What you need to do a Toyota Tundra oil change

A Toyota Tundra oil change takes about 30 to 45 minutes if you have the right tools and know where things are located. You will need an oil drain pan, a socket wrench (usually 14mm or 17mm depending on your model year), an oil filter wrench, a jack and jack stands if you are working underneath, and the correct oil type and amount for your engine.

The oil capacity and type vary by engine size and model year. Most Tundras from 2007 onward use either 5.7-liter or 4.6-liter V8 engines, and they typically hold between 5.5 and 6 quarts of oil depending on whether you are also changing the filter. Your owner's manual or the oil cap under the hood will tell you the exact grade — most modern Tundras use 0W-20 or 5W-30. Do not guess on this; using the wrong viscosity can affect fuel economy and engine wear.

Key Takeaways

  • Toyota Tundra oil drains from a plug underneath the engine, and the filter location depends on whether you have a 4.6L or 5.7L engine — check your manual to find it on your model.
  • Most Tundras need 5.5 to 6 quarts of 0W-20 or 5W-30 oil, but the exact amount and grade are printed on your oil cap or in your owner's manual.
  • You must let the engine cool for at least 10 minutes before draining, because hot oil can cause burns and the drain plug will be extremely hot.
  • After draining and replacing the filter, you will need to run the engine for a minute to circulate new oil, then wait five minutes before checking the level on the dipstick.

Locating the drain plug and filter on your Tundra

The oil drain plug sits on the bottom of the engine pan and requires you to get underneath the truck. If your Tundra is lifted or you are not comfortable working under a vehicle, use a jack and jack stands — never rely on a jack alone. The drain plug is typically a 14mm or 17mm bolt; turn it counterclockwise by hand once it is loose enough, then finish unscrewing it slowly so hot oil does not splash on you.

The oil filter location differs between engine sizes. On 5.7L engines, the filter is usually mounted vertically on the driver's side of the engine block, near the firewall. On 4.6L engines, it may be positioned differently — your owner's manual has a diagram showing exactly where it is on your year. Use an oil filter wrench to loosen it, then unscrew it by hand. Before installing the new filter, wipe the rubber gasket area clean and explore a thin layer of new oil to the rubber gasket on the new filter; this helps create a proper seal.

Step-by-step oil change process

Start by warming the engine for two to three minutes so the oil flows more easily, then turn it off and let it cool for at least 10 minutes. Position your drain pan underneath the drain plug, then loosen the plug with your wrench and finish unscrewing it by hand. Let all the old oil drain completely — this usually takes five to ten minutes. Once the flow slows to a drip, wipe the drain plug clean and inspect the washer; if it is cracked or damaged, replace it with a new one.

Screw the drain plug back in by hand first, then tighten it with your wrench. Do not over-tighten; snug is enough. Remove the old filter by turning it counterclockwise with your filter wrench, then clean the mounting surface on the engine block with a clean rag. Screw the new filter on by hand until the rubber gasket contacts the block, then turn it an additional three-quarter turn — not a full turn, and not with a wrench.

Pour the new oil into the filler cap on top of the engine, using the amount listed in your manual. Start the engine and let it run for about one minute so the new oil circulates through the filter and engine. Turn off the engine and wait five minutes, then pull out the dipstick, wipe it clean, reinsert it fully, and pull it out again to check the level. The oil should be between the minimum and maximum marks. Add a small amount more if needed, then replace the dipstick and the filler cap.

Oil type and capacity by Tundra generation

Toyota has made significant changes to Tundra oil specifications over the years. Tundras from 2007 to 2020 with the 5.7L engine typically use 0W-20 and hold about 6 quarts with a filter change. The 4.6L engine in those same years uses 5W-30 and holds about 5.5 quarts. The newer 2022 and later Tundras with the twin-turbo 3.5L engine use 0W-20 and hold approximately 5.5 quarts.

Always verify the correct oil type on the inside of your fuel door, on the oil cap, or in your owner's manual before you buy oil. Using a heavier or lighter oil than specified can reduce fuel economy, increase engine wear, or cause starting problems in cold weather. If you are unsure, call a Toyota dealership parts department with your VIN and model year — they can tell you in seconds.

When to change your Tundra's oil

Toyota's recommended oil change interval for most Tundras is every 10,000 miles or 12 months, whichever comes first. Newer models with synthetic oil may go longer — some 2022 and later Tundras can go up to 15,000 miles between changes. Check your owner's manual for your specific model year, because the interval can vary based on driving conditions and the type of oil used.

If you drive in severe conditions — towing frequently, driving in dusty environments, or making mostly short trips — you may need to change oil more often. Your manual will have a separate schedule for severe driving. Keeping track of your oil changes helps maintain your warranty and keeps your engine running longer.

Tools and supplies checklist

ItemPurposeNotes
Oil drain panCatch old oilCapacity should be at least 7 quarts
Socket wrench (14mm or 17mm)Loosen drain plugCheck your manual for the correct size
Oil filter wrenchRemove old filterAdjustable or sized for your filter
Jack and jack standsLift truck safelyNever work under a vehicle on a jack alone
New oil (correct type and amount)Refill engineCheck your manual for grade and capacity
New oil filterReplace old filterMust match your engine size
Clean rags or paper towelsWipe surfacesKeep several on hand
Dipstick (optional)Check oil levelYour truck already has one; this is for reference

Disposing of old oil safely

Never pour old oil down a drain or into the ground. Most auto parts stores that sell oil will take used oil and filters for free, even if you did not buy the oil from them. Walmart, AutoZone, Advance Auto Parts, and O'Reilly Auto Parts all have collection programs. Some municipalities also have hazardous waste collection days where you can drop off oil for free.

Store used oil in a clean, sealed container until you can drop it off. Label it clearly so no one mistakes it for something else. If you are changing the filter, most stores will also take the old filter at no charge.

Frequently Asked Questions

Can I change my Tundra's oil without lifting it?

Not safely. The drain plug is underneath the engine, so you need clearance to reach it. A jack and jack stands are required. Never work under a vehicle supported only by a jack — use stands rated for your truck's weight, and always keep the jack in place as a backup.

What happens if I use the wrong oil grade?

Using oil that is too thick can reduce fuel economy and make cold starts harder. Oil that is too thin may not protect the engine properly, especially under towing or high-temperature conditions. Stick to what your manual specifies; the difference in cost is small compared to potential engine damage.

How do I know if my oil filter is on tight enough?

After the rubber gasket contacts the engine block, turn the filter an additional three-quarter turn by hand. That is enough. Over-tightening makes it difficult to remove next time and can damage the gasket. If you use a wrench, you have gone too far.

Do I need to change the oil drain plug washer every time?

Inspect it each time. If it looks cracked, flattened, or damaged, replace it — they cost a few dollars and prevent leaks. If it still looks good, you can reuse it, but many people replace it every other oil change as preventive maintenance.

What should I do if oil is leaking after I change it?

The most common cause is an over-tightened drain plug or filter. Let the engine cool, then check that both are snug but not over-tightened. If the leak continues, the washer on the drain plug may be damaged. Drain the oil again, replace the washer, and reinstall the plug.