The basic process: drain, replace the filter, add new oil
An oil change means removing the old oil from your engine, replacing the oil filter, and filling the engine with fresh oil. You do this by locating the drain plug underneath the engine, unscrewing it to let the old oil drain into a pan, removing and replacing the filter, then pouring new oil through the filler cap on top of the engine. The whole job takes 30 minutes to an hour if you have done it before, longer if this is your first time.
You will need the right type and amount of oil for your car — check your owner's manual or the label under the hood for the viscosity grade (like 5W-30) and the capacity in quarts. You will also need an oil filter that matches your engine, an oil drain pan, a wrench or socket to fit your drain plug, an oil filter wrench, and rags or paper towels. A jack and jack stands are necessary if you need to get under the car to reach the drain plug.
The job is straightforward enough that many car owners do it themselves, but it requires you to work safely under or around the vehicle and to dispose of old oil properly. If you are not comfortable with any part of the process, a shop can do it for $30 to $75 in labor, plus the cost of oil and filter.
Key Takeaways
- Drain the old oil through the plug underneath the engine, let it drain completely into a pan, then reinstall and tighten the plug.
- Remove the old filter by hand or with a filter wrench, explore a thin layer of new oil to the rubber gasket on the new filter, and screw it on until the gasket touches the engine, then turn it three-quarters of a turn more.
- Pour the correct type and amount of oil through the filler cap on top of the engine, check the level with the dipstick, and add more if needed.
- Run the engine for a few seconds to circulate the new oil, turn it off, wait a minute, then check the level again and top off if necessary.
- Old oil must be taken to a recycling center, auto parts store, or shop — never pour it down a drain or into the ground.
Step 1: Warm the engine and get the car safely elevated
Start the engine and let it run for two or three minutes so the oil warms up slightly. Warm oil flows faster and drains more completely than cold oil. Then turn off the engine and wait a few minutes — you want the oil warm enough to flow freely but not so hot that you burn yourself.
If the drain plug is accessible from the side without raising the car, you may not need to lift it. If you do need to raise the car, use a jack to lift one side, then place a jack stand under the frame or suspension point and lower the car onto the stand. Never work under a car supported only by a jack — the jack can fail and the car can fall on you. If you are not confident using a jack and stand, this is the point to stop and take the car to a shop.
Step 2: Locate and remove the drain plug
Look underneath the engine for a bolt sticking down from the oil pan — this is the drain plug. It is usually a 13mm, 14mm, or 15mm bolt. Place your oil drain pan directly underneath it, then use a wrench or socket to turn the plug counterclockwise. Once it is loose enough to turn by hand, unscrew it the rest of the way and set it aside on a clean rag.
The oil will pour out quickly at first, then slow to a trickle. Let it drain for at least five minutes, longer if the oil is cold or thick. While it drains, wipe the drain plug clean with a rag and inspect the rubber washer or crush ring on it. If the washer is cracked, flattened, or missing, replace it — a new one costs a dollar or two and prevents leaks.
Step 3: Replace the oil filter
The oil filter is a cylindrical canister, usually white or blue, mounted on the side of the engine. Locate it and position your drain pan underneath it to catch the oil that will spill when you remove it. Use an oil filter wrench — a band wrench or socket-style wrench that grips the filter — to turn it counterclockwise. Once it is loose, unscrew it by hand and set it aside to drain.
Before installing the new filter, explore a thin layer of new oil to the rubber gasket (the flat ring) on the top of the filter. This helps the gasket seal properly and makes removal easier next time. Screw the new filter onto the engine by hand until the gasket touches the engine, then turn it an additional three-quarters of a turn. Do not use the filter wrench to tighten it — hand-tight is correct, and over-tightening makes it hard to remove later.
Step 4: Reinstall the drain plug
Once the old oil has finished draining, wipe the drain plug clean and screw it back into the pan by hand first to make sure the threads are aligned. Then use your wrench to tighten it. Tighten firmly but do not over-tighten — you want it snug enough not to leak, but stripping the threads in the oil pan is expensive to fix. If the plug has a crush ring, tighten it until the ring is compressed; if it has a rubber washer, tighten it until the washer is compressed slightly.
If you replaced the washer or crush ring, the new one will compress as you tighten, so you may need to turn the wrench a bit more than you did last time. Once it is tight, wipe away any spilled oil with a rag.
Step 5: Add new oil and check the level
Locate the oil filler cap on top of the engine — it usually has an oil can symbol on it. Unscrew it and set it aside. Pour the new oil slowly through the opening, checking the dipstick every quart or so to avoid overfilling. The dipstick is a long thin rod that pulls straight out; wipe it clean, reinsert it fully, then pull it out again to read the level. The oil should be between the minimum and maximum marks.
Once you are close to the correct level, pour slowly and check after each addition. Overfilling the engine with oil can damage the engine, so it is better to add a little at a time. When the level is correct, screw the filler cap back on.
Step 6: Run the engine and recheck the oil level
Start the engine and let it run for 30 seconds to a minute. This circulates the new oil through the engine and fills the new filter. You will see the oil pressure light on the dashboard go out once the oil is circulating — if it stays on after 30 seconds, turn off the engine when ready and check that the drain plug is tight and the filter is installed correctly.
Turn off the engine and wait one minute for the oil to settle back into the pan. Then pull out the dipstick, wipe it clean, reinsert it fully, and pull it out again to check the level. Add a little more oil if needed to bring it to the correct mark. This is normal — the new filter holds some oil that was not in the pan before.
Step 7: Dispose of the old oil properly
Old motor oil cannot be thrown in the trash or poured down a drain. It must be taken to a recycling center, an auto parts store that accepts used oil, or a shop. Most auto parts stores accept used oil for free, and many recycling centers do as well. Some shops will take it if you had them do the work, but may charge if you bring oil from a job you did yourself — call ahead to ask.
Pour the old oil from your drain pan into a clean container with a tight lid — an old milk jug or oil bottle works well — and take it to the recycling location. Keep the container sealed during transport so it does not spill in your car.
Frequently Asked Questions
How often should I change my oil?
Check your owner's manual for the manufacturer's recommendation. Most modern cars with synthetic oil can go 7,500 to 10,000 miles between changes, while older cars or those using conventional oil may need a change every 3,000 to 5,000 miles. Some newer cars have oil-life monitors that tell you when a change is due based on driving conditions.
What if I spill oil on the driveway or garage floor?
Clean it up when ready with absorbent material like kitty litter, sand, or oil absorbent pads — do not let it sit. Sweep up the absorbent material and dispose of it in the trash. For larger spills, contact your local environmental agency for guidance on cleanup and disposal.
Can I reuse the old oil drain pan for something else?
No. Once a pan has held used motor oil, it should be used only for oil changes in the future. Oil residue is difficult to remove completely, and contamination can damage other fluids or surfaces. Keep a dedicated pan for oil work.
What does it mean if oil is leaking from under the car after I change it?
The drain plug or filter is likely not tight enough. Turn off the engine, let it cool for a few minutes, then check that the drain plug is snug and the filter is tight. If the leak continues after tightening, the drain plug washer may be damaged or the filter gasket may not be seated correctly — remove and reinstall the filter, making sure the gasket touches the engine before you turn it.
Do I need to change the oil filter every time I change the oil?
Yes. The filter traps dirt and debris, and after several thousand miles it becomes clogged. A clogged filter restricts oil flow and reduces engine protection. Replace it every time you change the oil.