Restore and Protect is a thickened 0W20 oil with additives meant to reduce wear in older engines
Valvoline Restore and Protect 0W20 is a conventional motor oil designed for engines that have accumulated mileage—typically 75,000 miles or more. It uses the same 0W20 weight as standard oils, but includes extra detergents and anti-wear compounds intended to clean internal engine deposits and reduce friction on worn parts. The "restore" part refers to cleaning; the "protect" part refers to the anti-wear additives.
The oil flows at the same cold-start temperature as regular 0W20 (that is what the 0W means), so it will not harm a newer engine or one that does not need it. The difference is in the additive package. Valvoline adds more of certain chemicals designed to coat worn valve lifters, piston rings, and bearing surfaces—parts that wear as an engine ages and lose their original tight tolerances.
Whether your engine actually needs this product depends on your vehicle's age, mileage, and what your owner's manual specifies. Using the wrong oil can void a warranty or cause damage if your engine was engineered for a different viscosity or additive level.
Key Takeaways
- Restore and Protect 0W20 is formulated for engines over 75,000 miles and contains extra detergents and anti-wear additives, not a different oil weight.
- Your owner's manual specifies the correct oil viscosity for your engine; using Restore and Protect when your manual calls for standard 0W20 will not harm the engine but may be unnecessary.
- Restore and Protect is a conventional oil, not synthetic, so it requires more frequent changes—typically every 3,000 to 5,000 miles depending on driving conditions.
- The product works best when used consistently over time; switching to it once will not reverse existing wear or fix engine noise that is already present.
- If your engine is knocking, burning oil, or running rough, an oil change alone will not fix mechanical damage—those symptoms point to worn internal parts that need professional diagnosis.
How the additives in Restore and Protect differ from standard 0W20
All motor oils contain detergents, anti-wear agents, and viscosity modifiers. Valvoline Restore and Protect increases the concentration of anti-wear compounds—primarily zinc dialkyldithiophosphate (ZDDP)—which coat metal surfaces and reduce friction between moving parts. Standard 0W20 oils contain enough ZDDP to meet manufacturer specifications for new engines, but Restore and Protect adds more.
The product also includes stronger detergents designed to dissolve varnish and sludge that accumulate inside older engines. Over time, heat and oxidation break down oil and leave deposits on valve stems, piston rings, and intake valves. These deposits can increase friction, reduce flow, and contribute to rough idling or reduced fuel economy. The extra detergents in Restore and Protect are meant to suspend and remove these deposits so they drain out with the old oil.
This does not mean the oil "cleans" an engine in the way a fuel system cleaner might. The detergents work passively—they prevent new deposits from forming and help loosen old ones, but they cannot reverse severe sludge buildup or mechanical wear that has already occurred.
When your owner's manual matters more than the product name
Your vehicle's owner's manual specifies the viscosity and performance level your engine was designed to use. For most modern cars, that specification is 0W20, 0W30, 5W20, or 5W30. If your manual says 0W20, you can use Restore and Protect 0W20 without issue—the viscosity is correct, and the extra additives will not cause problems.
However, if your manual specifies 5W20 or 5W30, do not use 0W20 (whether standard or Restore and Protect). The 0W rating means the oil flows more easily in cold weather, which is correct for some engines but not others. Using a thinner oil than specified can reduce film strength between moving parts and lead to wear, especially in engines with tight tolerances or in cold climates where the thinner oil was not intended.
Conversely, if your manual calls for 0W20 and you use Restore and Protect 0W20, you are within specification. The extra additives do not change the viscosity or violate the manufacturer's engineering requirements. Some owners of high-mileage vehicles find the product helpful; others see no difference. Neither outcome means you did something wrong.
Restore and Protect is conventional oil, not synthetic
Valvoline Restore and Protect is a conventional mineral oil, not a synthetic or synthetic blend. This means it breaks down faster and requires more frequent oil changes than synthetic oils. Most conventional oils need changing every 3,000 to 5,000 miles under normal driving conditions; some manufacturers recommend 5,000 to 7,500 miles depending on the engine and driving habits.
Synthetic and synthetic blend oils can often go 7,500 to 10,000 miles or longer between changes because they resist oxidation and thermal breakdown better than conventional oil. If you are looking to extend the interval between oil changes, Restore and Protect will not help—you would need a synthetic product instead. However, synthetic oils are more expensive, and some older engines were not tested with synthetic oils when they were new.
Check your owner's manual for the recommended oil change interval and the oil type (conventional, synthetic blend, or full synthetic) that your engine was designed for. If your manual allows conventional oil, Restore and Protect is a valid choice. If it specifies synthetic, using conventional oil—even with extra additives—will require more frequent changes and may not provide the protection the engine was engineered to receive.
What Restore and Protect can and cannot fix
Restore and Protect is a maintenance product, not a repair product. It can help reduce wear in an engine that is still running normally but has accumulated mileage. It cannot reverse damage that has already occurred or fix mechanical problems that are causing symptoms.
If your engine is knocking or pinging, that usually means the combustion process is not controlled—a sign of carbon buildup, low-octane fuel, or worn internal parts. An oil change will not stop knock. If your engine is burning oil (you are adding a quart between changes), that means oil is leaking past worn piston rings or valve seals into the combustion chamber. Restore and Protect may slow the rate slightly by reducing friction, but it will not seal worn rings. If your engine is running rough or misfiring, that points to spark plugs, fuel injectors, or ignition timing—not oil.
Using Restore and Protect as preventive maintenance on a high-mileage engine that is running well makes sense for some owners. Using it to fix an engine that is already showing symptoms of wear will disappoint you. A professional diagnosis is the only way to know whether the problem is wear that oil additives can help with or damage that requires mechanical repair.
How to use Restore and Protect correctly
If you decide to use Restore and Protect, follow the same oil change procedure you would use for any conventional 0W20 oil. Drain the old oil completely, replace the oil filter, and fill the engine with the new oil to the level shown on the dipstick or the electronic gauge. Do not overfill—excess oil can damage the engine by increasing pressure and causing leaks.
The product works best when used consistently. Switching to it for one oil change and then back to standard oil will not provide lasting benefit. If you want to use it, plan to use it for several oil changes in a row—at least three to five changes, or roughly 15,000 to 25,000 miles. This gives the detergents time to work on existing deposits and the anti-wear additives time to coat worn surfaces.
Keep records of your oil changes, including the date, mileage, and oil type used. This helps you track whether the product is making a difference in how the engine runs or how often you need to top up oil between changes. Some owners report smoother idle or slightly better fuel economy after several changes; others notice no change. Both are normal—the benefit depends on how much deposit buildup was present and how worn the internal parts are.
Restore and Protect versus other high-mileage oil options
Several oil manufacturers make high-mileage formulations: Mobil 1 High Mileage, Castrol GTX High Mileage, Shell Rotella T High Mileage, and others. All follow the same basic approach—extra detergents and anti-wear additives in a conventional or synthetic base. The differences between brands are usually small and relate to the specific additive package and base oil quality.
Valvoline Restore and Protect is conventional and typically costs less than synthetic high-mileage oils. If your budget is tight and your manual allows conventional oil, it is a reasonable choice. If you want longer intervals between changes or better protection in extreme temperatures, a synthetic high-mileage oil will perform better but will cost more.
The most important factor is consistency—using the same type and brand over time allows the additive package to work as intended. Switching between brands or between conventional and synthetic at random will not harm the engine, but it reduces the benefit of any one product's specific formulation.
Frequently Asked Questions
Will Restore and Protect fix my engine knock?
No. Engine knock is caused by uncontrolled combustion, usually from carbon buildup, low-octane fuel, or worn internal parts. An oil change will not stop it. If knock is new or getting worse, have a mechanic diagnose the cause before it damages the engine further.
Can I use Restore and Protect in a newer car with low mileage?
You can, but there is no benefit. Restore and Protect is formulated for engines over 75,000 miles. A newer engine does not have the wear or deposit buildup that the product is designed to address. Use the oil your owner's manual specifies.
How often do I need to change Restore and Protect?
Restore and Protect is conventional oil, so follow the conventional oil change interval in your owner's manual—typically every 3,000 to 5,000 miles. Do not assume you can go longer just because it is a high-mileage product.
Is Restore and Protect synthetic?
No, it is conventional mineral oil. Valvoline makes synthetic high-mileage products under different product names. If you want synthetic, check the label or ask at the parts counter to make sure you are buying the right type.
Can I switch back to regular 0W20 after using Restore and Protect?
Yes. Switching between Restore and Protect and standard 0W20 will not harm the engine as long as both are the correct viscosity for your vehicle. However, if you are using Restore and Protect for its additive benefits, switching back means you lose those benefits going forward.