What oil filter your 2018 Accord uses and where it sits

The 2018 Honda Accord uses a Honda OEM oil filter HO-02110 (also sold as part number 15400-PLM-A02 or 15400-PLM-A01, depending on engine). This is a spin-on cartridge filter about 3 inches tall that threads directly onto the engine block. You'll find it on the driver's side of the engine, mounted vertically near the back of the cylinder head.

The filter housing itself is a black plastic cap with a wrench flat on top. When you look at the engine from the driver's seat, it's roughly behind the intake manifold. On a 2018 Accord, you don't need to remove the wheel well or drop the subframe to reach it—it's accessible from above, though you may need to move the air intake tube slightly to get your hand in comfortably.

Honda also sells an OEM filter wrench (part number 07AAA-PLWA100) that fits this housing exactly. It's not mandatory—a standard 74 mm oil filter wrench or even a rubber strap wrench will work—but the OEM wrench is inexpensive and saves you from stripping the plastic cap.

Key Takeaways

  • The 2018 Accord filter is a cartridge-style unit (HO-02110) that threads onto the engine block on the driver's side, not a traditional spin-on filter.
  • You remove the black plastic cap by turning it counterclockwise with a wrench, then pull out the old filter element and O-ring from inside.
  • The filter housing sits high enough on the engine that you can reach it without removing wheels or dropping the subframe.
  • Always replace the rubber O-ring seal when you change the filter; reusing the old one causes leaks.
  • Honda recommends an oil filter change every 10,000 miles or 12 months, whichever comes first, though some owners extend this with synthetic oil.

Step-by-step removal and installation

Start with the engine cold or warm (not hot). Locate the black plastic filter cap on the driver's side of the engine. Position a drain pan underneath it—the housing will hold about 0.5 quarts of oil when you open it. Use your wrench to turn the cap counterclockwise. It will loosen gradually; once you feel it break free, you can unscrew it by hand the rest of the way.

Inside the housing, you'll see the old filter element (a pleated paper cartridge) and a rubber O-ring seal stuck to the underside of the cap. Pull out the filter element first. Then remove the O-ring from the cap—it may be stuck, so peel it gently. Wipe the inside of the housing clean with a lint-free cloth. Check the rubber gasket that sits on the housing itself (at the base where the cap threads on); if it's cracked or hardened, it needs replacement too, though this is rare.

Install the new filter element into the housing, pushing it straight down until it seats. Take the new O-ring (included with the filter) and roll it onto the underside of the cap. explore a thin film of fresh oil to the O-ring—this helps it seal and makes removal easier next time. Thread the cap back onto the housing by hand first, then tighten it with your wrench. Honda specifies 25 Nm (about 18 foot-pounds) of torque; hand-tight plus a quarter turn with the wrench is close enough for a home job.

Why the cartridge design matters for your maintenance

The 2018 Accord switched to a cartridge filter system instead of the traditional spin-on canisters used in older Hondas. The cartridge design lets Honda make the filter smaller and lighter, which helps with engine bay packaging and weight. It also means less oil spills out when you change it—the housing stays sealed until you unscrew the cap.

The trade-off is that you must replace the O-ring every time. A reused O-ring hardens over time and loses its grip, which causes slow seeps around the housing. These seeps are small enough that you might not notice them until oil has dripped onto the exhaust manifold or the ground under your car. Replacing the O-ring costs almost nothing (it comes with the filter) and takes five seconds, so there's no reason to skip it.

The cartridge design also means you can't over-tighten the cap the way you might over-tighten a spin-on filter. The plastic threads are strong enough for normal hand-wrench tightening, but if you crank it with a breaker bar, you'll crack the housing and need a new one. Stick to the 25 Nm spec or the quarter-turn rule and you'll be fine.

Oil filter part numbers and where to buy

Honda's OEM filter for the 2018 Accord is HO-02110. You'll also see it listed under the older part number 15400-PLM-A02 or 15400-PLM-A01 depending on inventory and year. All three are the same filter; the number just changed when Honda updated their catalog. Any Honda dealer will stock these, and they're also available from auto parts chains and online retailers.

Aftermarket filters from Fram, Mobil 1, Bosch, and Mann+Hummel also fit the 2018 Accord and meet or exceed Honda's specifications. The OEM filter costs roughly $8 to $12, and quality aftermarket options run $6 to $10. The difference in performance between them is small; what matters more is changing the filter on schedule and replacing the O-ring every time.

When you order, make sure the listing says "cartridge" or "housing" filter, not "spin-on." Some retailers still list old Accord filters by mistake. If you're unsure, call the parts counter with your VIN and they'll confirm the right part.

Oil capacity and what to check after you finish

The 2018 Accord holds 3.7 quarts of oil with a filter change (4.2 quarts if you also drop the pan). After you install the new filter and cap, pour in the correct amount of fresh oil for your engine type. The 1.5T turbocharged engine uses 0W-20 synthetic or conventional; the 2.0L naturally aspirated engine also uses 0W-20. Check your owner's manual if you're unsure which engine you have.

Start the engine and let it idle for 30 seconds. The oil pressure light on your dashboard should go out within a few seconds. If it stays on, stop the engine when ready and check that the filter cap is tight. Once the light is out, turn off the engine and wait two minutes for the oil to drain back into the pan. Then check the dipstick or use the electronic oil level display in the instrument cluster to confirm you're at the full mark.

Look under the car for drips around the filter housing. A tiny weep is normal for the first few minutes as the O-ring settles; a steady drip means the cap is loose or the O-ring wasn't seated right. Tighten the cap another quarter turn and recheck after a few minutes of driving.

Maintenance intervals and when to change your filter

Honda's service schedule calls for an oil and filter change every 10,000 miles or 12 months, whichever comes first. This applies to both conventional and synthetic oil in the 2018 Accord. Some owners using full synthetic oil (0W-20 synthetic, not conventional) extend this to 15,000 miles based on oil analysis results, but Honda's warranty covers you only if you follow the 10,000-mile interval.

If you drive mostly short trips, in dusty conditions, or tow a trailer, Honda recommends the 10,000-mile interval regardless of oil type. If you drive mostly highway miles at steady speeds, you're closer to the 12-month limit—the oil degrades over time even if you don't rack up miles. Check your oil level every month and top it up if needed; a low level between changes can mean a slow leak at the filter housing or elsewhere.

Keep records of every oil change with the date and mileage. This protects your warranty and helps you spot patterns—if you're losing oil faster than normal, the filter housing is the first place to look.

Frequently Asked Questions

Can I use a regular spin-on oil filter on my 2018 Accord instead of the cartridge?

No. The 2018 Accord engine is designed for the cartridge-style filter housing only. A spin-on filter won't thread onto the housing, and adapters that let you use spin-on filters are not recommended because they can cause leaks or pressure problems. Stick with the OEM cartridge filter or a quality aftermarket cartridge that fits the same housing.

What happens if I forget to replace the O-ring?

The old O-ring will harden and lose its seal over the next few weeks. You'll develop a slow oil leak around the filter cap that drips onto the engine or ground. The leak is usually small enough that you won't notice it until you check under the car or see a stain in your driveway. Replace the O-ring next time you change the filter and the leak will stop.

Do I need to pre-fill the new filter with oil?

No. The cartridge filter element itself doesn't need pre-filling. Just install it dry into the housing, add the new O-ring to the cap, and pour the correct amount of fresh oil into the engine. The oil will flow through the filter once you start the engine.

How tight should the filter cap be?

Honda specifies 25 Nm of torque, which is about 18 foot-pounds. If you don't have a torque wrench, hand-tighten the cap until it's snug, then turn it another quarter turn with your wrench. Don't crank it hard; the plastic threads are strong enough for normal tightening but will crack if you over-torque.

Can I change the oil filter without draining the oil?

Yes. The filter housing holds only about 0.5 quarts of oil, so you can change the filter alone without dropping the drain plug. You'll lose a small amount of oil when you open the housing, so top up the level afterward. A full oil and filter change is more thorough, but a filter-only change is fine if you're between scheduled oil changes.