The basic steps to unscrew and remove your oil filter
An oil filter unscrews by hand once you locate it on the engine block. You turn it counterclockwise until it comes free, then pull it straight away from the mounting surface. The filter will be full of old oil, so expect it to drip—place a drain pan or old towels underneath before you start. The whole removal takes about two minutes once you know where to find it.
The hardest part is usually reaching the filter. On many cars it sits on top of the engine or on the side facing the wheel well, but on some it's tucked underneath or behind other components. Your owner's manual shows the exact location. If you can't see it after looking at the manual, a mechanic's creeper (a low wheeled board) lets you slide under the car to check the underside without lying flat on your back.
Key Takeaways
- An oil filter unscrews counterclockwise by hand and should come free with moderate pressure—if it won't budge, use a filter wrench rather than forcing it.
- The filter contains old oil that will spill, so position a drain pan or towels underneath before you begin removal.
- After the filter comes off, wipe the mounting surface clean with a rag so the new filter seals properly.
- The rubber gasket on the old filter should come off with it; if it stays stuck to the engine, remove it by hand before installing the new one.
Locating the oil filter on your specific car
The filter's location depends on your engine layout and model year. On most cars built in the last 20 years, it sits on the top or upper side of the engine block, often with a black plastic cap or a metal canister visible from above. On some Toyotas, Hondas, and other imports, it's mounted vertically on the side of the block. On rear-wheel-drive cars and trucks, it may be on the underside of the engine, which means you'll need to get under the vehicle.
Your owner's manual includes a diagram showing the filter location and sometimes a photo. If you don't have the manual, search the vehicle's year, make, and model online along with "oil filter location"—you'll find photos and videos showing exactly where it sits. Once you've found it once, you'll recognize it when ready next time.
Using a filter wrench when the filter won't turn by hand
A stuck filter usually means the previous filter was installed too tight or the rubber gasket has dried and bonded to the engine. Trying to force it by hand risks stripping the filter or cutting your knuckles on the engine block. A filter wrench solves this problem. The two most common types are the strap wrench (a fabric band with a handle that grips the filter) and the socket wrench (a cup-shaped tool that fits over the filter end).
Strap wrenches work on almost any filter size and are gentler on the filter itself. Socket wrenches are faster but only work if the filter's top is accessible and not dented. Both cost between $8 and $20 and are worth keeping in your toolbox. Attach the wrench, turn counterclockwise slowly, and stop if you feel the filter beginning to crack or collapse—that means you need a different wrench size or approach.
Preventing oil spills and protecting the engine bay
Oil from the filter will drip onto whatever is below it. Place a drain pan, shallow baking pan, or several layers of old towels directly under the filter before you loosen it. As you unscrew the filter, tilt it slightly so the opening faces downward into the pan. Once the filter is free, hold it level or tilted down as you pull it away from the engine—this keeps oil from running down your arm or onto the engine block.
If oil does spill on the engine, wipe it up with a rag before you start the engine. Oil on hot engine parts can smoke and create a burning smell, though it won't damage anything. For the mounting surface itself, use a clean rag or paper towel to wipe away old oil and debris. A small amount of residual oil is fine, but you want the surface clean enough that you can see the rubber gasket seat clearly.
Removing the old rubber gasket stuck to the engine
The rubber gasket is a thin ring glued to the top of the filter. When you unscrew the filter, the gasket usually comes off with it. However, sometimes the gasket stays stuck to the engine block's mounting surface. If this happens, you must remove it before installing the new filter—installing a new filter on top of an old gasket creates a double seal that prevents oil from flowing properly and can cause the engine to run without adequate lubrication.
To remove a stuck gasket, use your fingernail or a plastic scraper to peel one edge up, then pull it off by hand. It should come away easily once you get a grip on it. If it's truly bonded, a small amount of penetrating oil (like WD-40) sprayed on the edge and left for a few minutes will loosen it. Wipe the mounting surface clean with a rag afterward so the new gasket can seal properly.
What to do with the old filter after removal
An old oil filter contains used engine oil and should not go in the trash. Most recycling centers and auto parts stores accept used filters for free. Some will take them even if you didn't buy the new filter from them. Call ahead to confirm they accept filters, or ask your mechanic to dispose of it if you're having the oil change done professionally.
If you're storing the filter temporarily before recycling, place it in a plastic bag or container to catch any remaining oil. A filter can drip for hours after removal, so don't leave it sitting on your garage floor or driveway. Keeping it in a bag prevents stains and keeps the oil contained.
Common mistakes that damage the engine or create leaks
The most common mistake is installing a new filter without removing the old gasket. This creates a double seal that traps oil and prevents proper circulation. Another mistake is over-tightening the new filter during installation—the gasket only needs to compress once, so hand-tight is correct. Over-tightening makes the next filter removal harder and can crack the filter or damage the mounting threads.
A third mistake is forgetting to wipe the mounting surface clean. Dirt or old gasket material prevents the new gasket from sealing, which causes slow leaks that drip oil onto the ground. Finally, some people install the filter upside down or at an angle. The filter should screw straight on and sit flush against the engine block with no gap between the filter base and the mounting surface.
Frequently Asked Questions
How tight should I screw the new filter on?
Hand-tight is correct. Screw it on until the rubber gasket touches the mounting surface, then turn it an additional three-quarters of a turn. The gasket compresses slightly and creates a seal. Over-tightening doesn't improve the seal and makes removal harder next time.
What if oil keeps dripping after I remove the filter?
Some oil will drip for a few minutes after removal—this is normal. If it drips for more than 10 minutes, the filter may have been installed at an angle or the gasket may still be stuck to the engine. Check that the gasket came off with the old filter and that the mounting surface is clean before installing the new one.
Can I remove the filter without draining the oil first?
Yes. The filter removal and the oil drain are separate steps. You can remove the filter without opening the drain plug, though you'll still get oil spills from the filter itself. Most people do both at the same time during an oil change to avoid handling the filter twice.
Is it normal for the filter to be hot?
Yes, especially if you just drove the car. The filter sits against the engine and heats up during operation. Let the engine cool for at least five minutes after driving before you remove the filter, or wear a work glove to protect your hand from the heat.