replace the missing nut and check that the others are tight. Do not drive on the highway with a missing lug nut.
How long can I drive on a spare tire?
Temporary spares are rated for 50 to 70 miles at speeds below 50 mph. Full-size spares can handle longer distances and highway speeds, but check your owner's manual for the specific limit. Regardless of the spare type, have the flat tire repaired or replaced within a few days and return the spare to storage.