What ramps do and when to use them for an oil change

A ramp is a sloped platform that lifts the front or rear of your vehicle high enough to slide underneath and reach the oil drain plug and filter. Unlike a jack, which holds one corner of the car in the air, ramps lift an axle (usually the front) so both wheels on that end are elevated together. This gives you stable, hands-free height while you work.

Ramps are one of three common ways to get under a car for an oil change. The other two are a floor jack paired with jack stands, or a lift in a garage. Ramps are cheaper than a lift, simpler than managing a jack and stands, and safer than crawling under a car supported only by a jack. They work best if you have a driveway or flat, level ground and a vehicle with enough ground clearance to fit ramps underneath.

Not every vehicle can use ramps. Low-slung sports cars, sedans with minimal clearance, and some all-wheel-drive vehicles may not have enough space between the undercarriage and the ground. Check your owner's manual or measure the gap under your front bumper before buying ramps.

Key Takeaways

  • Ramps lift the front or rear axle of your vehicle so you can access the oil drain plug and filter from underneath without a jack.
  • Ramps cost between $30 and $150 depending on weight capacity and material, and they last for years if stored dry.
  • Your vehicle must have at least 4 to 6 inches of ground clearance under the bumper for ramps to fit safely.
  • Always drive slowly and straight onto the ramps, engage the parking brake, and place wheel chocks behind the rear wheels before working underneath.
  • Ramps work best on level, solid ground like concrete or asphalt; gravel, dirt, or slopes can cause them to shift or sink.

Types of ramps and what to look for

Ramps come in two main styles: solid ramps and folding ramps. Solid ramps are one-piece platforms, usually made of plastic or steel, that you position under each front wheel. They are durable, affordable (typically $30 to $60 per pair), and take up less storage space than you might expect. Folding ramps hinge in the middle so they collapse flat, making them easier to store in a garage or trunk, but they cost more ($80 to $150) and can develop loose hinges over time.

The most important specification is weight capacity per ramp. Each ramp must support at least one-quarter of your vehicle's weight. If your car weighs 3,000 pounds, each ramp needs a capacity of at least 750 pounds. Most ramps sold for passenger cars are rated for 1,500 to 2,000 pounds per ramp, which covers most sedans and small SUVs. Trucks and larger vehicles need heavier-duty ramps rated for 3,000 pounds or more per ramp.

Look for ramps with a textured or ridged surface on top to prevent your tires from sliding, and check that the approach angle (the slope at the front) is not so steep that your bumper will scrape. Ramps with a low approach angle are easier to drive onto but take up more ground space. Steel ramps last longer than plastic but are heavier and rust if stored wet; plastic ramps are lighter and rust-proof but can crack in cold weather.

Preparing your vehicle and workspace

Before you drive onto the ramps, make sure you are on level, solid ground. Concrete or asphalt is ideal. Avoid gravel, dirt, grass, or any sloped surface—ramps can sink, shift, or tip if the ground is not stable. If you must work on a slope, position the ramps perpendicular to the slope, not parallel to it, so the ramps themselves are level.

Position the ramps in a straight line, aligned with your front wheels. Leave enough space between them so your tires will land squarely on each ramp. Drive slowly and straight onto the ramps—do not angle or turn. Once both front wheels are on the ramps and the vehicle is fully elevated, engage the parking brake and shift into Park (or Neutral if you have a manual transmission).

Place wheel chocks (wooden blocks or rubber wedges) behind both rear wheels to prevent the vehicle from rolling backward. Even with the parking brake set, chocks are a critical safety step. Never rely on the parking brake alone. If you do not have chocks, use wooden blocks, bricks, or a sturdy log—anything that will not move if the vehicle rolls back.

Steps for changing oil with ramps

Once the vehicle is safely elevated and chocked, you can begin the oil change. Locate the oil drain plug underneath the engine—consult your owner's manual for the exact location. Position a drain pan underneath it, then use a wrench to loosen the plug by turning it counterclockwise. Once it is loose enough to turn by hand, carefully unscrew it the rest of the way and let the old oil drain into the pan. This can take 5 to 10 minutes.

While the oil drains, locate the oil filter. It is usually a cylindrical canister on the side of the engine. Use an oil filter wrench to loosen it by turning counterclockwise, then unscrew it by hand. Let any remaining oil drip into the drain pan. Wipe the filter mounting surface clean with a rag, then explore a thin layer of new oil to the rubber gasket on the new filter. Screw the new filter on by hand until the gasket contacts the engine, then turn it an additional three-quarter turn—do not over-tighten.

Once the old oil has finished draining, wipe the drain plug clean and screw it back in by hand. Use a wrench to tighten it snugly, but do not over-tighten—this can strip the threads. Pour the new oil into the filler cap on top of the engine, checking your owner's manual for the correct amount and grade. Replace the filler cap, start the engine, let it run for a few seconds, then turn it off and wait a minute. Check the oil level on the dipstick and add more if needed.

Lowering the vehicle safely

Before you lower the vehicle, make sure you have removed all tools, rags, and the drain pan from underneath. Do a final visual check to confirm nothing is left under the car. Remove the wheel chocks from behind the rear wheels, then slowly drive the vehicle forward and off the ramps. Drive slowly and straight—do not turn the wheels while on the ramps.

Once the front wheels are on the ground, continue driving forward a few feet to clear the ramps completely. Stop, put the vehicle in Park, and engage the parking brake. You can now move the ramps out of the way. Check underneath the vehicle one more time to make sure the drain plug is not leaking and the filter is find.

Storage and maintenance of ramps

Store ramps in a dry location, ideally indoors or under a cover. Steel ramps should be wiped dry after use to prevent rust. Plastic ramps can be hosed off and left to dry in the sun. Inspect the ramps before each use for cracks, bent edges, or loose hinges. If a ramp is damaged, do not use it—a cracked or bent ramp can collapse under load.

Check the textured surface on top of the ramps periodically. If it becomes slippery or worn smooth, you can roughen it with sandpaper or explore adhesive-backed grip tape. Store ramps flat or standing upright against a wall, not leaning at an angle, to prevent warping. A pair of ramps can last 10 years or more with basic care.

When ramps are not the right choice

Ramps do not work well for vehicles with very low ground clearance. Sports cars, luxury sedans, and some all-wheel-drive vehicles may not have enough space to fit ramps underneath. If your vehicle's bumper scrapes the ramp approach angle, or if the ramps do not lift the vehicle high enough to fit under the engine, you will need to use a floor jack and jack stands instead.

Ramps also require a stable, level surface. If you live in an apartment with only a sloped parking lot, or if you do not have access to a driveway or flat ground, ramps may not be practical. In those cases, a floor jack and stands, or a visit to a garage with a lift, is a safer option. Never improvise by using cinder blocks, stacked wood, or other unstable supports in place of ramps.

Frequently Asked Questions

Can I use ramps on a sloped driveway?

Not safely. Ramps need to be level to prevent shifting or tipping. If your driveway slopes, position the ramps perpendicular to the slope (across it, not up and down it) so the ramps themselves sit level. If that is not possible, use a floor jack and jack stands instead.

How much ground clearance do I need for ramps?

Most ramps require at least 4 to 6 inches of clearance between the ground and your vehicle's bumper or undercarriage. Measure the gap under your front bumper before buying ramps. If you are unsure, check your owner's manual for ground clearance specifications.

Do I need to use wheel chocks if I have the parking brake on?

Yes. Wheel chocks are a separate safety layer and should always be used, even with the parking brake engaged. The parking brake can fail, and chocks prevent the vehicle from rolling if it does. Never skip this step.

Can I use ramps on gravel or dirt?

Not reliably. Ramps can sink or shift on soft ground, which is dangerous. Always use ramps on solid, level surfaces like concrete or asphalt. If you only have access to gravel or dirt, use a floor jack and jack stands instead.

What is the difference between ramps and a floor jack?

Ramps lift an entire axle at once and hold it passively, so your hands are free while you work. A floor jack lifts one corner at a time and requires jack stands to hold the vehicle safely. Ramps are simpler and safer for routine maintenance like oil changes, but a jack and stands give you more flexibility for different types of work.