The crankcase filter removes moisture and contaminants from your engine's crankcase ventilation system
A crankcase filter (also called a crankcase breather filter) sits on your Cummins engine and traps water, dust, and oil vapors before they escape through the ventilation system. Without it, moisture and dirt would enter your crankcase, thinning your oil and accelerating wear on internal engine parts. The filter keeps air flowing in and out of the crankcase while blocking what shouldn't be there.
Cummins engines use crankcase filters across their diesel lineup — from light-duty pickups to heavy-duty trucks. The specific filter part number and replacement interval depend on your engine model and year, but the job is the same: protect your oil and engine internals from contamination.
Key Takeaways
- A crankcase filter prevents moisture and dirt from entering your engine's crankcase through the ventilation system.
- Cummins crankcase filters typically need replacement every 15,000 to 50,000 miles, depending on your engine model and operating conditions.
- A clogged or failed crankcase filter can cause oil to back up into the air intake, leading to rough idle, reduced power, and engine damage.
- You can locate your crankcase filter by checking your owner's manual or service documentation for your specific Cummins engine.
- Replacement is a straightforward maintenance task that takes 15 to 30 minutes and costs between $30 and $150 for the filter and labor.
How the crankcase ventilation system works
Your Cummins engine produces blow-by gases — fuel and combustion byproducts that leak past the piston rings into the crankcase. If these gases and pressure build up, they can damage seals, blow out gaskets, and force oil into places it shouldn't go. The crankcase ventilation system routes these gases back into the engine to be burned, but it needs to breathe in fresh air to do that.
The crankcase filter sits in this breathing path. It allows air to enter the crankcase while blocking moisture from humid air, road salt, dust, and oil mist. Over time, the filter collects all these contaminants and becomes saturated. When it does, airflow backs up, pressure rises in the crankcase, and oil can be forced into the intake manifold or out through seals.
Signs your Cummins crankcase filter needs replacement
A clogged crankcase filter often shows up as rough idle, hesitation during acceleration, or a slight loss of power. You may also notice oil residue around the filter housing or a faint burning smell. Some engines trigger a check-engine light if crankcase pressure gets too high.
The most obvious sign is oil in the intake manifold or air intake. If you open the intake and see a thin layer of oil coating the inside, your crankcase filter has likely failed and pressure has forced oil backward. This is a sign to replace the filter when ready and check your oil level, since some has escaped the crankcase.
The safest approach is to follow your Cummins maintenance schedule. Most engines call for inspection every 15,000 miles and replacement somewhere between 15,000 and 50,000 miles, depending on how dusty or humid your operating environment is. If you tow heavy loads, drive in dust, or operate in high humidity, replace it more often.
Finding the correct filter for your engine
Cummins makes different crankcase filters for different engine families. A 5.9L Cummins uses a different filter than a 6.7L, and older engines use different filters than newer ones. The wrong filter may not seal properly or may have the wrong flow rating, leaving your engine unprotected.
Start with your owner's manual or service documentation — it will list the correct part number. You can also call a Cummins dealer with your engine serial number and model year, and they will confirm the exact filter you need. Online parts retailers and truck shops that specialize in Cummins engines can cross-reference your engine to the correct filter as well.
OEM (original equipment manufacturer) Cummins filters are the most reliable choice because they are engineered to the exact specifications of your engine. Aftermarket filters are available at lower cost, but quality varies. If you choose an aftermarket filter, buy from a reputable supplier that specializes in diesel engines.
How to replace a Cummins crankcase filter
Replacement is straightforward and requires only basic tools. First, locate the filter housing — it is usually mounted on the side of the engine or on top of the valve cover. Consult your service manual for the exact location on your model. Let the engine cool for at least 30 minutes before you start.
Unscrew the filter bowl or cartridge by hand or with a filter wrench, depending on the design. Some filters unscrew like an oil filter; others have a cartridge that slides out of a housing. Drain any oil that has collected in the bowl into a drain pan. Wipe the sealing surface clean with a lint-free cloth.
Install the new filter by hand-tightening it until the rubber gasket contacts the housing, then turn it an additional three-quarter turn. Do not over-tighten — you can damage the gasket and create a leak. If your filter is a cartridge type, insert it into the housing and hand-tighten the bowl. Start the engine and check for leaks around the filter housing. If you see drips, tighten slightly more.
Maintenance intervals and operating conditions
Your Cummins maintenance schedule specifies a crankcase filter replacement interval, but real-world conditions matter. If you operate in a dusty environment — construction sites, unpaved roads, desert driving — replace the filter more often. Humidity also accelerates saturation; coastal or tropical climates require more frequent changes than dry climates.
Towing heavy loads increases blow-by and crankcase pressure, which can clog the filter faster. If you regularly tow or operate at high engine load, inspect the filter every 10,000 miles and replace it if it shows visible dirt or oil saturation. Severe-duty operation may call for replacement every 15,000 miles instead of the standard 30,000 or 50,000.
Keep records of when you replace the filter. This helps you spot patterns — if you are replacing it every 20,000 miles in normal conditions, something may be wrong with your engine's blow-by or ventilation system, and a Cummins technician should inspect it.
Cost and where to buy
An OEM Cummins crankcase filter typically costs between $40 and $120, depending on the engine model. Aftermarket filters run $25 to $80. Labor at a shop adds another $50 to $100 if you have someone else do the work. If you do it yourself, you save the labor cost and only pay for the filter.
You can buy filters from Cummins dealers, online parts retailers, truck shops, and some general automotive suppliers. Dealers may provide OEM quality but may charge more. Online retailers often have lower prices but require you to verify the correct part number before ordering. Local truck shops can usually confirm the right filter over the phone and have it in stock.
Frequently Asked Questions
Can I drive with a clogged crankcase filter?
You can drive short distances, but not safely for long. A clogged filter causes crankcase pressure to build, which forces oil into the intake and reduces engine performance. Continuing to drive risks oil starvation in the crankcase and accelerated wear on bearings and pistons. Replace it as soon as you can.
What happens if I ignore a failed crankcase filter?
Oil will be forced into the intake manifold and combustion chambers, where it burns and creates carbon buildup. This leads to rough idle, loss of power, increased emissions, and eventually engine damage. In severe cases, oil starvation in the crankcase can cause bearing failure. Replacement is much cheaper than engine repair.
Is the crankcase filter the same as the air filter?
No. The air filter cleans intake air before it enters the engine. The crankcase filter cleans air entering the crankcase ventilation system. They serve different purposes and are located in different places. Both need regular replacement, but on different schedules.
How do I know which Cummins crankcase filter I need?
Check your owner's manual for the part number, or contact a Cummins dealer with your engine serial number and model year. You can also take a photo of your current filter and show it to a truck shop — they can match it to the correct replacement. Never guess; using the wrong filter can leave your engine unprotected.
Can I use an aftermarket crankcase filter instead of OEM?
Yes, if it is from a reputable diesel engine supplier and matches your engine specifications. Aftermarket filters cost less but vary in quality. Stick with brands that specialize in diesel engines and have good reviews from Cummins owners. If you are unsure, OEM filters are the safest choice.