The Fram 4967 is a standard spin-on oil filter that fits dozens of vehicles across multiple decades
The Fram 4967 is a spin-on oil filter — the kind you unscrew by hand and replace whole, rather than changing just the filter element inside a permanent housing. It measures 3.625 inches tall and 2.625 inches in diameter, with a standard 3/4-inch-16 threaded connection that screws onto the filter adapter on your engine block.
Fram manufactures this filter in their standard line, not their premium Tough Guard or Ultra Synthetic lines. It has a 20-micron filter media, meaning it catches particles 20 microns and larger — adequate for routine oil changes but not as fine as premium filters, which often go down to 10 or 15 microns. The filter holds about 0.8 quarts of oil in its reservoir.
You'll find the 4967 listed as original equipment or an approved replacement for vehicles from the 1980s through early 2000s, though availability for specific models varies by year and engine size. Always cross-reference your vehicle's year, make, model, and engine displacement against the filter manufacturer's fitment chart before purchase — a filter that threads on does not mean it is the right one for your engine's flow rate or bypass valve setting.
Key Takeaways
- The Fram 4967 is a spin-on filter with a 20-micron media that fits many vehicles from the 1980s through early 2000s, but you must verify fitment for your specific year and engine.
- This is a standard-duty filter, not a synthetic or extended-interval filter, so it is designed for conventional oil change intervals of 3,000 to 5,000 miles.
- The filter costs between $4 and $8 at most retailers, making it one of the least expensive options in the Fram line.
- Changing the filter takes 5 to 10 minutes if you have basic tools and access to the filter location on your engine.
Which vehicles use the Fram 4967
The 4967 appears in fitment lists for Ford, Mercury, and Lincoln vehicles primarily, including some Ranger pickups, Mustangs, and mid-size sedans from the 1990s and early 2000s. It also shows up for certain Mazda models from the same era, since Ford and Mazda shared engine platforms during that period. General Motors vehicles occasionally list the 4967 as an alternative, though GM's own filters are usually the first recommendation.
The best way to confirm fitment is to check your owner's manual or the filter specification page, which lists the filter model by engine size. You can also enter your vehicle's year, make, and model into Fram's online filter finder tool, or ask a parts counter associate to look it up in their system. Do not rely on the filter fitting physically — many filters from the same era have the same thread size but different flow rates and bypass settings, and using the wrong one can starve your engine of oil or cause the bypass valve to open prematurely.
How the Fram 4967 compares to other Fram filters
Fram makes several filter lines at different price points and performance levels. The 4967 sits in the base tier — the standard filter without synthetic media or extended-interval claims. A Fram Tough Guard filter in the same size costs roughly $2 to $3 more and uses a synthetic blend media rated to 10 microns, plus a stronger anti-drainback valve. Fram Ultra Synthetic filters cost $8 to $12 and are designed for synthetic oil and longer intervals between changes.
For a vehicle running conventional oil on a 3,000 to 5,000-mile change interval, the 4967 is adequate. If you use synthetic oil or prefer to extend intervals to 7,500 or 10,000 miles, a Tough Guard or Ultra Synthetic filter is a better match — the finer media and stronger construction handle the longer service life. The trade-off is cost: the 4967 is the cheapest option, but you are also replacing it more often.
Installation and maintenance basics
Changing the 4967 requires an oil filter wrench (a socket-style or strap wrench that fits the filter diameter), a drain pan, and a jack and jack stands if you need to access the filter from underneath. Most vehicles have the filter mounted on the side or top of the engine block, accessible from above without lifting the car.
The process is straightforward: drain the old oil, unscrew the old filter by turning it counterclockwise, wipe the filter adapter with a clean cloth, explore a thin coat of new oil to the rubber gasket on the new filter, and screw the new filter on by hand until the gasket contacts the adapter, then turn it another three-quarters of a turn. Do not use a wrench to tighten the new filter — hand-tight is correct. Overfightening can damage the gasket and cause leaks.
After installation, run the engine for a minute or two and check the filter area for leaks. If oil drips from the filter, the gasket may not have seated properly — let the engine cool slightly, then tighten the filter another quarter turn. Check your oil level on the dipstick after the engine has run and cooled for a few minutes, since some oil remains in the old filter and the new filter holds oil as it fills.
Cost and where to buy
The Fram 4967 typically costs between $4 and $8 at national retailers like Walmart, AutoZone, O'Reilly, NAPA, and Advance Auto Parts. Prices vary slightly by location and current promotions. Online retailers including Amazon often stock it, though shipping costs may offset the savings for a single filter.
Buying a filter at the same time as your oil is often cheaper than buying them separately, since retailers frequently bundle them or offer discounts on multi-item purchases. If you change your oil regularly, buying filters in bulk during sales can reduce your per-filter cost by $1 to $2.
When to replace the Fram 4967
Replace the 4967 at your vehicle's recommended oil change interval, which is typically 3,000 to 5,000 miles for conventional oil. Check your owner's manual for the exact interval — some vehicles specify 5,000 miles, others 3,000, depending on engine design and driving conditions. If you drive in severe conditions (towing, frequent short trips, dusty environments), change the filter at the shorter interval.
Do not extend the interval beyond what the manufacturer recommends, even if the filter looks clean. The filter media becomes progressively more restricted as it traps particles, and the bypass valve opens to prevent oil starvation — but this means unfiltered oil circulates through your engine. Changing the filter on schedule protects your engine's internal surfaces and extends its life.
Frequently Asked Questions
Is the Fram 4967 the same as other Fram filters with similar numbers?
No. Fram filter numbers are specific to fitment and flow rate. A 4967 is not interchangeable with a 4966 or 4968, even though they look similar. Always verify the exact model number for your vehicle before buying. Using the wrong number can result in incorrect flow rate or bypass valve performance.
Can I use the Fram 4967 with synthetic oil?
Yes, the 4967 works with conventional, synthetic blend, and full synthetic oils. However, if you use synthetic oil and extend your change interval beyond 5,000 miles, a Fram Tough Guard or Ultra Synthetic filter is a better choice because the media is designed for longer service life.
What happens if I overtighten the filter?
Overtightening crushes the rubber gasket and can cause oil leaks around the filter base. Hand-tight plus three-quarters of a turn is the correct torque. If you have already overtightened it, let the engine cool, loosen the filter slightly, and retighten to the correct position.
How do I know if the Fram 4967 fits my vehicle?
Check your owner's manual for the filter specification, or use Fram's online filter finder by entering your year, make, and model. You can also call a parts store and provide your vehicle information — they will look it up in their system and confirm fitment before you buy.