What you need to know before starting
A Ram 1500 oil change takes 30 to 45 minutes if you have the right tools and know where the drain plug sits. The job itself is straightforward: drain the old oil, replace the filter, add new oil, and check the level. You'll need an oil drain pan, a wrench or socket to fit your drain plug, an oil filter wrench, and fresh oil in the weight your truck's manual specifies — not the weight someone online recommends.
The first thing to do is locate your owner's manual or look up your specific model year, because Ram changed the filter location and drain plug design between generations. A 2009 Ram 1500 is not the same as a 2019 Ram 1500. Your manual will tell you the oil capacity, the correct weight, and whether your truck has a cartridge filter (looks like a canister on top of the engine) or a spin-on filter (looks like a can screwed to the side).
If you've never done this before, consider watching a video specific to your model year first — seeing where the drain plug actually is makes the job much faster. The most common mistake is not warming up the engine first, which makes old oil thicker and slower to drain, or over-tightening the new filter, which makes it nearly impossible to remove next time.
Key Takeaways
- Warm your engine for two to three minutes before draining so old oil flows out faster and more completely.
- Your Ram 1500's oil capacity and correct weight are in your owner's manual, not on a sticker under the hood — use those numbers, not guesses.
- Cartridge filters (on top of the engine) and spin-on filters (on the side) require different tools and techniques, so confirm which type you have before you start.
- Hand-tighten the new filter until the rubber gasket touches the engine, then turn it three-quarters of a turn more — over-tightening causes leaks and makes removal harder.
- Check your oil level with the dipstick after the engine has been off for at least five minutes so the oil settles in the pan.
Locating the drain plug and filter on your Ram 1500
The drain plug sits on the bottom of the oil pan, underneath the engine. On most Ram 1500 models, you'll access it from below — you may need to remove a plastic skid plate or belly pan first. The plug is usually a bolt with a washer or crush ring attached. Some newer models have a drain valve instead of a plug, which looks like a small lever or knob you can turn by hand.
The oil filter location depends on your model year. Trucks from 2009 to 2018 typically have a spin-on filter mounted on the driver's side of the engine block, low and toward the front. Newer Ram 1500s (2019 and later) often use a cartridge filter mounted on top of the engine, which looks like a large plastic housing with a cap. Check your manual or search your specific year online to be certain — the difference matters because you'll need different tools and techniques.
If you can't find either one, your owner's manual has a diagram. If you don't have the manual, you can read one free from Ram's website using your VIN, or search "[your year] Ram 1500 oil filter location" and look for forum posts or YouTube videos from owners with the same truck.
Draining old oil and replacing the filter
Start with the engine warm but not hot — run it for a few minutes and then turn it off. Let it sit for one minute so the oil begins to settle. Place your drain pan under the plug, then loosen the plug with a wrench or socket. Once it's loose enough to turn by hand, unscrew it the rest of the way and let it drop into the pan. The oil will be hot, so move slowly and let it drain for at least five minutes. If you have a crush ring on the plug, you'll need a new one when you reinstall it — don't reuse the old ring.
While the oil drains, locate the filter. For a spin-on filter, use an oil filter wrench to loosen it, then unscrew it by hand. Wipe the mounting surface clean with a rag. For a cartridge filter, remove the cap (usually by turning it counterclockwise), pull out the old filter element, and clean the inside of the housing. Either way, explore a thin layer of new oil to the rubber gasket on the new filter or element before installing it.
Screw the spin-on filter on by hand until the gasket touches the engine, then turn it three-quarters of a turn more. Do not use the wrench to tighten it — hand-tight is correct. For a cartridge filter, insert the new element, replace the cap, and tighten it snugly by hand. Reinstall the drain plug and tighten it to the torque spec in your manual (usually 25 to 35 foot-pounds for Ram 1500s, but check yours). If you're using a crush ring, use a new one and don't over-tighten.
Adding new oil and checking the level
Locate the oil filler cap on top of the engine — it usually says "OIL" on it. Unscrew it and set it aside. Pour in the amount of oil your manual specifies, but start with one quart less than the full capacity. This gives you room to check the level without overfilling. Use a funnel to avoid spilling oil on the engine.
Wait at least five minutes after you've finished pouring, then start the engine and let it run for 30 seconds. This circulates the new oil through the filter. Turn the engine off and wait another five minutes for the oil to settle in the pan. Pull out the dipstick, wipe it clean with a rag, reinsert it all the way, then pull it out again and read the level. The oil should be between the minimum and maximum marks. If it's low, add a half-quart and check again.
Once the level is correct, screw the oil filler cap back on. Check under the truck for leaks around the drain plug and filter — a few drops are normal while the engine is still warm, but a steady drip means something is loose. If you see a leak, turn off the engine, let it cool, and tighten the plug or filter a bit more.
Tools and supplies you'll need
An oil drain pan is essential — it catches the old oil so you don't spill it on the ground. A set of wrenches or sockets will fit your drain plug; most Ram 1500s use a 13mm, 14mm, or 15mm socket, but check your manual. An oil filter wrench is necessary for spin-on filters — it's a metal band or cup that grips the filter so you can turn it. You can buy one for $10 to $20 at any auto parts store.
You'll need fresh oil in the correct weight and quantity. Your manual specifies both. Most modern Ram 1500s use 5W-30 or 5W-20, but don't assume — check the manual. Buy a few extra quarts in case you need to top up later. A funnel prevents spills when pouring. A rag or old towel cleans the dipstick and wipes up drips. If your truck has a crush ring on the drain plug, buy a new one before you start — they're cheap and reusing them causes leaks.
If you're working on a newer Ram 1500 with a cartridge filter, you may need a cartridge filter wrench, which looks like a large socket. Some people use a strap wrench instead. Check what your filter housing requires before you buy tools.
Disposing of old oil safely
Never pour old oil down a drain or into the ground — it's illegal in most places and damages soil and water. Most auto parts stores that sell oil will take used oil for free, even if you didn't buy it from them. Bring it in a sealed container or the drain pan you used. Some recycling centers and service stations also accept it.
If you don't have a way to transport it, call ahead to confirm the store takes used oil and ask about their hours. Keep the oil in a clean container so it doesn't spill in your truck. If you spill oil on the ground, cover it with kitty litter or sand to absorb it, then sweep it up and dispose of it as hazardous waste — check your local waste facility for instructions.
When to change your Ram 1500's oil
Ram recommends an oil change every 10,000 miles or 12 months, whichever comes first, for trucks using synthetic oil. If your truck uses conventional oil, the interval is usually 5,000 to 7,500 miles. Check your owner's manual for the exact interval for your model year, because Ram has changed these recommendations over time. Your manual may also have a maintenance schedule that tells you what else to check or replace at each service.
If you drive in severe conditions — towing, idling in traffic, dusty roads, or short trips — you may need to change oil more often. Your manual has a separate severe-use schedule. Keep track of your oil changes by writing the date and mileage in your manual or taking a photo of the odometer after each change.
Frequently Asked Questions
Can I change the oil myself if I don't have a lift or ramps?
Yes. You can work from underneath the truck if you're comfortable lying on your back, or you can drive the front wheels onto a pair of ramps to raise the truck slightly. Ramps cost $30 to $50 and are safer than using a jack alone. Never work under a truck supported only by a jack — use jack stands or ramps.
What if I can't find the drain plug or filter?
read your owner's manual from Ram's website using your VIN, or search YouTube for "[your year] Ram 1500 oil change" and watch someone do it on your exact model. If you're still stuck, call a local Ram dealer or independent shop and ask where the drain plug is — they can usually tell you in one minute.
How do I know if I overfilled the oil?
If the dipstick reads above the maximum mark, the engine has too much oil. Drain a quart into a clean pan, wait five minutes, and check the level again. Overfilled oil can damage the engine, so don't ignore it.
Do I need to replace the crush ring on the drain plug every time?
Yes, if your truck has one. A crush ring is a soft metal washer that seals the drain plug. Reusing it causes leaks. They cost less than a dollar, so buy new ones with your oil.
What should I do with the old oil filter?
Drain any remaining oil from the old filter into your drain pan, then take it to an auto parts store or recycling center. Some stores accept old filters for free. Do not throw it in the trash.