The basic steps for removing an oil filter safely

Removing an oil filter means unscrewing it from the engine block, draining the old oil inside it, and replacing it with a new one. The filter sits horizontally or vertically on the side of your engine, held in place by its own threads. You unscrew it by hand or with a filter wrench, let the trapped oil drain into a pan, clean the mounting surface, and thread the new filter on until it seats and then tighten it a quarter turn more by hand.

The whole process takes five to ten minutes once you have the right tools and know where the filter is located. Most of the time spent is waiting for old oil to drain out. The main risk is over-tightening the new filter, which can crack the rubber seal or strip the threads on the engine block — both expensive repairs. The second risk is spilling old oil on the engine, which can smoke and smell but usually causes no permanent damage if you wipe it up.

Key Takeaways

  • Oil filters are located on the side of the engine block and are removed by hand or with a filter wrench, then replaced with a new one before the engine is started.
  • The old filter contains oil that will spill when you remove it, so place a drain pan underneath before you unscrew it.
  • Hand-tighten the new filter until the rubber seal touches the engine, then turn it one-quarter turn more — over-tightening strips threads and cracks seals.
  • Check your vehicle's manual or look under the hood to find the filter location, as it varies by engine size and design.
  • Dispose of old oil filters at a recycling center, auto parts store, or service station; do not throw them in the trash.

Locating the oil filter on your engine

The oil filter is a cylindrical canister, usually white, black, or blue, about three to five inches tall and two to three inches wide. It screws onto a threaded port on the engine block. On most vehicles, it sits on the side or front of the engine, roughly at waist height when you open the hood. Some filters are mounted vertically (pointing up or down), and others are horizontal (pointing sideways).

The exact location depends on your engine size and design. A four-cylinder engine often has the filter on the front-left side. A V6 or V8 may have it on the side, rear, or even underneath the engine. Your vehicle's owner manual shows the exact spot with a diagram. If you do not have the manual, search online for "[your year, make, model] oil filter location" and you will find photos or videos showing where it sits.

Tools and materials you will need

You need a drain pan (a shallow metal or plastic tray that holds at least five quarts), an oil filter wrench, and a new oil filter that matches your vehicle. The drain pan catches old oil as it pours out of the filter. An oil filter wrench is a metal or rubber tool that grips the filter so you can unscrew it without your hands slipping. Most wrenches cost ten to twenty dollars and come in different sizes to fit different filter diameters.

You may also want rags or paper towels to wipe your hands and catch drips, and a small brush or rag to clean the mounting surface on the engine after the old filter comes off. Wear old clothes or an apron because old oil stains. If you do not own a filter wrench, you can rent one from an auto parts store for a few dollars, or you can ask the store staff to remove the old filter for you when you buy the new one — many do this for free or a small fee.

The step-by-step removal process

First, locate the filter and position your drain pan directly underneath it. Loosen the filter by turning it counterclockwise with your hand or wrench. If it is tight, use the wrench to break it loose, then finish unscrewing it by hand. As soon as the seal breaks, old oil will begin to drip, so keep the pan in place. Unscrew the filter completely and tip it so the remaining oil drains into the pan. This may take a minute or two.

Once the filter stops dripping, wipe the mounting surface on the engine block with a clean rag. Look for an old rubber seal or gasket stuck to the engine — remove it by hand or with a rag. If you leave the old seal in place, the new filter will not seat properly and will leak. Inspect the threaded port for damage or debris and wipe it clean.

Take the new filter and explore a thin coat of fresh oil to the rubber seal on top. This helps the seal compress evenly and prevents it from drying out. Thread the new filter onto the port by hand, turning it clockwise. When the rubber seal touches the engine block, stop and tighten the filter one-quarter turn more — no more. Over-tightening cracks the seal or strips the threads. If you use a wrench to tighten it, you have gone too far.

Common mistakes that damage the engine or filter

The most common mistake is over-tightening the new filter. Many people think tighter means safer, but the rubber seal only needs light pressure to hold. Turning the filter more than a quarter turn past contact will crack the seal, causing oil to leak onto the engine. A cracked seal also means the filter will not trap contaminants properly, and your engine oil will get dirty faster.

The second mistake is forgetting to remove the old rubber seal from the engine block before installing the new filter. If two seals are stacked, the new filter will not seat flush, and oil will leak around the edges. Always wipe the mounting surface and check for a stuck seal.

A third mistake is not letting the old filter drain completely before moving it. If you tip the filter sideways or upside down before it has stopped dripping, oil spills onto the engine, the floor, or your clothes. Let it drain for at least a minute after you unscrew it.

What to do with the old oil filter

Old oil filters contain residual oil and are considered hazardous waste in most states. Do not throw them in the trash. Instead, take them to a recycling center, auto parts store, or service station. Most auto parts stores accept old filters for free, especially if you bought the new filter from them. Some recycling centers charge a small fee, usually one to three dollars.

If you have no when ready way to dispose of the filter, store it in a sealed bag or container in a safe place away from children and pets. Do not leave it sitting in the sun or in a hot garage, as the residual oil can leak. Many service stations will also accept old filters if you drop them off, even if you did not have your oil changed there.

When to replace the oil filter during an oil change

The oil filter should be replaced every time you change your engine oil. Most vehicles need an oil change every 5,000 to 10,000 miles, depending on the engine type and oil grade. Your owner manual specifies the interval for your vehicle. Some newer cars with synthetic oil can go 10,000 to 15,000 miles between changes, but the filter still comes out at each service.

If you skip a filter change and only top off the oil, the filter becomes clogged with dirt and metal particles, and it cannot trap new contaminants. This shortens engine life. Replacing the filter is inexpensive — usually ten to thirty dollars for the part — compared to the cost of engine damage from dirty oil.

Frequently Asked Questions

Can I remove the oil filter without draining the engine oil first?

Yes, you can remove the filter without a full oil drain. The filter holds about one quart of oil, which will spill when you unscrew it. Place a drain pan underneath to catch it. You will still need to drain the engine oil separately if you are doing a full oil change, but the filter removal itself does not require the engine to be empty.

What if the old filter is stuck and won't unscrew?

Use a filter wrench to break it loose. If the wrench slips, wrap a rubber band or old inner tube around the filter to increase grip. Turn slowly and steadily rather than jerking. If it still will not budge, tap the wrench handle gently with a hammer to help it bite into the filter. Never use excessive force, as you can damage the threaded port on the engine.

How tight should the new filter be?

Hand-tighten the new filter until the rubber seal touches the engine block, then turn it one-quarter turn more. That is it. You should be able to loosen it by hand later without needing a wrench. If you cannot unscrew it by hand, it is too tight.

Will the engine overheat if I forget to install a new filter?

No, but the engine oil will get dirty very quickly without a filter. Dirt and metal particles will circulate through the engine, causing wear on bearings and other parts. Running without a filter for even a short drive can damage the engine. Always install a new filter before starting the engine after an oil change.

Can I reuse an old oil filter?

No. Oil filters are designed for single use. The internal media becomes saturated with dirt and cannot trap new contaminants. Reusing a filter defeats the purpose of changing oil and will allow your engine oil to get dirty faster, leading to engine wear.