The oil filter tray catches drips when you change your oil so they don't end up on your garage floor or driveway

An oil filter tray is a shallow metal or plastic pan that sits underneath your motorcycle's oil filter during an oil change. When you unscrew the old filter, oil drains out—sometimes a cup or more, depending on your bike's design. Without a tray, that oil runs straight onto whatever surface is below: concrete, asphalt, your garage floor. With a tray in place, the oil collects inside it so you can dispose of it safely and keep your space clean.

The tray is not part of your motorcycle itself. It is a tool you use during maintenance, much like a wrench or a drain pan. Most riders either buy one or improvise with a shallow container. Some motorcycles have the filter positioned so that oil drips straight down; others angle it sideways, which makes a tray even more necessary to catch the flow.

Oil disposal matters because used motor oil is a hazardous waste in most places. Pouring it down a drain or leaving it on the ground is illegal and damages soil and water. A tray makes it straightforward to collect the oil, pour it into a container, and take it to a recycling center or auto parts store—most accept used oil for free or a small fee.

Key Takeaways

  • An oil filter tray is a shallow pan that catches dripping oil when you remove your motorcycle's filter, preventing spills on your floor or driveway.
  • The tray is a maintenance tool you supply yourself, not a part of the motorcycle, and most riders buy one or use a shallow container as a substitute.
  • Used motor oil must be disposed of as hazardous waste, and a tray makes collection and transport to a recycling center or auto parts store straightforward.
  • Filter position varies by motorcycle model, so check your owner's manual or do a test run to see how much oil drains and in which direction.
  • A tray typically costs between $10 and $30 and lasts for years, making it one of the cheapest tools to own if you change your own oil.

How much oil actually drains from the filter

The amount of oil that comes out when you unscrew the filter depends on how much oil is trapped inside the filter itself and how long the filter has been sitting. On most motorcycles, expect between 0.5 and 1.5 quarts of oil to drain when you remove the filter. Larger bikes with bigger filters may release closer to 2 quarts. Smaller bikes and scooters might release only a quarter quart or so.

The flow is not always straight down. Many motorcycle filters are mounted horizontally or at an angle, which means oil runs sideways or diagonally as it drains. This is why a tray that is too small or positioned incorrectly can miss the drip. Before you start, look at where your filter sits and imagine the path the oil will take. If your filter points downward at a steep angle, a vertical tray works. If it angles to the side, you need a wider, shallower pan.

The first few seconds of drainage are the heaviest. Oil pours out quickly at first, then slows to a trickle. If you are not ready with the tray, you will miss the bulk of it. Have your tray positioned and ready before you crack the filter loose.

Choosing or building an oil filter tray for your motorcycle

You can buy a purpose-built motorcycle oil filter tray from most auto parts stores or online retailers. These are typically aluminum or heavy-duty plastic, shaped like a shallow rectangle or oval, and cost between $10 and $30. They often have a pouring spout on one side so you can direct the collected oil into a container without splashing. Some come with a handle for easier carrying.

If you do not want to buy one, you can use any shallow container: a baking pan, a low plastic storage tub, or even a large aluminum takeout container. The only requirement is that it is wide enough to catch the drip pattern and deep enough to hold the oil without overflowing. Test it once before you rely on it—position it under the filter, loosen the filter slightly to let a little oil out, and watch where it goes. Adjust the tray position if needed.

Some riders use a combination approach: they buy a small tray for regular use but keep a larger, deeper pan nearby as a backup in case the filter is more full than expected. This is practical insurance, especially if you are working in a garage or driveway where a spill would be costly to clean up.

Where to position the tray under your filter

Position matters more than you might think. The tray should sit directly underneath the filter, centered on the drip path. If your filter points straight down, center the tray below it. If the filter angles to one side, shift the tray so the oil will land in the middle of the pan, not at the edge where it might splash out.

Leave a little clearance between the tray and the filter itself—usually 2 to 3 inches is enough. You need room to grip the filter wrench and turn it. If the tray is too close, you will bang your knuckles or the wrench against it. If it is too far away, oil will miss the pan and hit the floor instead.

On some bikes, the filter is tucked in a tight spot where a standard rectangular tray will not fit. In those cases, a smaller or oval-shaped tray works better. Check your owner's manual or look at photos of other riders doing the same oil change on your model to see what works best.

Disposing of the oil you collect

Once the tray is full or nearly full, you need to transfer the oil to a container for disposal. Use a funnel and a clean, sealable container—an old motor oil jug, a plastic milk jug, or any container that will not leak. Pour slowly to avoid splashing. If you spill any oil, wipe it up when ready with rags or paper towels and dispose of those as hazardous waste as well.

Take the sealed container to a local auto parts store, quick-lube shop, or municipal hazardous waste collection site. Most auto parts chains—Autozone, O'Reilly, NAPA, and others—accept used motor oil for free, no purchase necessary. Some municipalities run collection days or permanent drop-off centers. Call ahead or check online to find the nearest location and confirm their hours.

Never pour used oil down a drain, into the ground, or into a storm drain. It is illegal in most places and contaminates groundwater and soil. The disposal process is free or nearly free, so there is no reason not to do it right.

Keeping your tray clean between oil changes

After you pour the oil out, rinse the tray with a hose or in a sink. Dry it with a rag. Store it in a garage or shed where it will not collect dust or debris. A clean tray is easier to use and lasts longer.

If oil hardens or becomes sticky inside the tray, soak it in warm soapy water for a few minutes, then scrub with a brush or cloth. Dry it thoroughly before storing. Do not use harsh solvents or put the tray in a dishwasher unless the manufacturer says it is safe—some plastics can crack or warp.

A well-maintained tray will last for years and pay for itself many times over in saved cleanup time and floor damage prevention.

Frequently Asked Questions

Can I reuse the same tray for multiple oil changes without emptying it?

Yes, but only if the tray is large enough to hold all the oil from several changes without overflowing. Most riders empty the tray after each change to keep it clean and to avoid confusion about how much oil has accumulated. Emptying also lets you dispose of the oil promptly rather than storing it.

What if my motorcycle's filter is in a spot where a tray will not fit?

Use a smaller tray, an oval-shaped one, or a custom container that matches the space. Some riders use a tall, narrow container or even hold a rag underneath the filter to catch the initial heavy drip, then switch to a tray for the slower trickle. Check forums or YouTube videos for your specific bike model to see what other riders use.

Do I need a special tray or can any shallow pan work?

Any shallow pan works as long as it is wide enough to catch the drip and deep enough to hold the oil without spilling. A baking pan, plastic storage container, or old metal tray from around your house will do the job. A purpose-built motorcycle tray is convenient and often has a pouring spout, but it is not required.

How do I know if my tray is positioned correctly before I loosen the filter?

Do a test run: loosen the filter just enough to let a small amount of oil seep out, watch where it lands, and adjust the tray if needed. Then tighten the filter back up, reposition the tray, and proceed with the full removal. This takes 30 seconds and prevents a mess.