What you need to do before you start

Changing a motorcycle tire is a job you can do yourself if you have the right tools and a safe workspace, but it requires precision and care—a poorly seated tire or an unbalanced wheel will make your bike unsafe to ride. Before you touch anything, gather your tools: a tire iron or spoon set (usually two or three curved metal levers), a bead breaker (a tool that separates the tire from the rim), a motorcycle jack or center stand, a valve stem tool, and a new tire that matches your bike's specifications exactly. Check your owner's manual for the correct tire size, load rating, and speed rating; using the wrong tire can affect handling and braking.

Park your motorcycle on a level, solid surface—concrete is best. If you're working outdoors, avoid soft ground where the jack could sink. Remove the wheel from the bike using the correct socket size for your axle nut; most motorcycles require a 17mm or 19mm socket. Once the wheel is off, deflate the tire completely by removing the valve stem core with a valve stem tool, then set the wheel on a work surface where it won't roll.

Key Takeaways

  • You need a tire iron set, bead breaker, motorcycle jack, and valve stem tool—attempting this with improvised tools risks damaging the rim or injuring yourself.
  • The tire must be completely deflated and the bead (the edge where the tire meets the rim) must be fully broken free before you can remove the old tire.
  • When installing the new tire, seat the bead evenly on both sides of the rim and inflate slowly while checking that the tire line stays centered.
  • After installation, the wheel must be balanced on a motorcycle wheel balancer before you reinstall it on the bike, or vibration will develop at highway speeds.
  • If you are not confident with any step, a tire shop can change the tire for $30 to $60 per wheel plus the cost of the tire itself.

Breaking the bead and removing the old tire

The bead is the edge of the tire that sits against the rim. It must be completely separated before the tire will come off. Use your bead breaker by positioning it so the flat part presses down on the tire sidewall while the curved part hooks under the rim. Push down firmly on the handle to force the bead away from the rim. Work your way around the entire circumference of the wheel, breaking the bead on both the top and bottom of the tire. This step takes patience—rushing it can bend the rim.

Once the bead is broken all the way around, use your tire irons to pry the tire off the rim. Insert the flat end of the tire iron under the tire bead and lever it up and over the rim edge. Work slowly and use two tire irons at once, one on each side of the wheel, so you don't pinch the inner tube (if your bike has one) or damage the rim. As you work the tire off, the valve stem will come free. If your bike has a tube, remove it now and set it aside.

Preparing the rim and installing the new tire

Before you put the new tire on, inspect the rim for cracks, dents, or corrosion. If the rim is damaged, the new tire will not seal properly and you will have a slow leak or a blowout. Wipe the rim clean with a dry cloth to remove any dirt or old rubber debris. If your motorcycle uses a tube (check your owner's manual), install a new tube now—reusing an old tube risks a puncture. Inflate the new tube slightly so it holds its shape, then position it inside the new tire.

Lay the new tire on the rim and begin working the bead onto the rim by hand, starting at the valve stem. Push the tire bead down into the center of the rim as you work your way around—this creates slack that makes the tire easier to seat. Once you have worked the tire bead onto the rim all the way around by hand, use your tire irons to finish seating it. Work from opposite sides of the wheel so the tire stays centered. This is slower than it sounds, but rushing creates pinch flats or a bead that doesn't seat evenly.

Seating the bead and inflating the tire

Once the tire is on the rim, you need to seat the bead—force it into the groove on the rim where it belongs. Insert the valve stem core back into the valve stem and tighten it by hand. Use an air compressor to inflate the tire slowly to about 15 psi. At this pressure, the tire should begin to seat itself; you will hear a distinct pop or click as the bead snaps into the groove on each side of the rim. If you don't hear this sound, the bead is not seated and you need to deflate and try again.

Once both beads have seated, continue inflating to the pressure listed on your motorcycle's sidewall or in your owner's manual—usually between 28 and 36 psi for street bikes, higher for cruisers. Inflate slowly and stop every few psi to check that the tire line (a painted or molded line on the tire sidewall) stays centered on the rim. If the line is off-center, deflate, break the bead again, and reseat it. An off-center tire will cause vibration and uneven wear.

Balancing the wheel

A tire that is not balanced will vibrate at certain speeds, usually between 40 and 60 mph. This vibration wears the tire faster, stresses the wheel bearings, and makes the bike uncomfortable to ride. After you install the new tire, take the wheel to a tire shop and have it balanced on a motorcycle wheel balancer

If you own a motorcycle wheel balancer, you can balance the wheel yourself at home. Mount the wheel on the balancer, spin it, and watch where it settles. Add stick-on weights to the heavy side until the wheel stays level no matter where you spin it. Check the balance in two or three different positions to make sure it is correct.

Reinstalling the wheel and test riding

Once the tire is installed, balanced, and inflated to the correct pressure, reinstall the wheel on your motorcycle. Align the axle holes with the fork or swingarm, slide the axle through, and tighten the axle nut to the torque specification in your owner's manual—usually between 50 and 80 foot-pounds for the front wheel and 80 to 120 for the rear. Use a torque wrench to get this right; an undertightened axle nut can loosen and cause the wheel to shift, while an overtightened one can strip the threads.

Before you ride, spin the wheel by hand to make sure it turns freely and doesn't rub the brake pads or fender. Check the tire pressure one more time with a gauge. Then take a short test ride at low speed in a parking lot or quiet street, braking gently to make sure the brakes feel normal and the wheel doesn't vibrate. If everything feels right, you can ride normally. If you feel vibration or the brakes feel soft, stop and check the tire pressure and wheel balance again.

When to take your motorcycle to a shop instead

Tire changing is a learnable skill, but it is not for everyone. If you don't have a motorcycle jack, a bead breaker, or tire irons, buying these tools costs $60 to $150. If you only change tires once every few years, a shop is the better choice. A tire shop can change both tires, balance both wheels, and dispose of the old tires for $60 to $120 per wheel plus the cost of the tires. This is money well spent if you are not confident in your ability to seat the bead evenly or balance the wheel correctly—a mistake here creates a safety problem that you will feel every time you ride.

Some riders change their own tires to save money or because they like working on their bikes. Others prefer to have a professional do it and know the job was done right. Either choice is valid. The important thing is that the tire is the correct size, the bead is seated evenly, the wheel is balanced, and the axle nut is torqued to spec. If you are not sure you can do all of these things, take the wheel to a shop.

Frequently Asked Questions

Can I use a car tire iron to change a motorcycle tire?

No. Car tire irons are too long and too thick for motorcycle rims, and they can bend the rim or damage the tire. Motorcycle tire irons are shorter and have a different curve. They cost $15 to $30 for a set of three and are worth buying if you plan to change tires more than once.

What if the bead won't seat no matter how much air I put in?

The bead is probably not fully broken free from the rim, or there is dirt or old rubber stuck in the groove. Deflate completely, use the bead breaker again all the way around the wheel, then clean the rim groove with a cloth. Reseat the bead by hand as far as you can, then inflate slowly and listen for the pop that tells you the bead has seated.

Do I have to balance the wheel myself, or can I ride it unbalanced?

You can ride an unbalanced wheel, but you will feel vibration, the tire will wear unevenly and faster, and the wheel bearings will wear out sooner. Balancing costs $10 to $20 and takes 15 minutes at a shop. It is not optional if you want the tire to last and the bike to feel smooth.

How tight should the axle nut be?

Check your owner's manual for the exact torque specification—it varies by motorcycle. Use a torque wrench and tighten to that number, not by feel. An undertightened nut can loosen and cause the wheel to shift; an overtightened one can strip the threads or crack the axle.

Can I change a motorcycle tire without a center stand or jack?

No. You need the wheel completely off the ground and the bike stable so you can work safely. A motorcycle jack or center stand is not optional. If your bike doesn't have a center stand, use a motorcycle jack rated for your bike's weight.