What oil filter your 2018 Rav4 uses

The 2018 Toyota Rav4 uses a Toyota OEM filter 90915-YFZZ9 or an equivalent aftermarket filter that meets Toyota's specifications. This is a cartridge-style filter that sits inside a plastic housing on top of the engine, not a spin-on filter that screws onto the block. The distinction matters because the replacement process is different — you remove a cap, pull out the old filter element, and install a new one, rather than unscrewing a canister.

Both the 2.5-liter four-cylinder engine (standard in all 2018 Rav4 models) and the hybrid version use the same filter part number. If you buy a replacement, verify the part number on the box matches 90915-YFZZ9 or check that the filter is labeled as compatible with 2018 Rav4 models. Many retailers stock this filter under their house brands at lower cost than the Toyota part.

Key Takeaways

  • The 2018 Rav4 uses a cartridge-style filter (Toyota 90915-YFZZ9), not a spin-on filter, so you remove a cap rather than unscrew a canister.
  • Both the standard 2.5L engine and the hybrid engine use the same filter part number and replacement procedure.
  • Aftermarket filters that meet Toyota specifications cost less than OEM parts and work the same way if the part number or compatibility label matches.
  • The filter housing sits on top of the engine and is accessible without removing other components, making this a straightforward job for a DIYer or technician.

Where the filter is located and how to access it

Open the hood and look toward the center-rear of the engine bay. The filter housing is a black plastic cylinder about three inches tall with a cap on top. You do not need to lift the car, remove wheels, or take apart the undercarriage. The housing sits in plain view once the hood is up, and you can reach it from above without contorting yourself.

Before you start, let the engine cool for at least five minutes if it has been running. The housing and filter will be warm. Have a drain pan or old towel ready — when you remove the cap, a small amount of oil will spill out, usually less than a cup. Place the pan directly under the housing to catch it.

Steps to replace the filter yourself

First, locate and remove the oil filler cap (the large cap on the valve cover) to let air into the engine as oil drains. Then position your drain pan under the filter housing. Using a filter wrench or a strap wrench, turn the housing cap counterclockwise to loosen it. Once it is loose enough, unscrew it by hand and set it aside on a clean surface.

Pull the old filter element straight up and out of the housing. It will come free easily. Inspect the rubber gasket (seal) that sits inside the cap — if it is cracked, hardened, or missing, replace the cap assembly rather than reusing it. Most Toyota dealers sell the cap and gasket as a unit for under $15.

Wipe the inside of the housing with a clean, lint-free cloth to remove any debris or old oil residue. Take the new filter element and insert it into the housing, pushing it down until it seats fully. Screw the cap back on by hand first, then tighten it with a wrench until the gasket compresses — snug but not over-tight. Over-tightening can damage the plastic housing. Reinstall the oil filler cap on the valve cover.

Start the engine and let it idle for 30 seconds, then turn it off. Wait a minute and check the oil level on the dipstick or digital gauge. Top off if needed. The filter change is complete.

Tools and supplies you will need

A filter wrench or strap wrench makes removing the cap easier, especially if it was installed tight. A socket wrench set is not required — the cap comes off by hand once you break it loose. You will need a drain pan (any shallow container works), clean rags or paper towels, and the replacement filter itself. Some people use a small flashlight to see inside the housing, but it is not essential.

If you are replacing the oil at the same time, you will also need the correct oil type and amount for your Rav4. The 2018 Rav4 with the 2.5L engine holds 3.7 quarts of 0W-20 oil. The hybrid holds 3.5 quarts. Check your owner's manual or the oil cap itself for the exact specification.

How often to replace the filter

Toyota recommends replacing the oil filter every time you change the oil. For a 2018 Rav4, that is typically every 10,000 miles or 12 months, whichever comes first, under normal driving conditions. If you drive in severe conditions — frequent short trips, towing, or dusty environments — Toyota suggests every 5,000 miles instead. Never go longer than 12 months between changes, even if you have not reached the mileage interval.

Some owners stretch intervals to 15,000 miles using synthetic oil and modern filters, but Toyota's published schedule is 10,000 miles. Sticking to the manufacturer's interval keeps your warranty intact and maintains engine protection.

OEM versus aftermarket filters

The Toyota OEM filter (90915-YFZZ9) is made to exact specifications and carries Toyota's warranty. Aftermarket filters from brands like Fram, Bosch, Mobil 1, and Wix that are labeled as compatible with 2018 Rav4 models perform the same filtration job and cost $8 to $15 less. The difference is usually in the gasket material and the thickness of the filter media, but both types meet the engine's needs.

Buy whichever filter you find at a local auto parts store or online, as long as the part number or compatibility label confirms it fits a 2018 Rav4. Avoid no-name filters from unknown suppliers. If you are unsure, ask the parts counter staff to confirm the filter matches your vehicle before you leave the store.

Common mistakes to avoid

The most common error is over-tightening the cap. The plastic housing can crack if you use a wrench to tighten too hard. Hand-tighten the cap after the gasket makes contact, then use a wrench for a final quarter-turn. That is enough.

Another mistake is forgetting to replace the gasket inside the cap if it looks worn. A bad gasket will leak oil and defeat the purpose of the filter change. If the gasket is stuck to the old filter element, peel it off and discard it — do not reuse it on the new filter.

Finally, do not skip the step of wiping the inside of the housing. Debris left behind can contaminate the new filter and reduce its lifespan. A quick wipe with a clean cloth takes 30 seconds and is worth doing.

Frequently Asked Questions

Can I use a different filter if I cannot find the 90915-YFZZ9?

Yes, as long as the replacement filter is labeled as compatible with 2018 Rav4 models and fits the cartridge-style housing. The part number does not have to match exactly — many aftermarket filters use different numbers but meet the same specifications. Check the box or ask the parts counter to confirm compatibility before you buy.

How much oil spills out when I remove the filter cap?

Usually less than a cup, but it depends on how long the engine has been off. If you change the filter when ready after driving, more oil will drain out. Always have a pan ready to catch it. The spill is manageable and does not require draining the entire oil pan.

Do I need to replace the filter cap itself or just the filter element?

Just the element in most cases. The cap and gasket are reusable if the gasket is in good condition — not cracked, hardened, or missing. If the gasket looks worn or damaged, replace the cap assembly. A new cap with gasket costs $10 to $20 and lasts for many filter changes.

What should I do with the old filter?

Take it to an auto parts store or recycling center that accepts used filters. Many stores that sell filters will take the old one for free. Do not throw it in the trash — filters contain oil and are recyclable. If you changed the oil too, the old oil and filter should go to the same recycling location.

Is the filter change the same for the hybrid Rav4?

Yes, the hybrid uses the same filter housing, part number, and replacement procedure as the standard Rav4. The only difference is the oil capacity — the hybrid holds 3.5 quarts instead of 3.7 quarts. The filter itself is identical.