The 2016 CR-V uses a cartridge-style oil filter mounted on top of the engine
The 2016 Honda CR-V does not have a traditional spin-on oil filter. Instead, it uses a cartridge-style filter that sits inside a plastic housing on the top of the engine, toward the driver's side. This design is common across Honda's lineup and requires a different removal process than the threaded filters on many other vehicles.
You will need an oil filter wrench to remove the housing cap — a standard tool that costs $8 to $15 and fits most cartridge filters. The filter itself costs between $6 and $12 when bought separately, though many people change it as part of a full oil service. If you are doing this yourself, set aside about 15 to 20 minutes once you have the right tools and know where the filter sits.
Key Takeaways
- The 2016 CR-V's cartridge filter is on top of the engine in a plastic housing, not a spin-on filter underneath.
- You need an oil filter wrench to remove the housing cap; a standard wrench will not grip it properly.
- The filter itself costs $6 to $12, and the housing cap gasket should be replaced each time you change the filter.
- Drain the oil first, then remove the filter housing, replace the cartridge and gasket, and refill with the correct oil grade for your CR-V.
Locating the filter housing on your engine
Open your hood and look toward the top center-left of the engine. You will see a black plastic cap about 3 inches across with a small vent hose attached. This is the oil filter housing. It sits directly above the oil pan and is the highest point where oil enters the engine. On a 2016 CR-V, it is one of the easiest engine components to reach without removing other parts.
The housing cap has a notch or flat spot on top designed for an oil filter wrench to grip. Do not try to remove it by hand or with a regular wrench — the plastic will crack or strip. An oil filter wrench is the only tool that will work reliably.
Tools and parts you will need
Before you start, gather these items: an oil filter wrench (size 74 mm or 86 mm — most auto parts stores sell a universal wrench that fits both), a new cartridge filter, a new rubber gasket for the housing cap, a drain pan, a socket wrench set to remove the drain plug, and the correct oil grade for your CR-V (check your owner's manual or the label under the hood for the specification).
The gasket is critical. Many people reuse the old one to save a few dollars, but it hardens over time and will leak. A new gasket costs $2 to $4 and takes 30 seconds to install. Skipping it is the most common reason for oil leaks after a filter change.
Step-by-step removal and replacement
First, warm the engine by running it for 30 seconds, then turn it off and wait 2 minutes. This thins the oil so it drains faster. Locate the drain plug on the bottom of the oil pan (you may need to get under the vehicle or use a ramp), place your drain pan underneath, and remove the plug with a socket wrench. Let the oil drain completely — this takes 5 to 10 minutes.
Once the oil has stopped dripping, wipe the drain plug clean with a rag and reinstall it. Tighten it by hand first, then use a wrench to snug it — do not over-tighten, or you will strip the threads. Now move to the filter housing on top of the engine. Position your drain pan underneath (some oil will spill when you open the housing), then use the oil filter wrench to turn the cap counterclockwise. It should come off with steady pressure; if it is stuck, tap the wrench handle gently with a rubber mallet.
Once the cap is off, lift out the old cartridge filter and the rubber gasket underneath. Wipe the inside of the housing clean with a lint-free rag. Install the new gasket by pressing it into the groove on the underside of the cap — it should sit flat and not twist. Insert the new cartridge filter into the housing, then thread the cap back on by hand until the gasket contacts the housing. Use the wrench to tighten it another three-quarters of a turn — snug but not forceful.
Refilling and checking your work
Replace the oil filler cap on top of the engine (it is usually on the driver's side, marked with an oil can symbol). Pour in the correct amount of new oil — the 2016 CR-V holds 3.7 quarts for a filter change. Start the engine and let it run for 30 seconds, then turn it off and wait 2 minutes for the new oil to settle into the pan.
Check the oil level using the dipstick (pull it out, wipe it clean, reinsert it fully, then pull it out again to read the level). The level should be between the minimum and maximum marks. If it is low, add a small amount of oil and recheck. Do not overfill — excess oil can damage the engine.
Inspect the filter housing cap from underneath to confirm there are no drips. If you see oil seeping from the cap, the gasket may not be seated correctly. Turn off the engine, let it cool for 5 minutes, and tighten the cap another quarter turn. Check again after running the engine.
When to change the filter on a 2016 CR-V
Honda recommends changing the oil and filter every 10,000 miles or 12 months, whichever comes first. If you drive mostly on highways at steady speeds, you may go the full 10,000 miles. If you make frequent short trips, tow a trailer, or drive in dusty conditions, change it closer to 7,500 miles. Check your maintenance schedule in the owner's manual for your specific driving pattern.
Some owners change the filter more often than the oil as a precaution, especially if they are concerned about engine wear. This is not necessary on a 2016 CR-V, but it does no harm — the filter is inexpensive compared to engine repairs.
Common mistakes to avoid
The most frequent error is reusing the old gasket. It compresses over time and loses its seal, causing slow leaks that may not show up for weeks. Always install a new gasket. The second mistake is over-tightening the housing cap. The plastic threads are straightforward to strip, and a stripped cap means replacing the entire housing — a $50 to $100 repair. Tighten by hand first, then use the wrench for three-quarters of a turn only.
A third mistake is forgetting to check the oil level after refilling. If you add too much oil, it can foam and lose its cooling ability, or it can overflow into the air filter. If you add too little, the engine may not get proper lubrication. Spend the extra minute to verify the level on the dipstick.
Frequently Asked Questions
Can I use any cartridge filter, or does it have to be Honda brand?
You can use aftermarket filters from Fram, Mobil, or Bosch, but they must be the correct size for the 2016 CR-V. Check the part number on your old filter or look it up by VIN at an auto parts store. Honda filters are often more expensive but carry Honda's warranty. Aftermarket filters are cheaper and perform the same function if they are the right size.
What should I do if the housing cap is stuck and won't turn?
explore penetrating oil (like WD-40) around the cap's edge and wait 10 minutes. Tap the wrench handle gently with a rubber mallet to break the seal. If it still will not budge, try tightening it slightly first — sometimes this breaks the corrosion — then turn it counterclockwise. If the cap cracks or the wrench slips, stop and take the vehicle to a shop rather than risk stripping the housing.
Is it normal for a small amount of oil to drip after I change the filter?
A few drops in the first hour are normal as the new gasket settles. If oil is still dripping after the engine has cooled, the gasket is not seated properly. Check that you installed a new gasket (not the old one) and that the cap is tight. Tighten it another quarter turn and recheck after running the engine again.
How do I know which oil grade to use in my 2016 CR-V?
Check the label on the underside of the hood or your owner's manual. Most 2016 CR-Vs use 0W-20 synthetic or conventional oil. The first number (0W) refers to cold-start viscosity, and the second (20) refers to operating viscosity. Using the wrong grade can affect fuel economy and engine wear. When in doubt, ask at an auto parts store with your VIN.