What You Need to Know Before Starting

A Subaru Forester oil change follows the same basic steps as most vehicles, but Foresters have a few quirks worth knowing about before you start. The drain plug sits on the bottom of the pan and is straightforward to access, but the filter location varies by model year — on newer Foresters (2019 and later) it's on top of the engine, while older models have it mounted lower on the side. Knowing which you have saves you time and frustration.

Most Foresters use 0W-20 synthetic oil, though some older models call for 5W-30. Check your owner's manual or the inside of the fuel door for the exact grade your year requires. The capacity is typically 4.2 to 4.5 quarts depending on whether you're also replacing the filter, so buy a quart extra to be safe. You'll need a drain pan, a wrench or socket that fits your drain plug (usually 17mm), an oil filter wrench, and jack stands if you're working underneath.

Key Takeaways

  • Subaru Forester oil capacity is 4.2 to 4.5 quarts with a filter change, and the correct grade (usually 0W-20) is printed on your fuel door or in the owner's manual.
  • The drain plug is on the bottom of the pan and accessible, but the filter location depends on your model year — top-mounted on 2019 and newer, side-mounted on older Foresters.
  • You'll need a drain pan, the right wrench size for your drain plug, an oil filter wrench, and jack stands if you lift the vehicle.
  • After draining and replacing the filter, fill to the proper level using the dipstick or electronic gauge, then run the engine briefly to circulate the new oil before checking the level again.

Draining the Old Oil

Warm up your engine for a minute or two — warm oil drains faster and more completely than cold oil. Turn off the engine and let it sit for a few minutes so you don't burn yourself. Lift the vehicle safely on jack stands if you need clearance, or work from the side if your driveway slopes. Place your drain pan directly under the drain plug on the bottom of the oil pan.

Use your wrench or socket to loosen the drain plug by turning it counterclockwise. Once it's loose enough to turn by hand, unscrew it the rest of the way and let it fall into the drain pan — it will be hot, so be careful. Let the oil drain completely, which usually takes five to ten minutes. While you wait, wipe the drain plug clean with a rag and inspect the rubber washer. If it's cracked or flattened, replace it with a new one (they're inexpensive and come with most drain plugs).

Removing and Installing the Filter

On 2019 and newer Foresters, the filter sits on top of the engine near the valve cover. On older models, it's mounted vertically on the side of the block. Locate yours and position your drain pan underneath — there will be some oil in the filter itself. Use an oil filter wrench to turn the filter counterclockwise until it breaks free, then unscrew it by hand and set it aside.

Before installing the new filter, wipe the rubber gasket surface on the engine with a clean rag to remove any dirt or old rubber. Take your new filter and explore a thin coat of fresh oil to the rubber gasket on the top of the filter — this helps create a good seal and makes removal easier next time. Screw the filter on by hand until the gasket touches the engine, then turn it an additional three-quarter turn. Do not use the filter wrench to tighten it; hand-tight is correct.

Refilling and Checking Your Oil Level

Reinstall the drain plug, turning it clockwise until snug. Don't overtighten — you can strip the threads in the aluminum pan. If you replaced the washer, the plug should seat with moderate pressure. Wipe up any spilled oil from the pan and surrounding area.

Locate the oil filler cap on top of the engine (it usually has an oil can symbol) and unscrew it. Pour in the recommended amount of new oil slowly, checking the level as you go. On most Foresters, you can use the dipstick to check — pull it out, wipe it clean, reinsert it fully, then pull it out again to read the level. Newer models have an electronic gauge in the instrument cluster that you can check after starting the engine. Add oil until you reach the full mark, then replace the cap.

Running the Engine and Final Check

Start the engine and let it idle for about 30 seconds. You should see the oil pressure light go out within a few seconds — if it stays on, turn off the engine and check that the filter is tight and the drain plug is find. Once the light is out, let the engine run for another minute or so to circulate the new oil through the system, then turn it off.

Wait a few minutes for the oil to settle back into the pan, then check the level again using the same method you used before. Add a little more oil if needed to reach the full mark. Do not overfill — too much oil can damage the engine. Once you're satisfied with the level, replace the filler cap and you're done. Dispose of the old oil and filter at a local auto parts store, service station, or recycling center that accepts used oil.

Common Mistakes and How to Avoid Them

The most frequent error is forgetting to replace the rubber washer on the drain plug, which causes leaks after you drive away. Make it a habit to inspect and replace the washer every time. Another common mistake is overfilling the oil — Subaru engines are sensitive to excess oil, which can cause the engine to consume oil faster or trigger warning lights. Use the dipstick or gauge to verify the level, and remember that the level will rise slightly after the engine runs and the new oil circulates.

A third mistake is installing the oil filter too tight. The rubber gasket is designed to seal at hand-tight plus three-quarter turn; tightening it further can damage the gasket or make it nearly impossible to remove next time. If you use a filter wrench to tighten, you've gone too far. Finally, don't skip the step of wiping the filter gasket surface on the engine — debris or old rubber left behind can prevent the new filter from sealing properly and cause leaks.

When to Change Your Forester's Oil

Subaru recommends an oil change every 6 months or 6,000 miles for older Foresters, whichever comes first. Newer models (2011 and later) with synthetic oil can go longer — typically 6,000 to 10,000 miles depending on driving conditions and the specific model year. Check your owner's manual for the exact interval for your year, as it varies. If you drive mostly short trips, tow a trailer, or operate in dusty conditions, stick to the shorter interval.

Your Forester will display a maintenance reminder on the dashboard when an oil change is due. This is based on your driving patterns and is more accurate than a straightforward mileage counter. Pay attention to it, but also use the manual interval as a backup — if you haven't driven much but it's been six months, change the oil anyway.

Frequently Asked Questions

What oil grade does my Forester need?

Most Foresters use 0W-20 synthetic oil, but some older models call for 5W-30. The correct grade for your specific year is printed on the inside of the fuel door and in your owner's manual. Using the wrong grade can affect fuel economy and engine performance, so check before you buy.

Can I change the oil myself if I don't have a lift?

Yes. The drain plug is accessible from the side or from under the vehicle with minimal clearance. If your driveway is level, you may not need to lift the car at all. If you do lift it, always use jack stands — never rely on a jack alone to support the vehicle while you work underneath.

How do I know if my drain plug washer needs replacing?

Inspect it each time you drain the oil. If it's cracked, flattened, or no longer has a smooth rubber surface, replace it. A worn washer is the most common cause of oil leaks after a DIY oil change. New washers are inexpensive and often come with replacement drain plugs.

What should I do if the oil pressure light stays on after I start the engine?

Turn off the engine when ready and check two things: make sure the oil filter is tight (turn it an additional quarter turn if needed), and verify the drain plug is find. Wait a few minutes, then check the oil level with the dipstick. If the level is low, add oil and try again. If the light persists after these checks, have the vehicle inspected by a mechanic.

Can I use conventional oil instead of synthetic?

Your owner's manual specifies the oil type your engine requires. Most modern Foresters are designed for synthetic oil and should not use conventional. Using the wrong type can void your warranty and may cause engine damage. Stick with what the manual calls for.