Tire chains go on your drive wheels, not your spare, and must be tight enough that they don't rattle but loose enough to spin freely
Tire chains are metal links that wrap around your tire to bite into snow and ice. They attach to the wheel rim and sidewall with hooks, clips, or tightening mechanisms. On a front-wheel-drive car, chains go on the front wheels. On a rear-wheel-drive car, they go on the rear wheels. On all-wheel drive, check your owner's manual — some vehicles require chains on all four wheels, others on the drive wheels only.
The attachment process takes 15 to 30 minutes per wheel when you're learning, and faster once you've done it once. You do this work in the snow, in the cold, so understanding the steps before you need them matters. Chains that are installed wrong can break, damage your wheel well, or come loose and wrap around your suspension.
Key Takeaways
- Tire chains attach only to your drive wheels — front wheels on front-wheel-drive cars, rear wheels on rear-wheel-drive cars — and you must check your owner's manual for all-wheel-drive vehicles.
- Before you buy chains, measure your tire size from the sidewall and verify the chain size matches your tire diameter, because chains that are too large or too small will not grip or will damage the wheel.
- The chain must be routed so the side chains (the vertical straps) sit on the outer edge of the tire, and the cross-chains (the horizontal links) sit across the tread, not twisted or bunched.
- After driving 50 feet, stop and retighten the chains, because they loosen as the tire settles and the snow compacts — a loose chain can break or wrap around suspension parts.
- Drive slowly in chains, no faster than 30 mph, and remove them as soon as you reach clear pavement, because chains wear the tire and damage dry asphalt.
Measure your tire and buy the right chain size
Open your driver's door and look at the placard on the inside of the door jamb. It lists your tire size in a format like 225/65R17. The first number is width in millimeters, the second is sidewall height as a percentage of width, the R means radial, and the last number is wheel diameter in inches. For chains, the wheel diameter is what matters — in this example, 17 inches.
Tire chains are sold by the size they fit. A package labeled "Chains for 16–18 inch wheels" will work on your 17-inch tire. Buy chains rated for your exact wheel diameter or the range that includes it. Chains that are too large will rattle and slip. Chains that are too small will not close around the tire and will damage the sidewall if you force them.
Bring your tire size with you when you shop, or order online with the diameter written down. Do not guess. A chain that does not fit is useless in a snowstorm.
Position the car and lay out the chain
Park on level ground, away from traffic, with the engine off. Engage the parking brake. If you're on a slope, point the wheels downhill so the car will not roll if the brake fails.
Lay the chain flat on the ground in front of the tire you're chaining. Spread it out so you can see the entire loop — the side chains (the two long vertical straps), the cross-chains (the horizontal links running across), and the tightening mechanism (usually a ratchet, cam lever, or hook-and-tighten system at the bottom).
Check that the chain is not twisted. The cross-chains should form a ladder pattern across the tire tread. If the chain is tangled, untangle it now before you try to fit it to the wheel.
Drape the chain over the tire and connect the sides
Lift the chain and drape it over the top of the tire so it hangs down both sides. The side chains should sit on the outer edge of the tire — not on the sidewall, but on the outer rim of the tread. The cross-chains should hang down the front and back of the tire.
Reach under the tire and pull the bottom of the chain forward. You will be connecting the two ends of the chain at the bottom of the wheel, underneath the tire. Most chains have hooks on one end and a series of holes on the other end. Pull the hooked end toward the hole-end and insert the hook into the correct hole. The chain should be snug but not so tight that you cannot move it by hand.
If your chain uses a cam lever or ratchet instead of hooks and holes, follow the manufacturer's instructions for your specific model. The principle is the same: connect the two ends at the bottom of the wheel so the chain forms a closed loop around the tire.
Tighten the chain and check the fit
Once the chain is connected, tighten it using the tightening mechanism. If it's a ratchet, turn the handle clockwise until the chain is snug. If it's a cam lever, flip it down and tighten. If it's a hook-and-tighten system, pull the excess chain through and re-hook it in a tighter hole.
The chain should be tight enough that it does not rattle or move when you push on it, but loose enough that you can slide one finger between the chain and the tire. If the chain is too tight, it will overheat the tire and break. If it's too loose, it will rattle, slip, and come off.
Spin the tire by hand to make sure the chain rotates freely without hitting the wheel well or suspension. If the chain catches, loosen it slightly and reposition the side chains so they sit further out on the tire edge.
Install chains on the second drive wheel
Repeat the process on the other drive wheel. Lay the chain out, drape it over the tire, connect the ends underneath, and tighten. Make sure both chains are equally tight — if one is looser than the other, the car will pull to one side.
Once both wheels are chained, drive forward slowly about 50 feet and stop. Get out and check both chains. They will have loosened as the tire settled and the snow compacted underneath. Retighten both chains using the same method you used to tighten them the first time. This is not optional — a loose chain will break or wrap around your suspension and cause serious damage.
Drive carefully and remove chains on clear pavement
Tire chains are designed for snow and ice only. Drive no faster than 30 mph, even if the road feels clear. Chains reduce traction on dry pavement and wear the tire rapidly. Accelerate and brake gently, and avoid sharp turns.
As soon as you reach clear, dry pavement, stop and remove the chains. Loosen the tightening mechanism, disconnect the ends, and pull the chain out from under the tire. Lay the chain on the ground and let it dry before you store it, because wet chains will rust.
Store chains in a dry place in your trunk or garage. Before next winter, inspect them for rust, broken links, or bent hooks. Chains that are damaged should be replaced, not repaired.
Frequently Asked Questions
Can I drive on the highway with tire chains?
Some states and provinces allow chains on highways in winter conditions, but many restrict them to mountain passes or require them only when snow is actively falling. Check your local regulations before you drive. Even where chains are legal on highways, drive slowly — 30 mph is the standard safe speed — and remove them as soon as you reach clear pavement.
What if the chain breaks while I'm driving?
Stop when ready and pull to the side of the road. A broken chain can wrap around your suspension and cause steering or brake failure. Remove the broken chain and the chain from the other wheel on that axle. Drive slowly to the nearest safe location without chains. Do not continue driving on chains if one is broken.
Do I need chains on all four wheels?
Check your owner's manual. Front-wheel-drive cars need chains on the front wheels only. Rear-wheel-drive cars need chains on the rear wheels only. All-wheel-drive vehicles vary — some require chains on all four wheels, others on the drive wheels only. Using chains on only two wheels when four are required can cause the car to slide or spin.
How tight should tire chains be?
Tight enough that the chain does not rattle or move when you push on it, but loose enough that you can slide one finger between the chain and the tire. Too tight and the tire will overheat and the chain will break. Too loose and the chain will slip and come off. Retighten after driving 50 feet.
Can I leave chains on while driving on dry pavement?
No. Chains wear the tire rapidly and reduce traction on dry roads. Remove them as soon as you reach clear pavement. Driving on chains on dry asphalt also damages the road surface and is illegal in many places.