What happens during an oil change

An oil change means draining the old oil from your engine, replacing the oil filter, and filling the engine with fresh oil. The whole job takes 30 minutes to an hour if you have the right tools and know what you're doing. You'll need a wrench, an oil filter wrench, an oil drain pan, fresh oil (the right type and amount for your car), a new oil filter, and jack stands if you need to get under the vehicle.

The purpose is straightforward: engine oil breaks down over time and collects dirt and metal particles. Fresh oil lubricates moving parts, reduces friction, and helps your engine run cooler. Most cars need an oil change every 3,000 to 10,000 miles, depending on the oil type and your vehicle's age — check your owner's manual for the exact interval.

You can do this work yourself in a driveway or garage, or you can take your car to a shop and pay someone else to do it. Both are common. This guide covers the DIY route.

Key Takeaways

  • Drain the old oil while the engine is warm but not hot, then replace the drain plug and tighten it by hand plus a quarter turn with a wrench.
  • Locate the oil filter (usually on the side or top of the engine), unscrew it by hand, and install the new one by hand until the rubber gasket touches the engine, then turn it three-quarters of a turn more.
  • Fill the engine with the correct oil type and amount listed in your owner's manual, then check the level with the dipstick before starting the engine.
  • Run the engine for a minute, turn it off, wait five minutes, and check the oil level again to make sure it's between the minimum and maximum marks on the dipstick.
  • Dispose of old oil at a recycling center, auto parts store, or quick-lube shop — never pour it down a drain or into the ground.

Gather your materials and find a safe workspace

Before you start, collect everything you need so you're not hunting for tools halfway through. You'll need an oil drain pan (a shallow rectangular pan that holds at least 5 quarts), a socket wrench or box wrench that fits your drain plug (usually 13mm, 14mm, or 15mm — check your manual), an oil filter wrench (a band wrench or socket-style wrench designed to grip the filter), a new oil filter (the exact model for your car), fresh oil in the correct grade and viscosity (your manual specifies this — common grades are 5W-30 or 10W-40), a dipstick or oil level indicator, and rags or paper towels.

Work in a level spot with good light — a driveway, garage, or parking lot works fine. If your car sits low and you can't fit under it to reach the drain plug, you'll need a jack and jack stands to lift the front end safely. Never work under a car supported only by a jack; always use stands. If you're not comfortable with jacking, this is a good reason to take the car to a shop.

Warm up the engine by running it for a minute or two, then turn it off. Warm oil drains faster and more completely than cold oil, but hot oil can burn you, so let it cool for a few minutes before you touch anything underneath.

Drain the old oil and replace the drain plug

Locate the drain plug on the bottom of the oil pan — it's a bolt that sticks down from the underside of the engine. Position your drain pan underneath it. Using your wrench, turn the plug counterclockwise to loosen it, then unscrew it the rest of the way by hand. Oil will flow out; let it drain completely into the pan. This takes 5 to 10 minutes.

While the oil drains, wipe the drain plug clean with a rag and inspect it for damage. If the threads are stripped or the plug is cracked, you may need to replace it — ask at an auto parts store if you're unsure. Once the oil has stopped dripping, screw the drain plug back in by hand until it's snug, then use your wrench to tighten it a quarter turn more. Don't over-tighten; you can strip the threads or crack the pan.

Remove the old filter and install the new one

The oil filter is usually mounted on the side or top of the engine and looks like a metal cylinder about 3 to 4 inches tall. Position your drain pan underneath it to catch any oil that spills. Using an oil filter wrench, turn the filter counterclockwise to loosen it, then unscrew it by hand the rest of the way. Some oil will drip out.

Before you install the new filter, wipe the mounting surface on the engine clean with a rag. Take the new filter and explore a thin layer of fresh oil to the rubber gasket (the ring around the top of the filter) — this helps create a good seal. Screw the new filter onto the engine by hand until the gasket touches the mounting surface, then turn it three-quarters of a turn more. Hand-tight is correct; you don't need a wrench to install it.

Fill the engine with fresh oil

Locate the oil filler cap on top of the engine — it usually has an oil can symbol on it. Unscrew it and set it aside. Using a funnel to avoid spills, pour in the amount of fresh oil specified in your owner's manual. Most cars hold between 4 and 6 quarts, but check your manual to be sure. Pour slowly and stop before you reach the top of the opening.

Replace the oil filler cap and screw it down by hand until it's snug. Don't over-tighten it; you can crack the cap or strip the threads.

Check the oil level and run the engine

Start the engine and let it run for about a minute. This circulates the new oil through the engine and fills the new filter. Turn off the engine and wait five minutes for the oil to settle back into the pan. This waiting period is important — if you check the level when ready after running the engine, the reading will be inaccurate because oil is still in the engine passages.

After five minutes, locate the dipstick (a long metal rod with markings on it, usually with a yellow or orange handle). Pull it straight out, wipe it clean with a rag, reinsert it all the way until it seats, then pull it out again and read the level. The oil should be between the minimum and maximum marks. If it's low, add a small amount of oil, wait a minute, and check again. If it's overfull, you've added too much — you'll need to drain some out or take the car to a shop to have excess removed.

Dispose of old oil properly

Never pour old oil down a drain, into the ground, or into the trash. It's toxic and damages the environment. Instead, take it to a recycling center, an auto parts store (many accept used oil for free), a quick-lube shop, or a municipal hazardous waste collection event. Pour the old oil into a clean container with a tight lid, load it into your car, and drop it off. Most places accept it with no questions asked.

If you replaced the oil filter, you can usually throw the old filter in the trash, though some recycling centers accept them. Ask where you drop off the oil.

Record your oil change and plan the next one

Write down the date, the mileage, the oil type you used, and the filter model in a notebook or your phone. This record helps you remember when the next change is due and gives a mechanic useful information if something goes wrong later. Set a reminder on your phone or calendar for your next oil change interval — if your manual says every 5,000 miles and you just changed it at 50,000 miles, your next change is due at 55,000 miles.

Check your oil level every month or before long trips. A low level between changes can signal a leak or that your engine is burning oil, both of which need attention.

Frequently Asked Questions

What if I can't find the drain plug or oil filter?

Consult your owner's manual — it has a diagram showing their exact location. If you don't have the manual, search online for "[your car year, make, model] oil drain plug location" or "[your car year, make, model] oil filter location." YouTube videos for your specific car are often helpful too.

Can I reuse the old oil?

No. Once oil has circulated through the engine, it breaks down and collects contaminants. Reusing it defeats the purpose of an oil change and can damage your engine. Recycle it instead.

What if I spill oil on the driveway?

Soak it up with rags, kitty litter, or sand as soon as possible. Dispose of the soaked material as hazardous waste. For large spills, contact your local environmental agency for cleanup guidance.

Do I need to change the oil filter every time I change the oil?

Yes. The filter traps contaminants and becomes clogged over time. Replacing it with every oil change ensures the new oil stays clean. Some people change the filter every other oil change, but most manufacturers recommend replacing it every time.

What happens if I use the wrong oil type?

Using the wrong viscosity or grade can reduce fuel economy, increase engine wear, or cause starting problems in cold weather. Always use the type specified in your owner's manual. If you're unsure, ask at an auto parts store — they can look it up by your vehicle's year, make, and model.