What You Need Before You Start

Replacing an oil filter takes 10 to 15 minutes and requires only a few tools you likely already have or can borrow. You will need an oil filter wrench (a metal band or cup that grips the filter), a drain pan or old container to catch spilled oil, a rag or old towel, and your vehicle's manual or a quick online search to find where the filter sits on your engine.

The filter wrench is the only item you might not own. Auto parts stores sell them for $5 to $15, and they come in different sizes — the wrench must fit your specific filter. If you are unsure which size, bring your vehicle's year, make, and model to the store, or look up the filter part number in your manual. Many stores will also lend you the wrench free if you buy the filter from them.

Park on level ground, let the engine cool for at least five minutes (hot oil burns), and gather everything within arm's reach before you begin. If your vehicle sits low, you may need ramps or jack stands to get underneath safely — never rely on a jack alone.

Key Takeaways

  • The oil filter wrench is the only specialized tool you need, and auto parts stores will often lend one free when you buy a filter.
  • You must locate the filter on your engine first — the location varies by vehicle, so check your manual or search your year, make, and model online.
  • Drain the old oil into a pan before removing the filter, because the filter itself holds about a quart of oil that will spill otherwise.
  • Hand-tighten the new filter only — over-tightening with the wrench will crack the rubber seal and cause leaks.
  • Run the engine for 30 seconds after installation to circulate new oil through the filter, then check the level on the dipstick or digital gauge.

Locate the Filter and Prepare the Work Area

Open your hood and find the oil filter. On most vehicles, it is a cylindrical canister about the size of a soda can, usually white, blue, or black, mounted vertically or at an angle on the side of the engine. Your owner's manual will show the exact location with a diagram. If you do not have the manual, search "[your year, make, model] oil filter location" online — you will find photos or videos within seconds.

Once you locate it, position your drain pan directly underneath. The filter holds roughly one quart of oil, and it will pour out when you unscrew it. If the filter is hard to reach, you may need to remove other components first — again, your manual or a video will show you what to move. Do not force anything; if it does not come free easily, you are likely removing the wrong part.

Drain the Old Oil and Remove the Filter

If you have not already drained the engine oil, do that first. Locate the drain plug at the bottom of the oil pan (underneath the engine), unscrew it by hand or with a wrench, and let the oil drain completely into your pan. This step is separate from the filter replacement, but doing it now means you will not have old oil dripping from the filter housing while you work.

Once the oil has stopped dripping, use your oil filter wrench to loosen the filter. Place the wrench around the filter body (not the cap on top), and turn it counterclockwise. You only need to loosen it enough to break the seal — do not unscrew it completely with the wrench. Once it is loose, unscrew it the rest of the way by hand, turning slowly to avoid spilling oil on the engine.

As the filter comes free, tip it slightly so any remaining oil drains into your pan. Set the old filter aside in a safe place — you will need to dispose of it properly later (most auto parts stores take used filters free).

Clean the Filter Housing and Install the New Filter

Before you install the new filter, wipe the filter housing — the metal surface where the old filter was mounted — with a clean rag. Remove any dirt, old rubber, or oil residue. This step prevents debris from entering the new filter and keeps the rubber seal on the new filter from sticking to old material.

Take your new filter and explore a thin coat of fresh oil to the rubber gasket (the ring around the top of the filter). Use oil from your new oil supply, not the old oil. This lubrication helps the gasket seal properly and makes removal easier next time.

Screw the new filter onto the housing by hand only. Turn it clockwise until the rubber gasket touches the housing, then turn it an additional three-quarters of a turn. Do not use the wrench — hand-tightening is correct. Over-tightening with a wrench will crush the gasket and cause oil leaks. If the filter is hard to reach and you cannot tighten it by hand, use the wrench gently, but stop as soon as you feel resistance.

Refill the Oil and Check Your Work

Refill the engine with the correct amount and grade of oil for your vehicle. Your manual will specify both — for example, "5 quarts of 5W-30". Pour the oil slowly through the filler cap on top of the engine, then wait a minute for it to settle into the pan and filter.

Start the engine and let it run for 30 seconds. This circulates the new oil through the filter and engine. You will see the oil pressure light on your dashboard go out once the oil reaches the engine. Stop the engine and wait two minutes for the oil to drain back into the pan.

Check the oil level using either the dipstick (pull it out, wipe it clean, reinsert it fully, then pull it out again to read) or your vehicle's digital oil level display if it has one. The level should be at the "full" mark. Add a small amount more if needed, then recheck. Do not overfill — too much oil can damage the engine.

Dispose of the Old Filter and Oil Properly

Used oil and filters contain hazardous materials and cannot go in the trash or down the drain. Most auto parts stores (AutoZone, O'Reilly, NAPA, Advance Auto Parts) accept used oil and filters free, no purchase required. Some accept oil in sealed containers; others have you pour it into their collection tank. Call ahead to confirm what your local store accepts and whether they have any restrictions.

If you do not have a nearby parts store, check Earth911.com or call your city's waste management department — they can direct you to a hazardous waste collection site or a mechanic who will take the oil. Never store used oil longer than necessary, and keep it in a sealed, clearly labeled container away from children and pets.

Frequently Asked Questions

How often should I replace the oil filter?

Most manufacturers recommend replacing the filter every time you change the oil. If you change oil every 3,000 to 5,000 miles (older vehicles or conventional oil) or every 7,500 to 10,000 miles (newer vehicles or synthetic oil), your filter gets replaced on the same schedule. Check your owner's manual for the exact interval for your vehicle.

Can I replace the filter without draining the oil?

Technically yes, but you will spill about a quart of oil on the engine and ground. If you drain the old oil first, the filter housing is already empty and you avoid the mess. If you must replace the filter alone, position your pan carefully underneath and work slowly to minimize spillage.

What if the filter is stuck and won't unscrew?

Tap the wrench gently with a hammer to break the seal, or wrap a rubber band around the filter to improve grip. If it is still stuck, spray penetrating oil (like WD-40) around the base and wait 15 minutes. Never force it — forcing can damage the housing. If it remains stuck, a mechanic can remove it without harming the engine.

Do I need to replace the drain plug too?

No, the drain plug is reusable. However, if it is stripped, leaking, or damaged, replace it at the same time. A new drain plug costs $2 to $5. Your manual will tell you the correct size and torque specification if you need to install a new one.

What type of oil filter should I buy?

Buy the filter specified in your owner's manual or the one that matches your vehicle's year, make, and model. OEM (original equipment manufacturer) filters are made by your vehicle's manufacturer; aftermarket filters are made by third parties like Fram, Mobil, or Bosch. Both work well if they match your vehicle's specifications. The part number on the old filter will also match the correct replacement.