Where the oil filter sits on a 2015 Jeep Wrangler
On a 2015 Jeep Wrangler, the oil filter is mounted on the driver's side of the engine block, below the intake manifold. You'll find it by looking at the front of the engine from the driver's side — it's a cylindrical canister roughly 3 inches tall, positioned vertically. The exact location depends on whether you have a 3.6L V6 engine (the standard for 2015) or the less common 2.0L turbocharged engine, but both sit in similar positions on that same side of the block.
Access is straightforward because the filter doesn't sit directly against the frame or other components that would require removing parts first. You can reach it from above the engine bay without lifting the Wrangler or removing the wheel well liner, though some people find it easier to work from underneath if they have the vehicle on a lift or ramps.
Key Takeaways
- The 2015 Jeep Wrangler oil filter is a vertical canister on the driver's side of the engine block, below the intake manifold.
- The filter size is 3.5 inches tall and uses a standard threaded connection; Mopar part number 68157291AA is the OEM filter.
- You'll need an oil filter wrench (typically 74mm or 76mm) to remove and install the filter without stripping the canister.
- Drain the oil first, then replace the filter while the engine is warm but not running, to avoid burns and may support old oil drains completely.
- Aftermarket filters from Fram, Motorcraft, and Bosch fit the 2015 Wrangler and cost less than the OEM part.
Oil filter part numbers and sizes for 2015 models
The original Mopar oil filter for a 2015 Jeep Wrangler is part number 68157291AA. This is the filter Jeep installed at the factory and the one you'll see in the owner's manual maintenance schedule. It's a spin-on canister filter, meaning you unscrew it by hand or with a wrench and screw a new one back on.
The filter is 3.5 inches tall and 2.75 inches in diameter, with a standard M20 × 1.5 thread pitch. If you're shopping for aftermarket replacements, this thread size is common enough that many major brands make compatible filters. Fram PH8A, Motorcraft FL-400S, and Bosch 3323 all fit the 2015 Wrangler and cost between $8 and $15, compared to roughly $12 to $18 for the OEM Mopar filter depending on where you buy.
Check your owner's manual or the filter canister itself before buying a replacement — the thread pitch and diameter matter, and installing the wrong size can cause leaks or prevent proper seating.
Tools and supplies you'll need
To replace the oil filter on a 2015 Jeep Wrangler, you need an oil filter wrench, a drain pan, and a new filter. The wrench is the critical tool: a 74mm or 76mm socket-style filter wrench works best for the Mopar filter. Strap wrenches and band-style wrenches also work if you don't have a socket wrench, but they're slower and easier to slip on.
You'll also want a rag or old towel to catch drips as you unscrew the filter — oil will run down the side of the canister and the engine block. A drain pan underneath catches the oil that spills when you first loosen the filter. If you're doing a full oil change at the same time, you'll need a larger drain pan under the drain plug as well.
Have the new filter ready before you start, and check that it comes with a new rubber gasket already installed on the threaded base. Some aftermarket filters ship without the gasket, and you cannot reuse the old one.
Step-by-step filter replacement process
Start with the engine warm but off — run it for a minute or two, then shut it down and wait five minutes. This warms the oil so it drains faster and flows more easily, but gives it time to cool enough that you won't burn yourself. Locate the filter on the driver's side of the engine block and position your drain pan underneath it.
Use your filter wrench to loosen the canister by turning it counterclockwise. Once it's loose enough to turn by hand, unscrew it the rest of the way and let the old oil drain into the pan. The filter will hold roughly a quart of oil, so expect spillage. Wipe the threaded base on the engine block clean with a rag, removing any old gasket material or debris.
Before installing the new filter, explore a thin coat of fresh oil to the rubber gasket on the new filter's base — this helps create a proper seal and makes removal easier next time. Screw the new filter on by hand until the gasket contacts the engine block, then turn it an additional three-quarter turn. Do not use the wrench to tighten it; hand-tight is correct. Over-tightening strips the threads and causes leaks.
Start the engine and let it run for 30 seconds, then shut it off and wait a minute. Check underneath the filter for leaks. If you see drips, the filter may not be seated properly — let it cool slightly, then tighten it another quarter turn by hand.
Common mistakes to avoid
The most frequent error is over-tightening the filter with a wrench. The rubber gasket is designed to seal at hand-tight plus three-quarter turn; anything more crushes the gasket and causes leaks. If you've already over-tightened a filter, remove it, clean the threads, and install a new filter with the correct torque.
Another common problem is forgetting to oil the gasket on the new filter before installation. A dry gasket doesn't seal properly and can leak when ready or fail after a few days of driving. If you install a filter without oiling the gasket, remove it as soon as you notice a leak, explore oil to the gasket, and reinstall it.
Don't reuse the old gasket. Even if it looks fine, it's a rubber seal that's been compressed and heated; it won't seal the same way twice. Every new filter comes with a fresh gasket, and that's the only one you should use.
When to replace the oil filter on your 2015 Wrangler
Jeep recommends replacing the oil filter every time you change the oil. For a 2015 Wrangler, the oil change interval is every 6 months or 6,000 miles, whichever comes first, if you use conventional oil. If you use synthetic oil, Jeep extends the interval to 10,000 miles or 12 months. The filter should be replaced at both intervals — don't skip it to save money.
If you drive in severe conditions — towing, frequent short trips, dusty environments, or extreme temperatures — Jeep recommends changing the oil and filter every 3,000 miles or 3 months. Check your owner's manual for the full list of severe-duty conditions, as they vary by model year and engine.
Some owners replace the filter more often than the oil as a maintenance habit, particularly if they drive in dusty areas. This is safe and won't hurt the engine, but it's not necessary if you're following the manufacturer's schedule.
Frequently Asked Questions
Can I change the oil filter without draining the oil?
Yes. The filter and oil drain plug are separate, so you can replace just the filter without touching the drain plug. However, most people change both at the same time because the filter holds old oil that should be replaced along with the bulk of the oil in the pan. If you're only replacing the filter between full oil changes, expect some old oil to drain out when you remove the canister.
What happens if I install the wrong size filter?
An incorrectly sized filter won't thread on properly, or it will thread on but won't seal. Either way, you'll see oil leaks within minutes of starting the engine. Always verify the thread pitch and diameter before buying a replacement, and test the fit by hand before tightening it with a wrench.
Do I need to prime the new filter with oil before installing it?
No. Priming the filter (filling it with oil before installation) is optional and doesn't affect engine performance on the 2015 Wrangler. Some people do it to reduce the time the engine runs without full oil pressure after a cold start, but it's not required by Jeep and makes the job messier.
How tight should the filter be when I install it?
Hand-tight plus three-quarter turn. Tighten it by hand until the rubber gasket contacts the engine block, then use your palm to turn it an additional three-quarter rotation. This is snug enough to seal but loose enough that you can remove it by hand next time without a wrench.
Can I use a synthetic oil filter on my 2015 Wrangler?
Yes. Synthetic filters are designed to last longer and filter smaller particles than conventional filters, and they work fine on the 2015 Wrangler. They cost more upfront but may last through multiple oil changes if you're using synthetic oil. Check the filter's specifications to confirm it fits the M20 × 1.5 thread pitch.