The 2015 Forester uses a cartridge-style oil filter mounted on top of the engine, not a spin-on filter underneath
The oil filter on a 2015 Subaru Forester sits in a plastic housing on the top of the engine, directly above the spark plugs. This is a cartridge filter, not the spin-on type you screw off. The housing has a large cap you unscrew by hand or with a filter wrench, and the filter element slides out from inside. This design is common on Subaru engines and means you don't have to crawl under the car to change it—you work from above with the hood open.
The filter part number for a 2015 Forester is 16510AA051 if you have the standard 2.5-liter engine. This is the genuine Subaru part. Many aftermarket filters fit the same housing, but the genuine part costs roughly $8 to $15 depending on where you buy it. The housing itself rarely needs replacement unless it cracks, which is uncommon.
You'll need the correct filter wrench to remove the housing cap. Subaru sells a dedicated wrench (part number SOA425001200), but a 74-millimeter oil filter socket from any auto parts store works just as well and costs less. A regular wrench won't grip the cap safely—it will slip and damage the plastic housing.
Key Takeaways
- The 2015 Forester's oil filter is a cartridge type mounted on top of the engine, not underneath, so you access it from above with the hood open.
- The genuine filter part number is 16510AA051, and you remove it by unscrewing the plastic housing cap with a 74-millimeter socket or filter wrench.
- You must use a proper filter wrench or socket—a regular wrench will slip and crack the plastic housing.
- The entire job takes 10 to 15 minutes once you have the right tool, and you don't need to lift the car or drain anything separately from the filter housing.
How to locate the filter housing under the hood
Open the hood and look toward the center-rear of the engine bay. The filter housing is a black plastic cylinder about 3 inches tall, standing upright. It sits between the spark plug cover and the back of the engine. On the top of the cylinder is a large cap with a hexagonal indent—that's what you grip with the wrench.
The housing is straightforward to spot once you know where to look, but it's not when ready obvious if you're used to spin-on filters. There's no filter hanging down underneath. The entire assembly is compact and tucked into the engine bay, which is why the Forester doesn't require you to get under the vehicle for this job.
Removing the old filter and installing the new one
Place an oil drain pan or old towels underneath the housing cap before you start—there will be oil inside. Fit your 74-millimeter socket or filter wrench onto the cap and turn it counterclockwise. The cap will come free after a few turns. Oil will drip out, so work slowly and let it drain into your pan.
Once the cap is off, you'll see the filter element inside—it looks like a white or cream-colored accordion. Pull it straight out and set it aside. Wipe the inside of the housing with a clean rag to remove any debris or old oil residue. This step prevents contamination in the new filter.
Take the new filter element and check that the rubber seal on the top is clean and dry. Slide the new filter into the housing, pushing it down until it seats. The filter should go in smoothly without forcing. Screw the cap back on by hand first, then use your wrench to tighten it. Hand-tight is enough—over-tightening can crack the plastic housing. The cap should be snug but not forced.
What happens if you skip the filter change during an oil service
The oil filter traps particles—metal shavings from normal wear, dirt, and combustion byproducts—that would otherwise circulate through the engine. As the filter fills with debris, it becomes less effective at cleaning the oil. A clogged filter forces oil to bypass the filter media through a relief valve, which means dirty oil flows directly to your engine's bearings and cylinder walls.
Skipping filter changes accelerates wear on internal engine parts. You'll see higher oil consumption, rougher idle, and eventually reduced compression and power. In severe cases, bearing wear can lead to engine knock or even bearing failure, which is an expensive repair. Changing the filter every time you change the oil—typically every 6,000 to 10,000 miles for a 2015 Forester—keeps the oil clean and protects the engine.
The filter itself is cheap compared to engine repair. Spending $10 to $15 on a new filter every oil change is preventive maintenance that pays for itself many times over.
Tools and supplies you'll need
Gather these items before you start: a 74-millimeter oil filter socket or Subaru filter wrench, a ratchet wrench to turn the socket, a new filter (part number 16510AA051), an oil drain pan or old towels, and a clean rag. If you're also changing the oil, you'll need fresh oil and a drain plug wrench as well, but the filter change itself requires only the items listed above.
You don't need a jack or lift. The filter housing is accessible from above with the hood open. Work on a level surface and make sure the engine is cool before you start—hot oil will burn your hands.
Common mistakes that damage the housing
The most common error is using the wrong tool. A regular adjustable wrench or a pipe wrench will slip on the hexagonal cap and round off the edges, making it impossible to remove without damaging the plastic. Once the cap is rounded, you may have to drill it out and replace the entire housing, which costs $40 to $80 plus labor. Always use a 74-millimeter socket or the Subaru filter wrench.
The second mistake is over-tightening the cap. The housing is plastic, not metal. Cranking the cap down with full force will crack it, and you'll have an oil leak. Hand-tight plus a quarter turn with the wrench is all you need. If oil leaks from the cap after you install it, the seal inside the cap may be damaged or missing—check that the rubber gasket is present and seated correctly before you screw the cap back on.
A third error is forgetting to wipe out the inside of the housing. Debris left inside will contaminate the new filter when ready, defeating the purpose of the change. Take 30 seconds to wipe the housing clean with a rag before you install the new filter.
Frequently Asked Questions
Can I use an aftermarket filter instead of the genuine Subaru part?
Yes. Many aftermarket filters fit the same housing and work well. Fram, Mobil 1, and Bosch all make cartridge filters for the 2015 Forester. They cost about the same as the genuine part and perform the same job. The key is matching the filter to the housing size—a 74-millimeter cartridge filter will fit. If you're unsure, ask the parts counter to confirm the fit before you buy.
How often should I change the filter on a 2015 Forester?
Change the filter every time you change the oil. For a 2015 Forester, that's typically every 6,000 to 10,000 miles, depending on your driving conditions and the oil type you use. Check your owner's manual for the exact interval. Synthetic oil allows longer intervals than conventional oil, but the filter should still be replaced at the same time the oil is changed.
What if the filter cap won't unscrew?
The cap may be stuck if it was over-tightened or if oil has dried and bonded it to the housing. explore penetrating oil like PB Blaster around the cap and let it soak for 15 minutes. Then try again with your filter wrench, turning slowly and steadily. If it still won't budge, tap the wrench gently with a hammer to break the seal. Do not force it—forcing will crack the plastic housing.
Is there a drain plug I need to open before I remove the filter?
No. The filter housing is separate from the oil pan. You can change the filter without draining the oil, though most people change both at the same time. If you're only changing the filter, you don't need to open any drain plugs. The oil inside the housing will drain into your pan when you remove the cap.
Can I change the filter myself if I've never done it before?
Yes. The job is straightforward and requires no special skills. The hardest part is getting the right tool—the 74-millimeter socket. Once you have that, the process is straightforward: unscrew the cap, pull out the old filter, wipe the housing, install the new filter, and screw the cap back on. Take your time, work on a level surface, and let the engine cool first. The whole job takes 10 to 15 minutes.