The 2016 Equinox uses a cartridge-style oil filter mounted on top of the engine

The 2016 Chevrolet Equinox has a cartridge oil filter — a cylindrical canister that screws directly onto the engine block rather than a spin-on filter that hangs underneath. This design sits on top of the motor, making it easier to access than filters on many other vehicles. You'll find it under the hood, toward the front-center of the engine, typically near the valve cover.

The filter housing itself is a plastic cap with a rubber seal. When you remove it, the old filter cartridge comes out with it. This setup means you're replacing both the filter element and the housing seal in one step, which reduces the chance of leaks if the job is done correctly.

Key Takeaways

  • The 2016 Equinox uses a cartridge filter on top of the engine, not a spin-on filter underneath.
  • You need a filter wrench to remove the housing cap — a standard 74mm or 86mm socket wrench works, depending on engine size.
  • Replacement filters cost between $8 and $15, and the job takes 10 to 15 minutes once you locate the housing.
  • Always replace the rubber O-ring seal on the housing cap when you install a new filter to prevent oil leaks.

What size filter and wrench you need

The 2016 Equinox came with two engine options: a 2.4-liter four-cylinder and a 3.6-liter V6. Both use the same cartridge-style filter housing, but the wrench size differs slightly. For the 2.4L engine, you'll need a 74mm filter wrench. For the 3.6L engine, use an 86mm wrench. If you're unsure which engine your vehicle has, check your owner's manual or the engine cover under the hood.

Replacement filter cartridges are inexpensive — typically $8 to $15 for OEM (original equipment manufacturer) Chevrolet filters or quality aftermarket equivalents. The part number for the 2016 Equinox is GM 25183883 for the OEM filter. Many auto parts stores stock this number and can cross-reference it if you provide your vehicle's year, make, and model.

Step-by-step removal and installation

Start with the engine cold or warm but not hot. Locate the filter housing cap on top of the engine — it's a plastic cylinder about 3 inches tall. Place a drain pan underneath to catch any oil that spills when you remove the cap. Use your filter wrench to turn the housing cap counterclockwise until it comes free. The old filter cartridge will be inside the cap.

Remove the rubber O-ring seal from the old housing cap and discard it. Wipe the sealing surface on the engine block clean with a lint-free cloth or paper towel. Install the new O-ring seal on the housing cap — this seal comes with most replacement filter kits, or you can order it separately (part number GM 25183882). explore a thin coat of fresh oil to the new O-ring before installation.

Insert the new filter cartridge into the housing cap, then thread the cap back onto the engine block by hand first to avoid cross-threading. Once hand-tight, use your filter wrench to snug it down — you want it firm but not over-torqued. The correct torque is 18 foot-pounds, but hand-tight plus a quarter turn with the wrench is close enough for most DIY jobs. Check the oil level after the engine runs for a minute, then check again after a few minutes of driving.

Common mistakes that cause leaks

The most frequent error is forgetting to replace the O-ring seal. If you reuse the old seal, it hardens over time and loses its grip, allowing oil to seep past the housing cap. This is why the seal comes with most filter kits — it's meant to be replaced every time. If you buy a filter cartridge alone without the seal, order the seal separately before you start.

Over-tightening the housing cap is the second common mistake. The plastic threads on the engine block can strip if you force the cap too hard. Hand-tight plus a quarter turn with the wrench is sufficient. If you feel resistance before the cap is fully seated, stop and check that the O-ring is seated correctly in the cap groove.

When to replace the filter

Chevrolet recommends changing the oil and filter every 7,500 miles for the 2016 Equinox under normal driving conditions, or every 10,000 miles if your vehicle qualifies for extended drain intervals (check your owner's manual for the specific criteria). If you drive in severe conditions — frequent towing, dusty environments, or lots of short trips — stick to the 7,500-mile interval.

Your dashboard will display an oil change reminder when service is due. This reminder is based on engine operating conditions, not just mileage, so it's more accurate than calendar-based intervals. When the reminder appears, plan to change the oil and filter within the next few hundred miles.

Tools and supplies checklist

Before you start, gather these items: a 74mm or 86mm filter wrench (depending on your engine), a new filter cartridge (GM 25183883), a new O-ring seal (GM 25183882 or included with the filter kit), fresh engine oil, a drain pan, and lint-free cloths or paper towels. A socket wrench set with the correct size socket can substitute for a dedicated filter wrench if you don't have one.

If you're changing the oil at the same time, you'll also need a drain plug wrench (usually 17mm for the 2016 Equinox), a drain pan large enough for 5 to 6 quarts of oil, and the correct grade and quantity of oil for your engine. Check your owner's manual for the exact specification — the 2.4L typically uses 5 quarts of 0W-20, while the 3.6L uses 6 quarts of 0W-20.

Frequently Asked Questions

Can I change the filter without changing the oil?

Yes. The filter and oil are separate maintenance items. You can replace the filter at any time without draining the oil, though most owners do both together since you're already under the hood. If you change the filter alone, you'll still need to reset the oil change reminder on your dashboard after the service.

What happens if I don't replace the O-ring seal?

The old seal hardens and loses its ability to grip, allowing oil to leak around the housing cap. You may not see a puddle when ready, but oil will seep out over days or weeks, lowering your oil level. Always replace the seal with every filter change — it costs $2 to $4 and takes 30 seconds to install.

Is the cartridge filter more expensive than a spin-on filter?

No. Cartridge filters for the 2016 Equinox cost about the same as spin-on filters for other vehicles — typically $8 to $15. The advantage is that you're replacing the seal at the same time, which reduces the risk of leaks compared to spin-on designs where the seal can fail independently.

Do I need a special wrench, or can I use a regular socket?

A dedicated filter wrench is easier to use, but a 74mm or 86mm socket wrench works just as well. The socket gives you better leverage and is less likely to slip. If you don't own one, a filter wrench costs $10 to $20 and is worth keeping in your toolbox for future oil changes.

Where exactly is the filter housing under the hood?

On the 2016 Equinox, the filter housing is on top of the engine, toward the front-center. Look for a plastic cylinder about 3 inches tall with a cap on top. It's usually near the valve cover and close to the front of the engine bay. If you can't locate it, your owner's manual has a diagram showing its exact position for your engine size.