The oil change light resets differently depending on your Escape's trim level and year

The 2013 Ford Escape has two different reset procedures depending on whether your model has the basic instrument cluster or the more advanced MyFord Touch system. Most 2013 Escapes use the basic cluster, which requires a manual reset at the dashboard. If your Escape has the MyFord Touch infotainment system with the touchscreen, you'll reset the light through the menu instead. Both methods take less than a minute and require no tools.

The reset is separate from the actual oil change — you perform it after you've already changed the oil and filter. Resetting the light tells your Escape's computer to start a new service interval countdown. If you skip this step, the light will stay on even though your oil is fresh, and you'll lose the early warning system for your next service.

Key Takeaways

  • The 2013 Escape with a basic instrument cluster resets the oil light by turning the key to the "On" position without starting the engine, pressing the accelerator three times within 10 seconds, then turning the key back to "Off."
  • Escapes with MyFord Touch reset the light through the Settings menu on the touchscreen by selecting Service and then Oil Change Reset.
  • You must complete the oil change and filter replacement before resetting the light, or the computer will not register the service.
  • The reset procedure does not require a dealer visit or any special equipment — you can do it in your driveway when ready after changing your oil.

Reset procedure for the basic instrument cluster

Start with the engine off and the key in your hand. Insert the key into the ignition and turn it to the "On" position — the position where the dashboard lights up but the engine does not start. You should hear the fuel pump prime for a second or two.

Press the accelerator pedal all the way to the floor three times in quick succession. Do this within a 10-second window. You'll hear a beep or see the lights on the dashboard flicker slightly when the reset takes effect. Turn the key back to "Off." The oil change light should now be gone from your dashboard.

If the light is still on after you turn the key back to "On" to verify, repeat the process. Sometimes the timing needs to be tighter, or the accelerator input needs to be more deliberate. If it still doesn't clear after a second attempt, check that you completed the oil change itself — the computer may be detecting that the oil level or filter condition hasn't actually changed.

Reset procedure for MyFord Touch systems

If your 2013 Escape has the MyFord Touch touchscreen, the reset happens through the vehicle settings menu. Start the engine and let it idle. On the touchscreen, navigate to Settings, then select Service. You should see an option for Oil Change Reset or Maintenance Reset.

Tap that option and confirm when the system asks you to verify. The screen will show a confirmation message, and the oil change light will disappear from your instrument cluster. Turn off the engine and restart it to confirm the light is gone.

If you don't see a Service or Oil Change Reset option in your Settings menu, your Escape may have a different version of MyFord Touch software. In that case, consult your owner's manual for the exact menu path, as Ford changed the menu structure slightly across model years.

What to do if the light won't reset

If you've followed the correct procedure for your cluster type and the light remains on, the most common cause is that the oil change itself wasn't completed properly. Check that you drained the old oil completely, installed a new filter (not a reused one), and filled the crankcase with the correct oil grade and quantity for your engine. The 2013 Escape uses either 5W-20 or 5W-30 depending on engine size — check your owner's manual or the oil cap for the correct grade.

A second possibility is that the reset procedure wasn't executed correctly. Try again, paying close attention to the timing and the firmness of the accelerator presses. Some owners find that holding the accelerator down for a full second on each press, rather than tapping it quickly, works better.

If the light still won't clear after a second attempt with a confirmed oil change, the instrument cluster itself may have a fault, or the oil level sensor may be malfunctioning. At that point, a Ford dealer can run a diagnostic scan to determine whether the computer is detecting an actual service condition or whether there's an electrical issue with the warning system.

Why the reset matters for your maintenance schedule

Ford's oil change intervals for the 2013 Escape are based on engine hours and driving conditions, not just mileage. The onboard computer tracks this and illuminates the light when service is due. If you don't reset the light after an oil change, the computer will keep the warning active even though your oil is fresh. This makes it impossible to know when your next service is actually due.

Resetting the light restarts the service interval counter. From that point forward, the light will come back on when the computer determines that the next oil change is necessary — typically between 5,000 and 10,000 miles, depending on your driving patterns and the engine type.

Frequently Asked Questions

Can I reset the oil light without changing the oil?

Technically yes — the reset procedure doesn't verify that you actually changed the oil. However, you should not do this. The light exists to protect your engine. Resetting it without performing the service defeats the warning system and can lead to engine damage from running on degraded oil.

What if my key doesn't have a physical ignition slot?

The 2013 Escape uses a traditional key-in-ignition design, not a push-button start. If your Escape has a push-button start, it's a different model year or trim. Consult your owner's manual for the reset procedure specific to your vehicle.

Do I need to go to a Ford dealer to reset the light?

No. The reset procedure is designed for owners to perform themselves and takes about one minute. A dealer can reset it for you, but there's no technical reason to pay for that service.

Will the light come back on when ready after I reset it?

No. After a successful reset, the light should stay off for thousands of miles. If it comes back on within a few days or weeks, there may be an issue with the oil level sensor or the engine itself — have the vehicle scanned for fault codes.

What's the difference between the oil change light and the check engine light?

The oil change light is a maintenance reminder that illuminates on a schedule. The check engine light indicates a fault detected by the engine computer — emissions, sensors, or mechanical issues. They're separate systems. Don't confuse one for the other.