The 2016 Malibu uses a cartridge-style oil filter mounted on top of the engine
Your 2016 Chevrolet Malibu has a cartridge oil filter — a cylindrical canister that screws into a housing on the top of the engine, not a spin-on filter that hangs underneath. This matters because you cannot straightforward unscrew it like a traditional filter. The housing cap itself unscrews, and the filter element slides out from inside. It is a straightforward job if you know where to look and what to expect.
The filter housing sits on the driver's side of the engine, toward the front. When you open the hood, you will see a black plastic cap with a wrench symbol molded into the top. That cap is what you turn. Knowing this upfront saves you from hunting around the engine bay or accidentally trying to remove something else.
Key Takeaways
- The 2016 Malibu's oil filter is a cartridge type housed under a black plastic cap on top of the engine, not a traditional spin-on filter underneath.
- You will need an oil filter wrench (usually 74 mm or 86 mm, depending on your engine size) to remove the housing cap without stripping it.
- The filter element itself costs between $8 and $15, and the housing cap gasket should be replaced every time you change the filter to prevent leaks.
- Draining the old oil and replacing the filter takes about 30 to 45 minutes if you have the right tools and a safe way to lift the vehicle.
- Over-tightening the housing cap is the most common mistake and can crack the plastic or damage the gasket seal.
What tools and parts you need before you start
Gather these items before you get under the car. You will need an oil filter wrench sized for your Malibu's housing cap — most 2016 models use either a 74 mm or 86 mm wrench, depending on whether you have the 1.5-liter turbo or the 1.8-liter engine. A socket wrench set often includes these sizes, or you can buy a dedicated cartridge filter wrench for $10 to $20. Do not try to remove the cap by hand or with pliers; you will strip the plastic or slip and damage the engine.
You will also need a new filter element (the part that actually filters the oil) and a new housing cap gasket — a rubber seal that sits between the cap and the housing. The gasket is small and inexpensive (usually $3 to $5), but it is the seal that keeps oil from leaking out. Many people reuse the old gasket and end up with a slow leak weeks later. Replace it every time.
Have an oil drain pan ready, fresh oil in the correct grade (check your owner's manual; most 2016 Malibus use 0W-20), a socket set, a wrench, and a jack with jack stands if you need to lift the vehicle to access the drain plug. Wear gloves and old clothes — oil stains.
Step-by-step filter replacement process
Start by warming the engine for a minute or two, then turn it off and let it cool slightly. Warm oil drains faster and more completely. Locate the oil drain plug underneath the engine (a bolt on the bottom of the oil pan) and place your drain pan underneath it. Unscrew the drain plug by hand or with a wrench, and let the old oil drain completely — this takes 5 to 10 minutes.
While the oil drains, move to the top of the engine. Locate the black plastic housing cap on the driver's side. Position your oil filter wrench over the cap and turn it counterclockwise. The cap will unscrew; keep turning until it comes free. Inside the housing, you will see the old filter element. Lift it straight out and set it aside. Wipe the inside of the housing with a clean rag to remove any debris or old gasket material.
Take the new filter element and insert it into the housing, making sure it sits flat on the bottom. Place the new gasket on the housing cap — it should sit in the groove on the underside of the cap. Screw the cap back on by hand first, then use your filter wrench to tighten it. Tighten until the gasket just touches the housing, then turn the wrench another three-quarters of a turn. Do not over-tighten; the plastic cap can crack, and the gasket can be damaged.
Once the filter is find, reinstall the oil drain plug and tighten it snugly — you do not need to crank it hard. Add the correct amount of fresh oil (check your manual; most 2016 Malibus hold about 4.5 to 5 quarts), then start the engine and let it run for 30 seconds. The oil pressure light should go out. Turn off the engine, wait a minute, and check the oil level on the dipstick. Top up if needed. Check under the car and around the filter housing for leaks.
Common mistakes that cause leaks or damage
The most frequent error is over-tightening the housing cap. The plastic threads are not as strong as metal, and turning the wrench too hard will crack the cap or compress the gasket unevenly, creating a leak that shows up a few days later. Tighten until snug, then stop. If you have already over-tightened and see a leak, the cap and gasket will need to be replaced.
Another mistake is reusing the old gasket. The rubber flattens and hardens after one oil change cycle, so it no longer seals properly. A new gasket costs almost nothing compared to the mess and engine damage a slow oil leak can cause. Always replace it.
Some owners forget to refill the housing with fresh oil before screwing the cap back on, or they add the wrong oil grade. Check your owner's manual for the exact specification. Using the wrong viscosity can affect engine wear and fuel economy, especially in cold weather.
When to replace the filter and what interval to follow
Chevrolet recommends changing the oil and filter every 7,500 miles or every 6 months, whichever comes first, for the 2016 Malibu under normal driving conditions. If you drive in severe conditions — frequent short trips, towing, dusty roads, or extreme temperatures — change it every 3,000 to 5,000 miles. Check your owner's manual for the specific severe-service schedule for your situation.
The filter does the work of trapping dirt, metal particles, and combustion byproducts that accumulate in the oil. Over time, the filter media becomes saturated and stops working effectively. Sticking to the recommended interval keeps the oil clean and protects the engine's moving parts — bearings, pistons, and valve trains — from wear. A clogged filter can also trigger the oil pressure warning light on your dashboard.
Oil filter specifications for the 2016 Malibu
The correct filter part number depends on your engine. For the 1.5-liter turbo and 1.8-liter engines, Chevrolet recommends a filter that meets GM specification 6094M. Common aftermarket equivalents include Fram PH8A, Mobil 1 M1-110, and Bosch 3330. These are all cartridge-style filters designed for the same housing. Do not buy a spin-on filter by mistake — it will not fit.
The housing cap gasket is a separate part, often sold as a kit with the filter or purchased individually. Make sure you have the gasket before you start the job. If you buy the filter and gasket separately, verify they are for the 2016 Malibu to avoid compatibility issues.
Why this maintenance matters for your engine
Oil is the lifeblood of your engine. It lubricates moving parts, carries away heat, and suspends contaminants so they do not settle on critical surfaces. The filter removes those contaminants before they can cause damage. A clean filter and fresh oil reduce friction, lower operating temperature, and extend the life of the engine. Skipping oil changes or running on a clogged filter accelerates wear on bearings and valve trains, leading to noise, loss of power, and eventually catastrophic failure.
Regular filter changes are also cheap insurance. A $15 filter and $30 in oil cost far less than an engine rebuild or replacement, which can run into thousands of dollars. The 30 to 45 minutes you spend on this job every few months is time well spent protecting one of the most expensive parts of your vehicle.
Frequently Asked Questions
Can I change the oil filter without changing the oil?
Technically yes, but it is not recommended. The filter and oil work together — as the filter clogs, the oil becomes dirtier and less effective at protecting the engine. Changing one without the other defeats the purpose. Change them together on the same schedule.
What should I do with the old oil and filter?
Take them to a recycling center, auto parts store, or quick-lube shop. Most accept used oil and filters for free or a small fee. Never pour oil down the drain or throw the filter in the trash — oil contaminates groundwater and soil, and filters take up landfill space.
How do I know if my oil filter is clogged?
The oil pressure warning light on your dashboard is the main sign. You may also notice the engine running hotter than usual or a slight loss of power. If the light comes on, stop driving and check the oil level and filter condition. A clogged filter restricts oil flow and can damage the engine if ignored.
Is the cartridge filter more expensive than a spin-on filter?
The filter element itself costs about the same, but the cartridge design requires a new gasket each time, adding a few dollars to the total cost. The trade-off is that cartridge filters are less messy to change and take up less space on the engine, which is why Chevrolet chose this design for the Malibu.
What happens if I over-tighten the housing cap?
The plastic cap can crack, or the gasket can be compressed unevenly, causing an oil leak. If you notice a leak around the cap after changing the filter, the cap and gasket will need to be replaced. Tighten until snug, then stop — you do not need to crank the wrench hard.