What a Harley Oil Change Kit Contains

A Harley-Davidson oil change kit bundles the items you need to drain old oil and refill your engine in one purchase. The exact contents depend on your model year and engine type, but the standard kit includes a new oil filter, the correct weight and volume of Harley-branded or approved synthetic oil, a crush washer or O-ring for the drain plug, and sometimes a filter wrench or drain plug socket.

Harley sells these kits through their dealerships and authorized retailers. The kits are model-specific—a kit for a 2020 Street 750 will not match a 2015 Road King, because oil capacities, filter sizes, and drain plug designs differ. Before you order, you need your exact year, model, and engine displacement to get the right one.

The advantage of buying a kit rather than sourcing parts separately is that everything is already matched to your bike. You do not have to guess whether the filter will thread on correctly or whether you have the right crush washer. The disadvantage is cost: kits typically run 20 to 40 percent higher than buying the same parts individually, and you pay for the convenience of having them bundled.

Key Takeaways

  • Harley oil change kits are model-specific and include the filter, oil, and drain plug hardware matched to your exact year and engine type.
  • You must know your bike's year, model, and engine size before ordering, because using the wrong kit can damage your engine or cause leaks.
  • Kits cost more than buying parts separately, but they eliminate the risk of mixing incompatible components.
  • Harley specifies oil weight and type for each model; using a different grade can affect engine wear, fuel economy, and warranty coverage.
  • The crush washer or O-ring in the kit is a one-time-use item and must be replaced at every oil change to prevent leaks.

Oil Weight and Specifications for Your Model

Harley does not use a single oil weight across all models. Older air-cooled engines typically run 20W-50 or 25W-60, while newer liquid-cooled models and smaller displacement bikes often use 10W-40 or 15W-40. The kit you buy will have the correct weight printed on the bottle and listed in your owner's manual.

The reason weight matters is that it affects how the oil flows at cold startup and how well it protects at operating temperature. Too thin an oil and your engine wears faster; too thick and you lose fuel economy and put extra strain on the starter motor in winter. Harley's specification exists because the engineers tested it in your specific engine design.

Most Harley kits now include synthetic or synthetic-blend oil rather than mineral oil. Synthetic lasts longer between changes—typically 10,000 miles instead of 5,000—and handles temperature swings better. If your bike is older and the manual says mineral oil is acceptable, you can still use synthetic, but switching back to mineral afterward is not recommended because synthetic cleans the engine more aggressively and can expose sludge buildup.

Filter Type and Fitment

The filter in your kit is designed to thread onto your specific oil filter mount. Harley has used different filter sizes and thread patterns across model generations. A filter that does not seat properly will either leak or come loose during riding, both of which will drain your oil and seize your engine within minutes.

The kit filter comes with a rubber gasket pre-installed. When you install it, you hand-tighten it until the gasket touches the mount, then turn it an additional three-quarter turn. Over-tightening crushes the gasket and causes leaks; under-tightening leaves it loose. The crush washer or O-ring that comes in the kit is for the drain plug, not the filter—do not confuse the two.

If you lose the filter wrench that sometimes comes in the kit, you can buy one separately, but it must match your filter size. Using a wrench that is too large or too small will strip the filter housing and force you to replace it, which is an expensive repair.

Drain Plug Hardware and Why It Cannot Be Reused

The crush washer or O-ring in your kit is a single-use item. Every time you drain the oil, the old washer gets compressed and loses its ability to seal. Reusing it is a common mistake that leads to slow leaks around the drain plug—oil seeps out over days or weeks, and you may not notice until the engine is already low.

Harley drain plugs are typically magnetic, which means they collect metal particles from normal engine wear. When you remove the plug, wipe the magnet clean with a rag. If you see a large amount of metal shavings—more than a light coating—it can signal bearing wear or other internal damage, and you should have a mechanic inspect the engine.

The kit includes a new washer because it is cheap and because forgetting to replace it is one of the most common causes of oil leaks. If you install the drain plug without a new washer, you are betting that the old one still seals, and you will almost certainly lose.

How to Use Your Kit for a Basic Oil Change

The process is straightforward: warm the engine for two minutes to thin the oil, turn it off, locate the drain plug underneath the engine, remove it with the socket or wrench, let the old oil drain into a pan for several minutes, install the new crush washer on the drain plug, thread the plug back in and tighten it firmly (not with a breaker bar), locate the oil filter, remove it with the filter wrench, clean the mounting surface with a rag, hand-install the new filter until the gasket touches, then turn it three-quarter turn more, and pour the new oil through the filler cap on top of the engine.

Do not overfill. Harley engines have a sight glass or a dipstick, and you fill to the mark, not to the top of the opening. Overfilled oil foams, loses its ability to cool and protect, and can blow out seals. After you fill, start the engine and let it idle for 30 seconds, then turn it off and wait two minutes for the new oil to settle before checking the level again.

Dispose of the old oil at a recycling center, auto parts store, or service station. Do not pour it down a drain or into the ground. Most places that sell oil will take used oil for free.

When to Buy a Kit Versus Individual Parts

Buy a kit if you want the certainty that all components match your bike and you do not mind paying a premium for that convenience. Buy individual parts if you already have a filter wrench, want to choose your oil brand, or have found a cheaper source for one or more items.

If you change your oil regularly and keep records, you may find that buying a kit once and then sourcing parts separately afterward makes sense. The first kit teaches you what size filter and oil weight your bike needs; after that, you can shop around.

Some riders buy kits from Harley dealerships because they trust the brand match, while others buy equivalent kits from aftermarket suppliers like Amsoil or Mobil 1 that are cheaper and work just as well. The choice depends on your comfort level with parts compatibility and your budget.

Storage and Shelf Life

Oil in a sealed container lasts several years if stored in a cool, dry place away from direct sunlight. Do not store oil in an unheated garage in winter or a hot shed in summer, because temperature swings can degrade it. A basement or climate-controlled closet is ideal.

The filter can be stored indefinitely as long as it stays dry. Do not store it where it might get crushed or where moisture can enter the open end. If you buy a kit and do not use it for more than a year, check the oil bottle for a date code or expiration marking before opening it.

Frequently Asked Questions

Can I use a different brand of oil if I have a Harley kit with the filter and washer?

Yes, as long as it meets Harley's weight and type specification for your model. The kit's value is mainly in the filter and washer, which are model-specific. The oil brand matters less than the weight—10W-40, 20W-50, and so on. Check your owner's manual for the exact spec before substituting.

What happens if I use the wrong oil weight?

Thin oil (lower numbers) flows faster but offers less protection at high temperatures, leading to faster wear. Thick oil (higher numbers) protects better but makes cold starts harder and reduces fuel economy. Using the wrong weight can also void your warranty if Harley determines it contributed to engine damage.

Do I need a special tool to install the filter?

A filter wrench makes installation and removal easier, but you can hand-tighten a new filter on and hand-loosen an old one off if you have a good grip and patience. The wrench is worth having if you plan to change your oil regularly, because it prevents stripped filters and makes the job faster.

Can I reuse the crush washer if it still looks good?

No. Crush washers compress when tightened and lose their sealing ability permanently. Reusing one is a common cause of slow oil leaks. The washer in your kit is inexpensive and designed to be replaced every time you drain the oil.

Where do I find the right kit for my specific Harley?

Call your local Harley dealership with your year, model, and engine size, or look up your bike on Harley's website and navigate to the parts section. Aftermarket retailers like RevZilla and J&P Cycles also sell model-specific kits and can confirm fitment before you order.