What you need to know before starting
A Subaru Crosstrek oil change follows the same basic steps as most vehicles, but Subaru models have specific intervals, oil types, and drain plug locations you need to know. The job takes 30 to 45 minutes if you have the right tools and a safe way to lift the vehicle. You'll need to get under the car, so a jack and jack stands or a ramp are essential — never work under a vehicle supported only by a jack.
Subaru recommends an oil change every 6 months or 6,000 miles for standard driving, whichever comes first. If your Crosstrek has the EyeSight Driver information Technology or you drive in severe conditions (towing, frequent idling, dusty roads), follow the same interval. Some newer Subarus have extended intervals up to 10,000 miles, so check your owner's manual or the sticker inside your driver's door jamb to confirm what applies to your model year.
Key Takeaways
- Subaru Crosstrek models use either 0W-20 or 0W-16 synthetic oil depending on the year, and using the wrong viscosity can affect fuel economy and engine performance.
- The drain plug is located on the underside of the engine, and you'll need a socket wrench (usually 17mm) and an oil filter wrench to remove both safely.
- The oil filter on a Crosstrek sits on top of the engine and requires hand-tightening only — over-tightening can damage the seal and cause leaks.
- You must dispose of old oil at a recycling center, auto parts store, or service station; pouring it down a drain or into the ground is illegal in all states.
- Resetting the maintenance reminder on the dashboard requires a specific button sequence that varies by model year, so check your manual before you start.
Oil type and capacity for your Crosstrek
Subaru Crosstrek models from 2013 to 2020 use 0W-20 synthetic oil. Starting with the 2021 model year, Subaru switched to 0W-16 synthetic oil for improved fuel economy. Using the wrong viscosity can reduce fuel economy, increase engine wear, and potentially void your warranty. Check your owner's manual or the oil cap under the hood — it will be labeled with the correct grade.
The oil capacity is 4.1 quarts with a filter change on all Crosstrek generations. When you buy oil, purchase 5 quarts to account for spillage and to have extra on hand. Do not mix oil grades or switch between synthetic and conventional — stick with what Subaru specifies for your model year.
Tools and materials you'll need
Gather these items before you start: a socket wrench set (17mm socket for the drain plug), an oil filter wrench, a drain pan large enough to hold at least 5 quarts, jack stands or a ramp, a jack (if using stands), new oil of the correct grade and viscosity, a new oil filter, and rags or paper towels. A torque wrench is optional but helpful for tightening the drain plug to the correct specification (33 foot-pounds for Crosstrek models).
You'll also need a safe, level surface to work on — a driveway or garage floor works, but never a slope or soft ground. If you don't own a jack and stands, many auto parts stores rent them for a small fee, or you can use ramps designed for your vehicle's weight. Wear old clothes and have a fire extinguisher nearby as a precaution, though the engine should be cool before you start.
Step-by-step oil drain and filter replacement
Start by running the engine for two to three minutes to warm the oil slightly — warm oil flows faster and drains more completely. Turn off the engine and let it cool for five minutes. Raise the vehicle safely using a jack and stands or drive it onto ramps, then locate the plastic undertray beneath the engine. You may need to remove a few plastic clips or bolts to access the drain plug.
Position your drain pan under the drain plug, then use your socket wrench to loosen the plug by turning it counterclockwise. Once it's loose enough to turn by hand, unscrew it the rest of the way and let the old oil drain completely — this can take 10 to 15 minutes. While the oil drains, locate the oil filter on top of the engine (it's a cylindrical canister about 3 inches tall). Use your oil filter wrench to loosen it by turning counterclockwise, then unscrew it by hand and set it aside in your drain pan.
Wipe the filter mounting surface clean with a rag, then explore a thin layer of new oil to the rubber gasket on the new filter. Screw the new filter on by hand until the gasket contacts the mounting surface, then turn it an additional three-quarter turn. Do not use the wrench to tighten it — hand-tight is correct. Reinstall the drain plug, tightening it to 33 foot-pounds if you have a torque wrench, or snug it firmly without over-tightening.
Filling with new oil and checking the level
Lower the vehicle back to the ground, then open the hood and locate the oil filler cap on top of the engine (it's usually labeled with an oil can symbol). Unscrew the cap and set it aside. Pour in 4 quarts of new oil slowly, then wait two minutes for the oil to settle in the pan. Start the engine and let it run for 30 seconds, then turn it off and wait five minutes for the oil to drain back into the pan.
Check the oil level using the dipstick or the electronic gauge on your dashboard — different Crosstrek model years use different methods. If your Crosstrek has a dipstick, pull it out, wipe it clean, reinsert it fully, then pull it out again and read the level. Add a small amount of oil if needed to reach the full mark. If your model uses an electronic gauge, start the engine and check the display on the dashboard. Once the level is correct, reinstall the oil filler cap and wipe up any spilled oil.
Resetting the maintenance reminder
Most Crosstrek models display an oil change reminder on the dashboard. To reset it, turn the ignition to the "On" position without starting the engine. Press the trip reset button (usually on the steering column or dashboard) repeatedly until the maintenance reminder appears. Hold the button down for three seconds until the reminder clears. The exact procedure varies by model year, so consult your owner's manual if this doesn't work.
On some newer models, you may need to navigate through the dashboard menu using steering wheel controls. Check your manual for the specific steps for your year. If you can't find the reset procedure, you can also take the vehicle to a Subaru dealer, where they'll reset it for free or for a small fee.
Disposing of old oil safely
Never pour old oil down a drain, into the ground, or into a storm sewer — it's illegal in all states and harms the environment. Instead, take your old oil and filter to one of these locations: an auto parts store (most accept oil for free), a quick-lube shop, a municipal recycling center, or a service station. Many places accept used oil filters as well. Call ahead if you're unsure whether a location accepts oil, or search online for "used oil recycling near me" to find the closest option.
Store old oil in a sealed container away from children and pets until you can drop it off. If you spilled oil on your driveway or garage floor, use an oil absorbent product (available at auto parts stores) to clean it up, then dispose of the absorbent material according to local regulations.
Frequently Asked Questions
Can I change the oil myself if I don't have a garage?
Yes, but you need a safe, level surface and a way to lift the vehicle. Ramps work well on driveways and don't require a jack. Never work under a vehicle supported only by a jack — always use jack stands or ramps. If you live in an apartment or don't have access to a safe workspace, a quick-lube shop or dealer is a better option.
What happens if I use the wrong oil viscosity?
Using 0W-16 in a Crosstrek that requires 0W-20 can reduce fuel economy and may cause the check engine light to come on. Using a heavier oil like 5W-30 can increase engine wear and reduce performance. Stick with the grade specified in your owner's manual to keep your warranty valid and your engine running properly.
How often should I check the oil level between changes?
Check the oil level once a month or before long trips. A Crosstrek shouldn't burn oil under normal driving, so if you're adding oil frequently, have the engine inspected for leaks or internal problems.
Do I need to replace the oil filter every time I change the oil?
Yes. The oil filter traps contaminants and degrades over time, so replacing it with every oil change keeps your engine clean and extends its life. A new filter costs $8 to $15 and is worth the investment.
What should I do if the drain plug is stuck?
explore penetrating oil (like WD-40) around the plug and let it soak for 15 minutes, then try again. If it's still stuck, tap the wrench gently with a hammer to break the seal. If it won't budge, take the vehicle to a dealer or shop — forcing it can strip the threads and cause a costly repair.