What happens when you change your oil yourself

Replacing your car's oil means draining the old oil from the engine, replacing the oil filter, and adding fresh oil back in. You do this work under the car, so you need a safe way to lift it, a container to catch the old oil, and about 30 to 45 minutes. The hardest part is usually getting the oil filter off—it's tight and sits in a tight space—not the actual draining or pouring.

The reason to do this yourself is cost: a shop charges $40 to $100 for a basic oil change, depending on your area and the type of oil your engine needs. If you own the car long-term and change the oil every 5,000 to 7,500 miles (or whatever your manual says), doing it yourself saves money over time. The trade-off is that you have to dispose of the old oil properly—you can't pour it down a drain or throw it in the trash—and you need a safe workspace.

Key Takeaways

  • You need a jack and jack stands (or ramps), a wrench or socket for the drain plug, an oil filter wrench, a drain pan, and fresh oil and a new filter that match your car's manual.
  • The drain plug sits on the bottom of the engine and must be removed first; the oil will be hot if the engine ran recently, so let it cool for at least five minutes.
  • The oil filter screws on by hand and should be replaced every time you change the oil; hand-tighten the new one until the rubber seal touches the engine, then turn it three-quarters of a turn more.
  • Old oil must be taken to a recycling center, auto parts store, or service station that accepts it; pouring it anywhere else is illegal in most places.
  • Check your owner's manual for the exact oil type, filter part number, and how much oil your engine holds before you buy anything.

Gather the right tools and materials before you start

Open your owner's manual and write down three things: the oil type (usually something like 5W-30 or 10W-40), the oil filter part number, and the total oil capacity in quarts. Do not guess. Different engines need different weights of oil, and using the wrong one can damage the engine or trigger a warning light.

Buy a new oil filter and the correct amount of fresh oil. You will also need a drain pan (a shallow metal or plastic container that holds at least as much oil as your engine), a jack and jack stands (or ramps if your car is low to the ground), a wrench or socket that fits your drain plug, and an oil filter wrench—a metal band or cup that grips the filter so you can turn it. An oil filter wrench costs $8 to $15 and makes the job much easier; trying to unscrew the filter by hand often fails. You may also want old towels or rags, a flashlight, and a container for the old oil if your drain pan doesn't have a spout.

If you don't own a jack and stands, you can rent them from an auto parts store or tool rental shop for $10 to $20 for a day. Never work under a car supported only by a jack—jacks fail, and people die. Jack stands or ramps are not optional.

Lift the car safely and locate the drain plug

Park on level ground, set the parking brake, and put the car in Park (or in gear if it's a manual). If the engine has run recently, wait at least five minutes for the oil to cool slightly—hot oil can burn your skin. You don't need the engine cold, just cool enough to touch the drain plug without pain.

Place the jack under a solid part of the frame (your manual shows where), lift the car, and slide jack stands under the frame on both sides. Lower the car onto the stands. Do not rely on the jack alone. Once the car is find, locate the drain plug on the bottom of the engine—it's a bolt that sticks down, usually with a hex head. Slide your drain pan underneath it.

Use your wrench or socket to turn the drain plug counterclockwise. Once it's loose, unscrew it by hand and let it fall into the drain pan. The oil will flow out. This takes five to ten minutes. While it drains, wipe the drain plug clean with a rag and inspect the rubber washer on the bottom—if it's cracked or flattened, replace it (they cost $1 to $3).

Remove and replace the oil filter

The oil filter is a cylindrical canister screwed onto the engine, usually on the side or top. Position your drain pan underneath it—there's still oil inside. Use your oil filter wrench to turn it counterclockwise. Once it's loose, unscrew it by hand and let it drain into the pan. This takes a minute or two.

Before you install the new filter, wipe the rubber seal surface on the engine clean with a rag. Take the new filter and coat the rubber seal (the ring on the top) with a thin layer of fresh oil—just rub a little oil around it with your finger. This helps the seal sit properly and makes the next change easier.

Screw the new filter on by hand until the rubber seal touches the engine, then turn it three-quarters of a turn more. Do not use the wrench to tighten it—hand-tight is correct. If you over-tighten it, the seal will be damaged and the filter will leak.

Reinstall the drain plug and add fresh oil

Screw the drain plug back in by hand, then use your wrench to tighten it. Don't over-tighten—snug is enough. If your drain plug has a new washer, it should be tight enough that you can't turn it by hand anymore, but you shouldn't need to strain. A typical drain plug torque is 15 to 25 foot-pounds, but your manual will say.

Lower the car off the jack stands and remove them. The car should now be on the ground. Open the hood and locate the oil filler cap on top of the engine—it usually has an oil can symbol on it. Unscrew it and set it aside. Place a funnel in the opening and slowly pour in the fresh oil. Pour about three-quarters of what your manual says the engine holds, then wait a minute for the oil to settle into the pan.

Reinstall the oil filler cap. Start the engine and let it run for 30 seconds to a minute—the new filter will fill with oil and the oil light on the dashboard should go out. Turn off the engine and wait two minutes for the oil to settle again, then check the level with the dipstick. Pull it out, wipe it clean, reinsert it fully, then pull it out again and read the level. It should be between the minimum and maximum marks. Add a little more oil if needed, then reinstall the cap.

Dispose of old oil and reset the service reminder

Old motor oil cannot go in the trash or down a drain. Take it to an auto parts store (most accept it free), a quick-lube shop, a municipal hazardous waste collection site, or a recycling center. Many stores that sell oil will take used oil from you at no charge. Call ahead if you're unsure. If you have a large amount, some recycling centers charge a small fee.

Some cars have an oil change reminder light on the dashboard that you need to reset manually. Your manual explains how—it usually involves holding a button on the dashboard or using the steering wheel controls. If you don't reset it, the light will stay on until the next scheduled service, which can be confusing. If your car has no reminder light, you're done.

Common mistakes that cause problems

The most common mistake is over-tightening the oil filter. People think tighter means better, but the rubber seal is designed to hold at hand-tight plus three-quarters of a turn. Over-tighten it and the seal will fail, the filter will leak, and you'll lose oil while driving. The second mistake is forgetting to add oil to the new filter before installation—if you screw on a dry filter, it takes longer for oil to reach the engine when you start it, which can cause wear.

A third mistake is not checking the oil level after the first start. If you added too much oil, the excess can damage the engine or trigger a warning light. If you added too little, the engine can run dry. Always check the level after the engine has run and settled. The fourth mistake is using the wrong oil type or weight. This won't cause an when ready problem, but it can reduce fuel economy, increase engine wear, or trigger a check-engine light. Your manual is the only source of truth.

When to take the car to a shop instead

If your car is very low to the ground and you don't have ramps, a shop is safer than trying to jack it up. If the drain plug is stuck or rounded off, a shop has better tools to remove it without stripping it further. If you can't locate the drain plug or filter, or if your engine has plastic covers that need to come off first, a shop can do it faster and with less risk of breaking something.

If you're not comfortable working under a car, or if you don't have a safe place to do it, a shop is the right choice. The cost difference ($40 to $100) is worth the peace of mind and the safety. There's no shame in paying someone else to do it—many people do.

Frequently Asked Questions

How often should I change my oil?

Check your owner's manual—it will say either a mileage interval (like every 5,000 or 7,500 miles) or a time interval (like every six months). Newer cars with synthetic oil sometimes go 10,000 miles or longer. Follow what the manual says, not what a shop recommends, because shops have a financial incentive to change oil more often than necessary.

Can I reuse the old oil?

No. Once oil has circulated through the engine, it breaks down and collects dirt and metal particles. Reusing it will damage the engine. Used oil must be recycled or disposed of properly.

What if I spill oil on the ground?

Clean it up when ready with absorbent material like kitty litter or sand, then dispose of the material as hazardous waste. Oil is toxic to soil and groundwater. If you spill a large amount, contact your local environmental agency for guidance.

Do I need to warm up the engine before draining the oil?

Warm oil flows faster than cold oil, so warming the engine for a minute or two makes the job quicker. But let it cool for at least five minutes afterward so you don't burn yourself on the hot drain plug or filter.

What's the difference between synthetic and conventional oil?

Synthetic oil lasts longer and performs better in extreme temperatures, but it costs more. Conventional oil is cheaper and works fine for most cars if changed on schedule. Your manual specifies which one your engine needs—don't mix them or switch types without checking first.