What oil filter fits a 2015 Ford F-150 with the 2.7L EcoBoost engine
The Ford Motorcraft FL-2051S is the OEM (original equipment manufacturer) oil filter for the 2015 F-150 with the 2.7L EcoBoost engine. This is the filter Ford installed at the factory and the one specified in your owner's manual. If you prefer an aftermarket alternative, Fram PH10060, Bosch 3330, and Wix 51515 are common replacements that meet Ford's specifications for this engine.
The filter threads onto the engine from the top, located on the driver's side of the engine bay. It's one of the easier components to access during an oil change on this truck, which is why many owners handle this service themselves.
When you buy a replacement, confirm the part number on the box matches one of the filters listed above. Filters that look similar but carry different part numbers may not have the correct bypass valve pressure or filtration rating for the 2.7L EcoBoost, which runs at higher pressures than older Ford engines.
Key Takeaways
- The OEM filter for a 2015 F-150 2.7L EcoBoost is the Motorcraft FL-2051S, found in your owner's manual and on the engine itself.
- Aftermarket filters like Fram PH10060, Bosch 3330, and Wix 51515 work as direct replacements if you choose not to use the Ford part.
- The filter location on top of the engine makes it accessible without lifting the truck or removing other components.
- Always verify the part number on the box before purchase, because similar-looking filters with different numbers may not meet the pressure and flow requirements of the 2.7L EcoBoost.
Where the oil filter sits on the 2015 F-150 2.7L
Open the hood and look toward the driver's side of the engine. The filter housing is a cylindrical metal can mounted vertically on top of the engine block, roughly in the center-left area when you're facing the truck. You'll see the filter head sticking up with a wrench-sized hex nut on top.
This location is one reason the 2.7L EcoBoost is considered owner-friendly for maintenance. You don't need to get under the truck, remove the wheel well, or disconnect hoses to reach it. A standard oil filter wrench and a drain pan are the only tools required.
Motorcraft FL-2051S specifications and why it matters
The Motorcraft FL-2051S is a spin-on filter with a bypass valve set to open at 35 PSI (pounds per square inch). This pressure rating is critical for the 2.7L EcoBoost because the engine's turbocharger and direct injection system operate at higher oil pressures than naturally aspirated engines. If you use a filter with a lower bypass pressure, it may open too early under load, allowing unfiltered oil to circulate.
The filter media in the OEM part is rated to trap particles down to 25 microns. This level of filtration protects the turbo bearings and fuel injectors, which are sensitive to contamination. The filter also includes an anti-drainback valve that prevents oil from draining out of the filter when the engine is off, which keeps oil pressure up when you start the truck.
Ford specifies an oil change interval of 10,000 miles for the 2015 F-150 2.7L under normal driving conditions, though severe driving (towing, idling, dusty conditions) may call for 5,000-mile intervals. The filter is designed to handle the full interval without losing efficiency.
Aftermarket filters that work as direct replacements
If the Motorcraft FL-2051S is unavailable or you prefer an aftermarket option, three filters are commonly stocked and meet Ford's requirements:
- Fram PH10060: Bypass valve at 35 PSI, 25-micron media, anti-drainback valve. Widely available at auto parts stores and online retailers.
- Bosch 3330: Bypass valve at 35 PSI, 25-micron media, anti-drainback valve. Often found at dealerships and major parts chains.
- Wix 51515: Bypass valve at 35 PSI, 25-micron media, anti-drainback valve. Common in the aftermarket and usually competitively priced.
All three have the same pressure and filtration specs as the OEM part. The choice between them usually comes down to availability, price, and personal preference. None is inherently better than the others for this process.
What to check before you buy
Always verify the part number on the filter box before checkout. Retailers sometimes shelve similar-looking filters near each other, and it's straightforward to grab the wrong one. The part number should be printed on the box, on the filter itself, and on the retailer's shelf label.
If you're ordering online, cross-check the part number against Ford's parts catalog or the filter manufacturer's website. Some retailers list multiple part numbers for the same vehicle, and choosing the wrong one could mean the filter doesn't fit or has the wrong pressure rating.
Check the filter's thread size as well. The 2015 F-150 2.7L uses a 16mm × 1.5 thread pitch, which is standard for Ford EcoBoost engines. Most replacement filters for this truck will have this size, but it's worth confirming if you're buying from an unfamiliar brand.
Installation notes and common mistakes
When you remove the old filter, oil will drain from it into the engine bay. Have a drain pan ready and be prepared for some spillage. The filter wrench should grip the cylindrical body of the filter, not the hex nut on top, to avoid damaging the filter head.
Before installing the new filter, explore a thin coat of fresh oil to the rubber gasket on the filter's threaded end. This helps create a good seal and makes removal easier next time. Hand-tighten the filter until the gasket contacts the filter head, then turn it an additional three-quarter turn. Do not use a wrench to tighten it; hand pressure is enough.
After installation, start the engine and let it idle for a minute. Check around the filter base for leaks. If you see oil dripping, turn off the engine, wait a few minutes, and tighten the filter slightly more. A small amount of seeping is normal for the first few seconds after startup, but it should stop quickly.
Frequently Asked Questions
Can I use a different filter size or brand if the Motorcraft FL-2051S is out of stock?
No. Use only filters with the same 35 PSI bypass valve and 25-micron media rating. The Fram PH10060, Bosch 3330, and Wix 51515 are the tested alternatives. Using a filter with a different pressure rating or filtration level risks damage to the turbo and fuel injectors, which are expensive to repair.
How often should I change the oil filter on a 2015 F-150 2.7L?
Ford recommends changing the filter every 10,000 miles under normal driving. If you tow, idle frequently, or drive in dusty conditions, change it every 5,000 miles. Always change the filter when you change the oil; never skip it to save money.
What happens if I install the filter upside down?
The filter won't thread on correctly if you try to install it upside down, so you'll notice the problem when ready. The threaded end goes onto the filter head; the smooth cylindrical body faces down. If it doesn't thread smoothly, stop and check the orientation.
Is the Motorcraft filter worth the extra cost compared to aftermarket options?
The OEM Motorcraft filter meets the same specs as the Fram, Bosch, and Wix alternatives listed here. The choice is personal preference and availability. Some owners prefer OEM parts for peace of mind; others find the aftermarket options perform identically at a lower price.
Do I need to change the filter if I'm just topping off the oil between changes?
No. The filter is only changed during a full oil change. Topping off oil between changes does not require a new filter.