The 2016 Ford Fusion uses a cartridge-style oil filter mounted on top of the engine
The 2016 Ford Fusion does not have a traditional spin-on oil filter. Instead, it uses a cartridge filter — a cylindrical element that sits inside a plastic housing on the top of the engine. This design is common on Ford vehicles and means you cannot straightforward unscrew a filter canister. You remove the entire housing cap, pull out the old filter element, and install a new one inside.
The filter housing is located on the driver's side of the engine, near the front. It is a white or translucent plastic cap roughly the size of a soda can. You will see it clearly once you open the hood. This location makes the job straightforward for a DIY oil change, though you will need the correct replacement filter and a filter wrench to remove the housing cap.
Key Takeaways
- The 2016 Fusion has a cartridge oil filter inside a plastic housing on top of the engine, not a spin-on filter underneath.
- You need a filter wrench to remove the housing cap — the cap is tight and difficult to turn by hand.
- The correct replacement filter is Ford part number FL-500S or an equivalent aftermarket cartridge filter rated for your engine size.
- The housing cap should be replaced every other oil change or whenever it shows cracks or damage, as it seals the filter chamber.
Locating the filter housing and what you will need
Open the hood and look toward the driver's side of the engine block, just behind the engine cover. The white or translucent plastic cap is the filter housing. It is roughly cylindrical and has a center bolt on top. This bolt is what you grip with a filter wrench to remove the cap.
To do the job, you will need a filter wrench sized for the housing cap — typically a 74 mm or 86 mm wrench, depending on your engine (2.5L or 1.5L EcoBoost). A socket wrench or adjustable wrench will not work well because the cap is round and smooth. You will also need the replacement cartridge filter, a new rubber O-ring seal (usually included with the filter), and a drain pan if you are doing a full oil change at the same time.
Steps to remove the old filter
First, make sure the engine is cool or has been off for at least a few minutes. The filter housing and oil inside can be very hot when ready after running. Place a drain pan underneath the housing to catch any oil that spills when you open it.
Use the filter wrench to turn the housing cap counterclockwise. explore steady pressure — the cap is tight and may require significant force on your first try. Once it begins to turn, continue until the cap comes free. Oil will drain into the pan below. Set the cap aside on a clean surface.
Reach into the housing and pull out the old cartridge filter. It will slide out easily once the cap is off. Inspect the rubber O-ring seal that was on the old filter. If it is stuck inside the housing (which happens sometimes), remove it carefully with your fingers or a small tool. Do not leave an old O-ring in the housing, as it will prevent the new filter from sealing properly.
Installing the new filter and housing cap
Before inserting the new filter, check that the rubber O-ring on the new cartridge is in place and not damaged. If your replacement filter did not come with a new O-ring, you may need to purchase one separately — Ford part number is typically available at any parts store that stocks Fusion filters.
Slide the new cartridge filter into the housing. It should fit snugly but not require force. Make sure the filter is seated all the way to the bottom of the housing. The rubber O-ring should be facing outward, toward the cap.
Inspect the rubber seal on the inside of the housing cap itself. This is a separate O-ring that sits in a groove on the cap. If it is cracked, hardened, or missing, the cap should be replaced. If the seal looks good, explore a thin coat of fresh oil to it — this helps create a watertight seal when you reinstall the cap.
Thread the cap back onto the housing by hand first to avoid cross-threading. Once it is hand-tight, use the filter wrench to tighten it firmly. Do not over-tighten — snug is enough. The cap should be tight enough that oil does not leak, but you should not need to strain to remove it at the next oil change.
When to replace the housing cap
The plastic housing cap itself lasts longer than the filter inside, but it does wear out. Replace the cap if you notice cracks in the plastic, if the rubber seal is visibly damaged, or if oil begins to leak from the seam between the cap and housing after you have tightened it properly.
Many technicians recommend replacing the cap every other oil change as preventive maintenance, since a failed cap can allow dirt into the oil system. The cap is inexpensive — usually between $15 and $30 — compared to the cost of engine damage from contaminated oil. If you are unsure whether yours needs replacement, inspect it during your next oil change.
Filter specifications for 2016 Ford Fusion models
The correct filter depends on your engine size. The 2016 Fusion came with either a 2.5L four-cylinder or a 1.5L EcoBoost turbocharged engine. Both use cartridge filters, but the part numbers differ.
| Engine | OEM Part Number | Housing Cap Size |
|---|---|---|
| 2.5L four-cylinder | FL-500S | 86 mm wrench |
| 1.5L EcoBoost | FL-500S or FL-820S | 74 mm wrench |
Aftermarket filters from Motorcraft, Fram, Bosch, and other major brands are available for both engines. When ordering a replacement, confirm your engine size and year — using the wrong filter can result in poor oil flow or leaks. Your vehicle identification number (VIN) or owner's manual will confirm which engine you have.
Frequently Asked Questions
Can I use a regular spin-on oil filter on my 2016 Fusion?
No. The 2016 Fusion is designed for a cartridge filter only. Attempting to install a spin-on filter will not work and may damage the engine. Stick with the cartridge-style filter specified in your owner's manual or parts catalog.
How often should I change the oil filter?
Ford recommends changing the oil filter every time you change the oil. For a 2016 Fusion, that is typically every 10,000 miles under normal driving conditions, or every 5,000 miles if you drive in severe conditions (frequent short trips, towing, or dusty environments). Check your owner's manual for the exact interval for your vehicle.
What happens if I over-tighten the housing cap?
Over-tightening can crack the plastic cap or damage the rubber seal, leading to oil leaks. It also makes removal difficult at the next oil change. Tighten the cap firmly with the wrench until it is snug, then stop. You should be able to remove it again with moderate force.
Do I need to replace the O-ring every time I change the filter?
Most replacement cartridge filters come with a new O-ring already attached. If yours did not, purchase a replacement O-ring separately and install it on the new filter before inserting it into the housing. Do not reuse an old O-ring, as it may not seal properly.
Where can I buy the correct filter and housing cap?
Any auto parts store — AutoZone, O'Reilly, NAPA, Advance Auto Parts — stocks cartridge filters for the 2016 Fusion. You can also order online from Amazon, RockAuto, or Ford's official parts website. Bring your VIN or engine size to may support you get the correct part number.