The 2017 Ford Escape uses a cartridge-style oil filter located on top of the engine

The 2017 Ford Escape oil filter is not the spin-on canister type you might be familiar with from other vehicles. Instead, Ford uses a cartridge filter — a cylindrical element that sits inside a plastic housing on the top of the engine. This design means you cannot straightforward unscrew and replace the whole unit. You remove the housing cap, pull out the old filter element, and install a new one in its place.

The filter housing is located directly above the engine block, toward the front of the engine bay. On the 2017 Escape, it is straightforward to spot once you open the hood — it is a white or translucent plastic cylinder about 3 inches tall. Knowing this location matters because it affects which tools you need and how much space you have to work.

Key Takeaways

  • The 2017 Ford Escape has a cartridge-style oil filter in a plastic housing on top of the engine, not a traditional spin-on filter.
  • You will need an oil filter cartridge wrench (usually around $10 to $20) to remove the housing cap without damaging it.
  • The correct replacement filter element is Ford part number FL-400S or equivalent aftermarket cartridges rated for the 2017 Escape.
  • The job takes 10 to 15 minutes and requires only basic tools: the filter wrench, a drain pan, and a clean rag.
  • Always replace the rubber O-ring seal on the housing cap when you install the new filter to prevent oil leaks.

What you need before you start

Gather these items before you begin: a cartridge oil filter wrench (a socket-like tool that grips the housing cap), a drain pan to catch any spilled oil, a new oil filter cartridge rated for the 2017 Escape, a new rubber O-ring seal (usually included with the filter or sold separately), and a clean rag or paper towels. You may also want a flashlight if you are working in dim light, since the housing sits in a tight spot.

The correct filter for a 2017 Ford Escape is Ford OEM part FL-400S. If you choose an aftermarket cartridge, confirm it is listed as compatible with the 2017 Escape — do not assume all cartridge filters fit. Many auto parts stores can cross-reference the part number for you if you give them the year, make, and model.

Step-by-step removal and installation

Start with the engine cold or warm but not hot. Position your drain pan under the filter housing to catch any oil that spills when you remove the cap. Use the cartridge filter wrench to grip the housing cap and turn it counterclockwise. The wrench fits over the cap like a socket, and you turn it with a ratchet or by hand if the cap is not too tight. Once the cap is loose, unscrew it the rest of the way by hand and set it aside.

Pull the old filter element straight up and out of the housing. Some oil will drip from the element and the housing, so keep the drain pan underneath. Inspect the inside of the housing for any debris or old rubber pieces. Wipe the inside clean with a rag if needed. Remove the old rubber O-ring seal from the cap — it is a small ring that sits in a groove on the underside of the cap. Discard it.

Install the new O-ring seal on the cap by pressing it into the same groove. Slide the new filter cartridge into the housing, making sure it sits flat and fully inserted. Screw the cap back onto the housing by hand first, then use the filter wrench to tighten it. Do not over-tighten — snug is enough. A wrench-tight cap is one of the most common causes of leaks on cartridge filters.

Common mistakes to avoid

The most frequent error is forgetting to replace the O-ring seal on the cap. The old seal hardens over time and will not seal properly on the second use. Even if the cap screws on, oil will weep from under it within a few days. Always install a fresh O-ring every time you change the filter.

Over-tightening the cap is the second common mistake. The plastic housing can crack if you use too much force with the wrench. Tighten until snug, then give it a quarter turn more — that is enough. If you have already over-tightened and cracked the housing, you will need to replace the entire housing assembly, which is more expensive than the filter itself.

Checking your work

After you have installed the new filter and cap, start the engine and let it run for 30 seconds. Turn it off and wait a minute, then check under the filter housing for any oil drips. If you see oil leaking from under the cap, turn off the engine, let it cool slightly, and tighten the cap a bit more. If the leak continues, the O-ring may not be seated correctly — remove the cap again and reseat the O-ring.

Check the oil level on the dipstick after the engine has run and cooled for a few minutes. The level should be at or near the full mark. If it is low, add the correct grade of oil for your 2017 Escape (check your owner's manual for the specification) until the level reaches full.

Where to buy the filter and O-ring

Ford OEM cartridge filters and O-rings are sold at Ford dealerships and most major auto parts retailers like AutoZone, O'Reilly, Advance Auto Parts, and NAPA. Aftermarket cartridge filters from brands like Fram, Motorcraft, and Bosch are also widely available. O-rings are often included with the filter, but if yours does not come with one, they cost just a few dollars and are sold separately in the oil and filter section.

Online retailers like Amazon also stock both OEM and aftermarket options, though shipping times may be longer than in-store pickup. Compare prices between retailers — cartridge filters typically cost between $8 and $18, depending on the brand.

Frequently Asked Questions

Can I use a regular spin-on filter on a 2017 Ford Escape?

No. The 2017 Escape is designed for a cartridge filter only. The housing and mounting system are not compatible with spin-on filters. Using the wrong type of filter can cause leaks or improper oil flow.

How often should I change the oil filter on a 2017 Escape?

Ford recommends changing the oil and filter together every 10,000 miles or once per year, whichever comes first. If you drive in severe conditions (towing, frequent short trips, dusty environments), change it more often — every 5,000 miles. Check your owner's manual for the specific interval that applies to your driving habits.

What happens if I over-tighten the filter cap?

Over-tightening can crack the plastic housing, which will require replacing the entire housing assembly — a much more expensive repair than the filter itself. Tighten the cap until snug, then stop. You do not need a wrench to hold it in place once it is hand-tight.

Is the old O-ring seal reusable?

No. The rubber O-ring hardens and loses its sealing ability after one use. Always install a new O-ring when you change the filter. Using an old seal is the most common cause of oil leaks after a filter change.

Do I need to drain the oil before changing the filter?

No. The cartridge filter change is separate from an oil change. You can replace just the filter without draining the oil. However, most people change the filter and oil together during regular maintenance intervals.