Finding your oil filter before you change it
Your oil filter is almost always mounted on the side or bottom of your engine, held in place by a threaded collar that screws onto a port. On most cars made in the last 20 years, it sits somewhere between the engine block and the frame — usually within arm's reach if you get under the car or lean over the engine bay. The exact location depends on your engine layout and how the manufacturer arranged the plumbing, but you can find it in your owner's manual or by looking for a cylindrical canister about the size of a soda can with a metal base.
Why this matters: if you cannot locate your filter before you start an oil change, you will drain the old oil, then realize you cannot finish the job. Knowing where it is also helps you understand what happens during a service — the technician is not just draining a pan, they are replacing a component that traps dirt and metal particles your engine produces. When that filter gets clogged, oil cannot flow through it properly, and your engine runs on unfiltered oil, which accelerates wear.
Key Takeaways
- The oil filter is a cylindrical canister mounted directly to the engine block, usually on the side or bottom, and you can find its exact location in your owner's manual or service guide.
- Most filters are accessible without removing other parts, but some vehicles require you to remove a wheel, splash guard, or other components to reach it.
- The filter sits between the engine and the frame, and it is held on by a threaded collar that you turn by hand or with a wrench.
- A clogged filter forces oil to bypass the filter element entirely, meaning unfiltered oil circulates through your engine and causes faster wear.
Common locations by engine type
Inline engines (four or six cylinders in a row) usually have the filter mounted on the side of the block, often near the front or middle of the engine. On front-wheel-drive cars, this often means the filter is on the passenger side of the engine bay, sometimes tucked between the engine and the firewall. You can usually reach it from above without getting under the car.
V-shaped engines (V6 or V8) have the filter mounted on one side of the V, typically the side facing the frame. On some vehicles, especially trucks and SUVs, the filter hangs down from the side of the block and sits lower, which means you may need to get under the vehicle or remove a splash guard to reach it. A few V8 engines have the filter mounted on top of the block, which is the easiest location to access.
Transverse engines (mounted sideways in the engine bay, common in front-wheel-drive cars) can have the filter in less obvious spots because space is tight. Some are mounted on the back of the block facing the firewall, others on the bottom facing the frame. Your owner's manual is essential here because the location varies widely.
How to find it if you do not have the manual
Start by opening your hood and looking at the engine from above. Scan the sides of the engine block for a cylindrical metal canister about 3 to 4 inches in diameter and 4 to 5 inches tall. It will have a flat metal base with a threaded hole in the center — that is the part that screws onto the engine. The base usually has a rubber gasket around the edge.
If you cannot spot it from above, get a flashlight and look underneath the engine bay, toward the frame. Many filters sit low enough that you need to crouch or lie under the front of the car to see them. If you still cannot find it, check the owner's manual (you can find a PDF online by searching your vehicle's year, make, and model plus "owner's manual"), or ask a technician at a shop — they can point it out in 30 seconds.
Do not confuse the oil filter with the air filter. The air filter is usually a larger, flatter box mounted on top of or to the side of the engine, and it is not covered in oil. The oil filter is always cylindrical, always has oil residue on it, and always sits lower on the engine.
What happens when you try to change it
Once you locate the filter, you will see that it screws on like a jar lid. To remove it, you turn it counterclockwise by hand or with an oil filter wrench (a socket-like tool that grips the canister). As you unscrew it, old oil will drain out — this is why you should have a drain pan underneath. Once it comes free, you will see the threaded port it was screwed onto. That port is where the new filter screws back on.
The filter housing itself stays on the engine permanently. You are only replacing the cylindrical cartridge that screws on and off. When you install a new filter, you hand-tighten it until the rubber gasket on its base touches the housing, then turn it another three-quarter turn. Over-tightening makes it hard to remove next time and can damage the gasket.
Why location affects how often you change it
The location of your filter does not change how often you need to replace it — that is determined by your engine type, driving conditions, and oil viscosity. But location does affect how straightforward the job is, and easier jobs are more likely to get done on schedule. If your filter is on top of the engine and accessible from above, you might change it yourself. If it is tucked underneath and requires removing a splash guard, you are more likely to take it to a shop, which is fine — just make sure it gets done.
A filter that sits in a hot spot near the exhaust manifold may degrade slightly faster than one in a cooler location, but modern filters are designed to handle engine bay temperatures. The bigger factor is whether the filter gets changed at the interval your manufacturer recommends, regardless of where it sits.
Accessing difficult filter locations
Some vehicles require you to remove parts to reach the filter. Front-wheel-drive cars sometimes need the passenger-side wheel removed and the splash guard unbolted. Trucks and SUVs with filters mounted low may require you to get under the vehicle on a lift or jack. A few vehicles have the filter mounted inside a plastic housing that requires a special wrench to open.
If your vehicle falls into one of these categories, your owner's manual will show the steps. If you are doing the work yourself, follow those steps in order — removing the wrong part first can make the job harder. If you are paying a shop, this is why some oil changes cost more than others: the labor time is longer because the filter is harder to reach.
Some newer vehicles have cartridge-style filters that sit inside a housing on top of the engine. These require you to unscrew a cap, pull out the filter element, and replace it — no drain pan needed because the old oil stays in the housing. If your manual shows this design, the process is different but usually faster and cleaner.
Frequently Asked Questions
Can I change my oil filter without draining the oil first?
Yes, but old oil will spill out when you unscrew the filter, so you need a drain pan underneath regardless. Most people drain the oil and replace the filter at the same time because the old oil is already coming out. If you are only changing the filter, position the pan carefully and expect some spillage.
What if I cannot reach my oil filter by hand?
Use an oil filter wrench — a socket-like tool that grips the cylindrical canister and lets you turn it with a ratchet. They cost $10 to $30 and fit most standard filters. If your filter is in an unusually tight spot, a swivel-head filter wrench or a strap wrench may work better. Your local auto parts store can show you which one fits your vehicle.
Is it normal for oil to drip from the filter after I change it?
Yes. The filter is full of oil, and some will drain out as you remove it and install the new one. This is why you use a drain pan. If oil continues to drip after you have finished and started the engine, the new filter may not be seated properly — stop the engine, let it cool, and check that the filter is hand-tight and the gasket is making a seal.
Do I need to fill the new filter with oil before screwing it on?
Some mechanics do this, some do not. Pre-filling the filter with fresh oil can reduce the time it takes for oil to reach the filter element when you start the engine, but it is not required. If you do pre-fill, use the same oil you are putting in the engine and pour it slowly into the filter opening so it does not overflow.
What if my vehicle has two oil filters?
Some larger engines and diesel trucks have a main filter and a secondary filter. Your owner's manual will show both locations. You replace both at the same interval. Secondary filters are usually smaller and mounted elsewhere on the engine block — check the manual to find it before you start the job.