The 2018 Corolla uses a cartridge-style oil filter mounted on top of the engine

Your 2018 Toyota Corolla has an oil filter that sits in a plastic housing on the top of the engine, not underneath like older cars. This cartridge-style filter is easier to access than a spin-on filter, which means you can change it without crawling under the car or dealing with oil spilling everywhere. The housing is a white or translucent plastic cap with a wrench-sized top, and it's located toward the front-left side of the engine bay when you're looking at the car from the front.

The filter itself is a cylindrical paper element that sits inside this housing. When you open the cap, you'll see the filter cartridge standing upright. This design is common on newer Toyotas because it's compact and keeps the engine bay cleaner during a change.

Key Takeaways

  • The 2018 Corolla's oil filter is a cartridge type housed in a plastic cap on top of the engine, not a spin-on filter underneath.
  • You will need a 74 mm oil filter wrench (or a strap wrench) to remove the housing cap, plus a new filter cartridge and a replacement O-ring seal.
  • The entire filter change takes about 10 to 15 minutes and requires no special tools beyond the filter wrench and a drain pan to catch spilled oil.
  • Toyota part number 04152-YZZA6 is the OEM filter cartridge for the 2018 Corolla, though aftermarket equivalents from Fram, Mobil 1, and Bosch are widely available and less expensive.

What you need to buy and where to find it

The OEM Toyota filter cartridge is part number 04152-YZZA6. You can order this directly from a Toyota dealership parts department, or search for it by that number at auto parts retailers like AutoZone, O'Reilly, NAPA, or Advance Auto Parts. The OEM cartridge typically costs between $8 and $12.

Aftermarket equivalents work just as well and cost less. Fram CH10670, Mobil 1 M1-110, and Bosch 3323 are all direct replacements. You will also need a replacement O-ring seal that comes with most cartridge filters, but if you buy the filter alone, order a seal separately—Toyota part number 90301-10001 fits the 2018 Corolla. A 74 mm oil filter wrench (also called a cartridge filter wrench) is the right tool for the job; a strap wrench works too if you already own one.

Step-by-step filter replacement

Start with the engine cold or only slightly warm—hot oil can burn you. Open the hood and locate the white plastic filter housing cap on top of the engine. Place a drain pan underneath it to catch any oil that spills when you open the cap.

Use the 74 mm filter wrench to turn the cap counterclockwise. It will loosen after a quarter turn or so; finish unscrewing it by hand. The old filter cartridge will come out with the cap. Pour any remaining oil from the housing into your drain pan. Wipe the inside of the housing clean with a lint-free cloth or paper towel.

Take the new O-ring seal and coat it lightly with fresh engine oil—this helps it seat properly and prevents leaks. Install the new filter cartridge into the housing, then screw the cap back on hand-tight. Once the O-ring contacts the housing, turn the cap an additional three-quarters of a turn with the wrench. Do not over-tighten; the seal will fail if you crush it.

Start the engine and let it run for 30 seconds, then turn it off. Wait a minute and check the oil level on the dipstick. Top up if needed. Check under the car for leaks before you drive.

Why the filter location matters for your maintenance routine

Because the cartridge filter is on top of the engine, you can change it without lifting the car or getting under it. This makes the job faster and safer, especially if you do not have a lift or jack stands. The downside is that you need the correct wrench size—a 74 mm wrench is not a standard size in most toolboxes, so you may need to buy or borrow one.

The cartridge design also means the filter housing itself can develop leaks if the O-ring wears out or if the cap is over-tightened. If you notice oil seeping from the cap after a change, the O-ring is the culprit. Replacing it costs a few dollars and takes five minutes.

Common mistakes that cause leaks or damage

The most common error is over-tightening the cap. The O-ring seal does its job when hand-tight plus three-quarters of a turn with the wrench. Cranking it harder will crush the seal and cause it to leak oil. If you over-tighten and the seal fails, you will see oil dripping from the cap within a few days of driving.

Another mistake is forgetting to oil the new O-ring before installation. A dry seal can stick to the housing and tear when you remove the cap next time, or it can fail to seal properly right away. A light coat of fresh engine oil takes two seconds and prevents both problems.

Some owners also forget to check the oil level after the change. The cartridge filter holds a small amount of oil, so the level will drop slightly when you replace it. Topping up ensures you are not running low between oil changes.

How often the 2018 Corolla filter needs replacement

Toyota recommends changing the oil and filter every 10,000 miles or 12 months, whichever comes first. If you drive in severe conditions—frequent short trips, towing, dusty roads, or extreme heat—change it every 5,000 miles instead. The filter itself does not wear out between changes; you replace it because the paper element becomes clogged with dirt and metal particles that accumulate in the oil.

If you skip filter changes, the clogged element forces oil to bypass the filter through a relief valve, meaning unfiltered oil circulates through your engine. This accelerates wear on bearings, pistons, and valve components. A $10 filter every 10,000 miles is far cheaper than engine damage from running dirty oil.

Frequently Asked Questions

Can I change the filter without changing the oil?

Yes, but it is not recommended. The filter collects particles from the oil, so old oil that has been circulating for months will still be dirty even with a fresh filter. Changing both together ensures the new filter starts with clean oil and lasts the full service interval.

What should I do with the old filter?

The old cartridge and O-ring can go in the trash. If the housing cap is cracked or damaged, replace it—Toyota part number 15610-21050 is the cap assembly. Do not reuse a damaged cap because it will leak.

Is the Toyota OEM filter worth the extra cost over aftermarket?

Both work well. OEM filters are made to Toyota's exact specifications, while aftermarket filters from Fram, Mobil 1, and Bosch meet or exceed those specs at lower cost. Choose based on your budget; neither choice will harm the engine.

Why is my new filter leaking oil?

The O-ring was either over-tightened, installed dry, or damaged during installation. Remove the cap, inspect the O-ring for tears, and replace it if needed. Reinstall with a light coat of fresh oil and tighten to hand-tight plus three-quarters of a turn only.