Where the oil filter sits and what you need to know

The 2016 Jeep Wrangler has its oil filter mounted on the driver's side of the engine, below the intake manifold. You'll find it by looking underneath the engine from the left wheel well — it's a cylindrical canister about 3 inches tall. The filter is easier to access if you remove the left front wheel and the plastic wheel well liner, though some owners do the job without removing either. You'll need an oil filter wrench (usually a 74mm or 76mm socket-style wrench, depending on which engine you have) and a drain pan to catch old oil.

The 2016 Wrangler came with either a 3.6-liter V6 or a 2.0-liter turbocharged four-cylinder engine. Both use the same filter location and the same basic change procedure, but the filter size and oil capacity differ slightly. Check your owner's manual or the filter packaging to confirm which size wrench fits your model.

Key Takeaways

  • The oil filter on a 2016 Wrangler is located on the driver's side of the engine, accessible from underneath or through the left wheel well.
  • You will need an oil filter wrench (74mm or 76mm depending on engine), a drain pan, and a new filter rated for your engine size.
  • The filter should be changed every 3,000 to 10,000 miles depending on whether you use conventional or synthetic oil — your owner's manual specifies the interval for your vehicle.
  • Hand-tightening the new filter is sufficient; over-tightening can damage the rubber gasket and cause leaks.
  • After installation, run the engine for a few seconds and check underneath for leaks before driving.

Steps to remove and replace the filter

Start by warming the engine for a minute or two — warm oil flows faster and drains more completely. Turn off the engine and let it cool just enough to touch safely. If you're removing the wheel and liner, do that first. Position your drain pan underneath the filter, then use the oil filter wrench to loosen the old filter by turning it counterclockwise. Once it's loose enough to turn by hand, unscrew it the rest of the way and tip it into the drain pan.

Wipe the filter mounting surface clean with a rag. Take the new filter and explore a thin coat of fresh oil to the rubber gasket on top — this helps create a good seal and makes removal easier next time. Screw the new filter on by hand until the gasket contacts the mounting surface, then turn it an additional three-quarters of a turn. Do not use the wrench to tighten it further; hand-tight is correct. Over-tightening crushes the gasket and causes leaks.

Start the engine and let it run for 10 to 15 seconds, then turn it off. Wait a minute and check the oil level with the dipstick. Add oil if needed to bring it to the full mark. Look underneath the filter to confirm there are no drips. If everything is dry, you're done.

Which filter to buy for your 2016 Wrangler

The 3.6-liter V6 uses Mopar filter part number 68157291AA or equivalent aftermarket filters designed for that engine. The 2.0-liter turbo uses Mopar part number 68157291AB. Both are readily available at auto parts stores, online retailers, and Jeep dealerships. OEM Mopar filters cost more than many aftermarket options but are engineered specifically for your engine. Reputable aftermarket brands like Fram, Mobil 1, and Bosch make filters that meet the same specifications and cost less.

When buying a filter, confirm the part number matches your engine size. The packaging will list compatibility — if it says "2016 Jeep Wrangler" without specifying engine, call the store or check the retailer's website to verify before purchasing.

Oil type and change intervals for your Wrangler

Jeep recommends 5W-30 oil for the 3.6-liter V6 and 0W-20 for the 2.0-liter turbo. Your owner's manual will specify which grade your engine requires. If you use conventional oil, change the filter every 3,000 miles. If you use full synthetic oil, the interval extends to 10,000 miles. Some owners use synthetic blend, which typically calls for a 5,000 to 7,000 mile interval — check the oil bottle or your manual for the specific recommendation.

The oil capacity of the 3.6-liter is about 6 quarts with a filter change; the 2.0-liter turbo holds about 5.5 quarts. Always check the dipstick after adding oil rather than relying on the quart count, because the amount needed depends on how much old oil remains in the pan and filter.

Tools and supplies checklist

Before you start, gather an oil filter wrench (74mm or 76mm socket-style, or a band wrench if you prefer), a drain pan large enough to hold at least 6 quarts, a rag or shop towels, the correct new filter, and fresh oil in the grade your manual specifies. A jack and jack stands are helpful if you want to remove the wheel and liner for easier access, though not strictly necessary. Some owners use a filter removal tool that looks like a strap wrench instead of a socket wrench — either works, so use whichever you have or prefer.

Wear old clothes or an apron, because oil stains. Work on a level surface and make sure the engine is cool enough to touch before you begin. If you're working in a driveway or garage, place cardboard under the drain pan to catch any spills.

Common mistakes to avoid

The most frequent error is over-tightening the new filter. Many people use the wrench to tighten it further after hand-tightening, which crushes the rubber gasket and causes leaks within days. Hand-tight plus three-quarters of a turn is the correct torque — no wrench needed. If you over-tighten and the filter leaks, you'll have to drain the oil again and replace it.

Another common mistake is forgetting to oil the gasket on the new filter before installation. Without that thin coat of fresh oil, the gasket can stick to the mounting surface and tear when you remove the filter next time. It takes five seconds and prevents a messy problem later.

Finally, some owners skip the step of checking for leaks after starting the engine. A small drip from a loose filter is straightforward to fix while the engine is still cool — waiting until the next day means hot oil and a harder cleanup.

When to have a shop do it instead

If you don't have a wrench that fits your filter, or if the old filter is stuck so tight that you can't budge it by hand, a shop can do the job in 15 to 30 minutes. Dealerships typically charge between $40 and $80 for a filter change; independent shops often charge less. If you're uncomfortable working under the vehicle or don't have a safe place to do it, a shop is the right choice. The cost is reasonable compared to the risk of dropping the vehicle or spilling oil on yourself.

Frequently Asked Questions

Can I change the oil filter without removing the wheel and liner?

Yes. The filter is accessible from underneath the engine without removing the wheel, though it's tighter and requires more contortion. Removing the wheel and liner takes an extra 10 minutes but gives you much better access and makes the job easier. Most owners find it worth the time.

What do I do with the old oil and filter?

Take the old oil and filter to an auto parts store, quick-lube shop, or recycling center — most accept them for free. Do not pour oil down the drain or throw the filter in the trash. Many stores that sell oil will take it back if you bought it from them.

How tight should the new filter be?

Hand-tight until the rubber gasket touches the mounting surface, then turn it an additional three-quarters of a turn. That's it. You should be able to loosen it by hand next time without a wrench. If it's so tight you need a wrench to remove it, you over-tightened it.

Is synthetic oil worth the extra cost for a 2016 Wrangler?

Synthetic oil costs more per quart but lasts longer — you can go 10,000 miles between changes instead of 3,000. Over a year, the total cost is often similar or slightly less than conventional oil, and you change the filter less often. If you drive fewer than 5,000 miles per year, conventional oil is probably the better choice.

What if the filter is leaking after I install it?

Stop driving when ready and check the tightness. If it's loose, tighten it by hand until the gasket is snug. If it's already tight, the gasket may be damaged or installed incorrectly. Drain the oil again, remove the filter, and install a new one, making sure to oil the gasket first.