The maintenance light resets after you turn the ignition key or press a button sequence, depending on your model year
The maintenance light on a Toyota Highlander is a reminder that service is due — usually an oil change. Once you've completed the service, the light won't turn off by itself. You need to manually reset it using your dashboard controls or the instrument cluster buttons. The exact steps depend on whether you have a newer model with a touchscreen or an older one with physical buttons.
The process takes less than a minute and requires no tools or special knowledge. You don't need to visit a dealer; you can do it yourself in your driveway after an oil change or any time the light appears and you've confirmed service is complete.
Key Takeaways
- Most Highlanders from 2015 onward use the instrument cluster buttons to reset the maintenance light without starting the engine.
- Older models (2008–2014) require you to turn the ignition key to the "On" position and hold a reset button until the light clears.
- If your Highlander has a touchscreen, you may also reset the light through the vehicle settings menu instead of using buttons.
- Resetting the light does not change your oil or perform any service — it only clears the reminder after you've done the work yourself.
Reset steps for 2015 and newer Highlanders with button controls
On most recent Highlanders, the instrument cluster (the panel behind the steering wheel) has buttons on either side. Turn off the engine and make sure the ignition is in the "Off" position. Look for a button labeled "Trip" or "Reset" on the left or right side of the cluster.
Press and hold the Trip or Reset button until the maintenance light blinks and then disappears. This usually takes 5 to 10 seconds. Release the button once the light is gone. If the light reappears after you start the engine, repeat the process — sometimes it takes two attempts.
Reset steps for 2008–2014 Highlanders
Older Highlanders use a different method. Turn the ignition key to the "On" position without starting the engine. Do not press the brake pedal. Look at the instrument cluster for a small button labeled "Reset" or "Trip Reset," usually located on the left side of the cluster.
Press and hold this button for 10 to 15 seconds until the maintenance light blinks three times and then goes dark. Release the button. Turn the ignition back to "Off." Start the engine to confirm the light has cleared. If it's still visible, repeat the process.
Using the touchscreen menu on newer models
Some newer Highlanders with a central touchscreen also allow you to reset the maintenance light through the vehicle settings menu. Press the "Menu" or "Settings" button on the touchscreen, then navigate to "Vehicle" or "Maintenance." Look for an option labeled "Maintenance Reset" or "Service Reset."
Select it and confirm when prompted. The light should clear when ready. This method is optional — the button method on the instrument cluster works just as well and doesn't require navigating menus.
What to do if the light won't reset
If you've followed the steps and the light remains on after starting the engine, try the reset process one more time. Make sure the ignition is fully off before you begin, and hold the button longer than you think necessary — some models require 15 to 20 seconds.
If the light still won't clear, check your owner's manual for your specific model year, as some Highlanders have variations in button placement or timing. You can also visit a Toyota dealer, who can reset it in seconds at no charge if you've already paid for the service elsewhere. A persistent maintenance light that won't reset sometimes indicates a sensor issue unrelated to the reset procedure itself, in which case a dealer scan can identify the problem.
Resetting after a dealer service
If you had your oil change done at a Toyota dealer, they will reset the light as part of the service. You should not need to do anything. If you pick up your vehicle and the light is still on, ask the service department to reset it before you leave — it takes them seconds and is part of the completed service.
If you had the service done at an independent shop or changed the oil yourself, you are responsible for resetting the light using the steps above. The light is purely a reminder; it does not affect how the vehicle runs.
Frequently Asked Questions
Does resetting the maintenance light mean my oil is changed?
No. Resetting the light only clears the reminder on your dashboard. It does not change your oil or perform any service. You must complete the actual oil change before resetting the light, or the reminder will return when the next service interval arrives.
What if I reset the light by accident before my oil change?
The light will not reappear until the next scheduled service interval (usually 10,000 miles). Write down your current mileage and set a phone reminder for when you need service, so you don't forget. You can also check your owner's manual for the recommended service interval for your model year.
Can I reset the maintenance light while the engine is running?
It depends on your model year. Older Highlanders (2008–2014) require the ignition to be in the "On" position with the engine off. Newer models (2015+) can usually be reset with the engine off or running, though it's easier with the engine off. Check your owner's manual for your specific year if you're unsure.
Is there a way to reset the light from my phone or key fob?
No. Toyota does not offer remote reset of the maintenance light through the key fob or a mobile app. You must use the dashboard buttons or touchscreen menu in the vehicle itself. The process takes less than a minute and requires you to be in the driver's seat.