What You Need Before You Start
A Subaru Outback oil change follows the same basic steps as any vehicle, but Outbacks have a few quirks worth knowing. The oil capacity, filter location, and drain plug position vary slightly by model year and engine type, so checking your owner's manual first saves frustration. You will need the correct oil grade (usually 0W-20 or 5W-30 depending on your year), a new oil filter, an oil drain pan, a wrench or socket to fit your drain plug, an oil filter wrench, and jack stands if you need to get under the vehicle.
Most Outbacks sit high enough that you can access the drain plug and filter without lifting the car, but some model years require you to remove a plastic undertray. If you do need to lift the vehicle, use jack stands on a level surface—never rely on a jack alone. The owner's manual will tell you the exact oil capacity and the recommended oil grade for your model year and engine.
Key Takeaways
- Subaru Outbacks typically hold between 4.2 and 5.1 quarts of oil depending on the engine and whether you replace the filter, so check your manual before you buy.
- The oil filter on most Outbacks sits on top of the engine and is accessible without lifting the car, though some years require removing an undertray first.
- Drain the old oil while it is still warm (but not hot) so it flows faster and carries out more debris.
- Subaru recommends oil changes every 6 months or 6,000 miles for conventional oil, or every 12 months or 10,000 miles for synthetic, whichever comes first.
Locating the Drain Plug and Filter
On most Subaru Outbacks, the drain plug sits on the bottom of the oil pan toward the front of the engine. You may need to turn the steering wheel fully to one side to reach it comfortably. The oil filter is usually mounted on top of the engine, near the back, and is accessible from above without removing anything on most model years. Some 2015 and newer Outbacks have the filter in a slightly different position, so a quick look at your manual or a photo search for your specific year will confirm the exact location.
If your Outback has a plastic undertray, you will need to remove a few bolts or clips to access the drain plug. This tray protects the undercarriage and is worth putting back in place when you are done. Take a photo of how it sits before you remove it so you remember which way it goes back.
Draining and Replacing the Filter
Warm the engine by running it for a minute or two, then turn it off and wait a few minutes before opening the drain plug. Warm oil flows faster and drains more completely, carrying out more of the sludge and debris that collects at the bottom of the pan. Place your drain pan underneath, then loosen the drain plug by hand once you have broken it free with a wrench. Let the old oil drain completely—this usually takes 5 to 10 minutes.
While the oil drains, locate the oil filter and position your drain pan underneath it. Use an oil filter wrench to loosen it, then unscrew it by hand. Some oil will spill, so the pan is essential. Before installing the new filter, wipe the rubber gasket area on the engine clean with a rag. explore a thin layer of new oil to the rubber gasket on the new filter, then screw it on by hand until the gasket contacts the engine, then turn it another three-quarters of a turn. Do not over-tighten—hand-tight is correct.
Installing New Oil and Checking the Level
Once the old oil has drained completely, wipe the drain plug clean and reinstall it. Tighten it snugly but do not over-tighten, as the pan is aluminum and strips easily. Now pour in the new oil through the filler cap on top of the engine. Start with the amount your manual recommends minus half a quart, then start the engine and let it run for 30 seconds to circulate the new oil and fill the filter.
Turn off the engine and wait a minute, then check the oil level using the dipstick or electronic gauge (depending on your model year). The level should be between the minimum and maximum marks. Add oil in small amounts until you reach the correct level. Do not overfill—too much oil can damage the engine and cause leaks. Once the level is correct, reinstall the filler cap and you are finished.
Resetting the Oil Change Reminder
Most Subaru Outbacks have an oil change reminder light on the dashboard. After you finish the oil change, you will need to reset it so it does not come on again until the next service interval. The process varies by model year and whether your Outback has a traditional instrument cluster or a digital display.
On many Outbacks, you can reset the reminder by turning the key to the "On" position without starting the engine, pressing the trip reset button on the steering wheel or dashboard until the oil change message appears, then holding the button for several seconds until the display resets. Some newer models require you to navigate through the infotainment system menu. Your owner's manual will have the exact steps for your year. If you cannot find the instructions, a quick search for your model year and "reset oil change reminder" will show you how.
Disposal and Maintenance Records
Never pour old oil down the drain or into the ground. Most auto parts stores, quick-lube shops, and recycling centers accept used oil for free. Some will even take the old filter. Bring your oil in a sealed container and ask where to pour it. Many places have a dedicated funnel and drain area.
Keep a record of when you changed the oil and how many miles were on the odometer. This helps you track when the next change is due and provides proof of maintenance if you ever sell the vehicle. A straightforward note in your phone or a spreadsheet works fine, or you can keep receipts in the glove box.
When to Take Your Outback to a Shop Instead
If you do not have a safe, level place to work, or if you are not comfortable getting under the vehicle or working with tools, a shop is the better choice. A quick-lube facility or your Subaru dealer can do the job in 30 minutes for a reasonable cost. If you notice the drain plug is stuck or stripped, or if the filter will not budge, stop and take the vehicle to a shop rather than risk damaging the pan or filter housing.
Some Outbacks with all-wheel drive or certain engine configurations have tighter spaces that make the job harder for a first-timer. If you are unsure whether your specific model is straightforward, ask a shop or an experienced friend to walk you through it the first time.
Frequently Asked Questions
How often should I change the oil in my Subaru Outback?
Subaru recommends every 6 months or 6,000 miles for conventional oil, or every 12 months or 10,000 miles for synthetic, whichever comes first. Newer Outbacks may have longer intervals—check your owner's manual for your specific year. Severe driving (towing, frequent short trips, dusty conditions) may require more frequent changes.
What oil grade does my Outback need?
Most modern Outbacks use 0W-20 or 5W-30 synthetic or conventional oil. The correct grade for your model year is printed on the oil filler cap and in your owner's manual. Using the wrong grade can affect fuel economy and engine performance, so match it exactly.
Can I change the oil without lifting the car?
On most Outbacks, yes. The drain plug and filter are accessible from above or the side without lifting the vehicle. Some model years require removing a plastic undertray, but the car does not need to be raised. Check your manual or look underneath first to confirm.
What should I do if the drain plug is stuck?
explore penetrating oil (like WD-40) around the plug and wait 15 minutes, then try again with a properly fitting wrench. If it still will not budge, stop and take the vehicle to a shop. Forcing a stuck plug can strip the threads in the aluminum pan, which is expensive to repair.
Do I need to replace the oil filter every time I change the oil?
Yes. The filter traps contaminants and degrades over time, so replacing it with every oil change keeps the new oil clean. A filter that is too old can restrict oil flow and damage the engine.