The Cat oil filter that fits your 6.7 Cummins depends on your engine year and whether you want OEM or aftermarket
The 6.7 Cummins diesel engine uses a spin-on oil filter mounted on the driver's side of the block. Caterpillar makes filters that work in this engine, but the part number and exact fit vary by model year. The most common Cat filter for 6.7 Cummins trucks is the Cat 1R-0750, which replaced earlier versions and fits 2013 and later models. If you own a 2007–2012 truck with a 6.7, you may need the Cat 1R-0716 instead. The difference matters because using the wrong filter can cause poor oil flow, leaks, or damage to the engine's bypass valve.
Before you buy, check your owner's manual or the filter canister on your truck right now—the part number is printed on the side. This takes 30 seconds and saves you from buying the wrong part. Dodge, Ram, and other OEM filters also fit the 6.7, so you have options beyond Cat, but if Cat is what you want, knowing the exact year and current filter type is the only way to get it right.
Key Takeaways
- The Cat 1R-0750 fits most 6.7 Cummins engines from 2013 onward; the Cat 1R-0716 is the filter for 2007–2012 models.
- Check the part number on your current filter or in your owner's manual before ordering, because using the wrong filter can restrict oil flow and damage the engine.
- Cat filters are aftermarket parts—the OEM filter from Dodge or Ram may be cheaper and is engineered specifically for your truck.
- The 6.7 Cummins uses a spin-on filter mounted on the side of the block, not a cartridge filter, so installation is straightforward but torque specs matter.
Why the 6.7 Cummins filter size and type matter
The 6.7 Cummins diesel produces high pressure and heat, and the oil filter has to handle both without collapsing or leaking. A filter that is too small or has a weak bypass valve will allow unfiltered oil to circulate when the engine is cold or when the filter gets dirty—this is called bypass flow, and it defeats the whole purpose of filtering. A filter that is too large or has the wrong thread pitch will either not fit or cross-thread onto the block, which can crack the mounting boss and cause a catastrophic oil leak.
The 6.7 also runs at higher pressures than gasoline engines, so the filter's collapse rating—the pressure at which the filter media fails—has to be high enough to handle peak oil pressure without tearing. Cat filters are rated for diesel duty, which means they meet these pressure and temperature specs. Using a filter rated only for gasoline engines is a shortcut that can fail under load.
Cat 1R-0750 versus Cat 1R-0716: which one fits your truck
The Cat 1R-0750 became the standard filter for the 6.7 Cummins starting in 2013. It has a higher flow rate and a larger media area than the earlier 1R-0716, which means it can handle more dirt and last longer between changes. If your truck is 2013 or newer, this is the filter you want.
The Cat 1R-0716 was the original filter for the 6.7 when it debuted in 2007. It is smaller and has a lower flow capacity. If you own a 2007–2012 Dodge Ram with a 6.7, this is your filter. Using the 1R-0750 on an older truck may not fit properly or may cause fitment issues with the mounting bracket, so do not assume the newer filter is always better—it has to match your truck's year and plumbing.
To confirm which one you need, look at the filter canister on your engine right now. The part number is stamped or printed on the side. Write it down and compare it to the Cat part number. If they match, you know which Cat filter to order as a replacement.
How to check your current filter and confirm the part number
Locate the oil filter on your 6.7 Cummins. It is mounted on the driver's side of the engine block, below the valve cover. You do not need to remove it to read the part number—it is printed or stamped on the cylindrical canister in large text. Use a flashlight if you need to, and wipe away any oil or dirt with a rag so you can read it clearly.
Write down the entire part number, including any letters or dashes. Then cross-reference it with Cat's filter lineup or your owner's manual. If the number matches Cat 1R-0750 or Cat 1R-0716, you know exactly what to order. If it is a Dodge, Mopar, or other brand, you can still switch to Cat, but you need to know the year of your truck to pick the right Cat equivalent.
If you cannot read the number or the filter is too dirty, check your owner's manual. The manual lists the OEM filter part number and sometimes lists approved aftermarket alternatives. This is the most reliable way to confirm what fits.
Cat filters versus OEM and other aftermarket options
The original equipment manufacturer (OEM) filter for the 6.7 Cummins is made by Dodge or Ram and is often labeled as Mopar. It is engineered specifically for your truck's oil system and bypass valve settings. OEM filters are often cheaper than Cat filters and are may provide to fit because they are what came on the truck from the factory.
Cat filters are aftermarket parts made by Caterpillar, a heavy equipment manufacturer. They are designed to meet or exceed OEM specs, and many diesel owners prefer them because Cat has a reputation for durability in high-heat, high-pressure applications. However, Cat filters usually cost more than OEM filters, and there is no performance advantage for street driving. If you change your oil on schedule, either filter will protect your engine.
Other aftermarket brands like Fram, Motorcraft, and Fleetguard also make filters for the 6.7. The key is to buy a filter rated for diesel engines and to match the part number to your truck's year. Buying the cheapest filter is a false economy—a filter that fails or leaks can cost you thousands in engine damage.
Installation and torque specs for the 6.7 Cummins filter
Installing a spin-on filter is straightforward: drain the old oil, unscrew the old filter by hand (use a filter wrench if it is stuck), clean the mounting surface on the block with a rag, and screw the new filter on by hand until the rubber gasket touches the block. Then turn it an additional three-quarter turn—no more. Over-tightening will crush the gasket and cause a leak. Under-tightening will let oil seep past the gasket.
The 6.7 Cummins filter mounting boss is aluminum and can crack if you use a filter wrench to tighten the new filter. Hand-tighten only. If the filter is so tight that you cannot remove it by hand, use a filter wrench to loosen it, but do not use a wrench to install the new one.
After installation, start the engine and let it idle for a minute. Check under the filter for leaks. If oil is dripping, stop the engine, wait a few minutes, and tighten the filter another quarter turn by hand. Do not use a wrench. If it still leaks, the gasket may be damaged or the mounting surface may be dirty—remove the filter, clean the block surface again, and reinstall with a new filter.
Oil change intervals and filter life for diesel engines
The 6.7 Cummins diesel should have its oil and filter changed every 7,500 to 10,000 miles under normal driving, or every 15,000 miles if you use Cummins-approved synthetic oil and your truck has the extended-drain package. Check your owner's manual for the exact interval for your model year and oil type. Towing, idling, or driving in dusty conditions shortens filter life, so you may need to change the filter more often.
A diesel filter works harder than a gasoline filter because diesel fuel contains more particulates and the engine runs hotter. Skipping a filter change or running past the interval will clog the filter and force the bypass valve to open, allowing unfiltered oil to circulate. This accelerates wear on bearings and increases sludge buildup. Changing the filter on schedule is cheap insurance against expensive repairs.
Frequently Asked Questions
Can I use a Cat filter on a 6.7 Cummins if my truck originally came with a Mopar filter?
Yes. Cat filters meet or exceed OEM specs and will work in any 6.7 Cummins, as long as you match the part number to your truck's year. The 1R-0750 fits 2013 and later; the 1R-0716 fits 2007–2012. There is no performance gain, but Cat filters are durable and widely available.
What happens if I install the wrong Cat filter on my 6.7?
The wrong filter may not fit the mounting boss, cross-thread onto the block, or have a bypass valve set for a different pressure range. This can cause oil leaks, restrict oil flow, or allow unfiltered oil to circulate. Always confirm the part number before you buy and install.
How do I know if my oil filter is clogged?
A clogged filter will trigger the oil pressure warning light on your dashboard, especially when the engine is cold or idling. If the light comes on and your oil level is full, the filter is likely clogged and the bypass valve has opened. Stop driving and change the filter when ready.
Is a Cat filter worth the extra cost compared to a Mopar filter?
For street driving on a regular oil change schedule, no. Both filters protect your engine equally well if changed on time. Cat filters are preferred by some diesel owners for towing or high-heat applications, but the difference is marginal for typical use. Buy whichever is cheaper and available.
Can I switch between Cat and Mopar filters on the same truck?
Yes. Both are spin-on filters with the same mounting interface. You can use Cat one change and Mopar the next without any issues, as long as you match the part number to your truck's year. There is no benefit to staying with one brand.