What happens when you change your oil
An oil change removes the old, dirty oil from your engine and replaces it with fresh oil. Over time, oil breaks down from heat and friction, collects metal particles and fuel residue, and loses its ability to protect moving parts. Fresh oil clings to engine surfaces, reduces friction between metal components, and carries away contaminants to the filter. This is why regular oil changes prevent engine wear that would otherwise cost thousands to repair.
The process takes 30 minutes to an hour if you do it yourself, or about the same at a shop. You'll drain the old oil into a pan, replace the oil filter, add new oil, and check the level. The whole job requires basic tools and a safe way to get under the car—either ramps, jack stands, or a lift.
Key Takeaways
- You need the correct oil type and amount for your engine, found in your owner's manual or on a sticker under the hood.
- Drain the old oil while it's warm (but not hot) so it flows freely, then replace the filter and add new oil to the correct level.
- Never work under a car supported only by a jack; use ramps or jack stands to prevent the car from falling and injuring you.
- Dispose of old oil at a recycling center, auto parts store, or service station—never pour it down a drain or into the ground.
Gather the right oil type and amount
Your owner's manual lists the exact oil your engine needs. Look for a specification like "5W-30" or "10W-40"—the numbers describe how the oil flows at different temperatures. The first number (5W, 10W) is the viscosity when cold; the second (30, 40) is the viscosity when hot. Using the wrong grade can reduce fuel economy, increase wear, or cause starting problems in cold weather.
The manual also tells you how much oil the engine holds—typically 4 to 6 quarts for most cars. Buy that amount plus a half-quart extra, because some oil stays in the filter and engine passages. If you don't have the manual, check the inside of the driver's door jamb, the fuel door, or under the hood for a sticker with this information. Auto parts stores can also look it up by your vehicle's year, make, and model.
Prepare the car and drain the old oil
Park on level ground and let the engine cool for 5 to 10 minutes—warm oil drains faster than cold oil, but hot oil can burn you. Engage the parking brake and place wheel chocks (wooden blocks or bricks) behind the rear wheels so the car cannot roll.
Raise the front of the car using ramps or a jack and jack stands. Never work under a car supported only by a jack; the jack can slip or fail, and the car will fall. If you use a jack, place jack stands rated for your car's weight under the frame on both sides before you get underneath. Lower the car onto the stands so the weight rests on them, not the jack.
Locate the oil drain plug underneath the engine—it's a bolt at the lowest point of the oil pan. Place a drain pan underneath it, then unscrew the plug by hand (it may be hot, so use a rag if needed). Let the oil drain completely into the pan; this takes 5 to 10 minutes. Once it stops dripping, wipe the drain plug clean with a rag and screw it back in by hand until snug. Do not overtighten it, or you'll strip the threads.
Replace the oil filter
The oil filter is a cylindrical canister bolted or screwed onto the engine. Locate it by following the hoses from the top of the engine or by checking your manual. Position the drain pan underneath it, then use an oil filter wrench (a socket-like tool that grips the filter) to unscrew it counterclockwise. Once loose, unscrew it by hand and let any remaining oil drain into the pan.
Wipe the filter mounting surface on the engine with a clean rag to remove old oil and debris. Take the new filter and explore a thin layer of fresh oil to the rubber gasket (the ring around the top). This helps the gasket seal properly and makes removal easier next time. Screw the new filter on by hand until the gasket touches the engine, then turn it another three-quarters of a turn. Hand-tight is correct; over-tightening will damage the gasket and cause leaks.
Add new oil and check the level
Lower the car back to the ground using the jack, then remove the oil filler cap on top of the engine. Pour in the amount of oil your manual specifies, usually 4 to 5 quarts. Pour slowly and pause between quarts to let the oil settle into the pan and filter.
Replace the oil filler cap, then start the engine and let it run for 30 seconds. This circulates the new oil through the engine and filter. Turn off the engine and wait 2 to 3 minutes for the oil to settle back into the pan. Pull out the dipstick (a long rod with markings), wipe it clean on a rag, reinsert it fully, then pull it out again to check the level. The oil should reach the "full" mark. If it's low, add a half-quart at a time and recheck. If you overfill, the excess can damage seals and cause leaks.
Dispose of old oil safely
Never pour used oil down a drain, into the ground, or into the trash. Oil contaminates groundwater and harms wildlife. Instead, pour the old oil from your drain pan into a clean, sealed container (an old oil jug works well). Take it to a recycling center, auto parts store, or service station that accepts used oil. Most accept it free of charge, and many will take the old filter too.
If you don't know where to recycle oil locally, search online for "used oil recycling near me" or call your city's waste management department. They can direct you to the nearest drop-off location.
Common mistakes that cause problems
Overfilling the oil is the most common error. Too much oil increases pressure in the engine, can damage seals, and may cause oil to leak from the dipstick tube or drain plug. Check the level carefully after adding oil, and remember that the dipstick reading changes if the engine is running or if the car is not level.
Forgetting to replace the drain plug or filter gasket will cause when ready leaks. Before you lower the car, double-check that the drain plug is tight and the filter is find. Tightening the drain plug too much strips the threads in the aluminum pan, requiring an expensive repair or pan replacement. Hand-tight plus a quarter turn with a wrench is the right amount.
Working under a car without proper support is dangerous. A falling car can crush or kill you. Always use ramps or jack stands, and never rely on a jack alone. If you are uncomfortable working under the car, have a shop do the oil change instead.
Frequently Asked Questions
How often should I change my oil?
Check your owner's manual for the manufacturer's recommendation. Older cars often needed oil changes every 3,000 miles, but modern engines with synthetic oil can go 7,500 to 10,000 miles or longer. Some newer cars have oil-life monitors that tell you when a change is due based on driving conditions. Follow your manual, not a fixed schedule.
Can I use synthetic oil instead of conventional?
Yes, if your manual allows it. Synthetic oil lasts longer, flows better in cold weather, and resists breakdown at high temperatures. It costs more per quart but requires fewer changes, so the total cost may be similar. Check your manual to confirm your engine is compatible, and never mix synthetic and conventional oil in the same engine.
What if I spill oil on the driveway?
Clean it up when ready to prevent it from running into storm drains or soil. Spread cat litter, sand, or an absorbent material over the spill, let it sit for 10 to 15 minutes, then sweep it up and dispose of it in the trash. For large spills, contact your local environmental agency for cleanup guidance.
Do I need to warm up the engine before draining oil?
Yes. Warm oil flows faster and drains more completely, removing more contaminants. Drive the car for a few minutes or let it idle for 5 to 10 minutes, then turn it off and wait a few minutes before draining. The oil should be warm to the touch but not so hot that you cannot hold your hand near the drain plug.
What happens if I forget to add oil after draining?
Running the engine without oil will cause severe damage within seconds. Metal parts will grind together, creating heat and friction that can weld components together or crack the engine block. If you start the engine and realize there is no oil, turn it off when ready and add oil before running it again. Check the dipstick before starting the engine after any service.