Reset the oil change reminder after you change the oil yourself
The 2015 Jeep Grand Cherokee displays an oil change reminder on the instrument cluster when service is due. After you change the oil and filter, you need to manually reset this light — it does not clear on its own. The process takes less than a minute and requires only the ignition key; no tools or dealer visit needed.
The reset procedure differs slightly depending on whether your Grand Cherokee has a traditional instrument cluster or the newer Uconnect touchscreen display. Both methods are straightforward enough to do in your driveway while the engine is off.
Key Takeaways
- Turn the ignition to the "On" position without starting the engine to access the instrument cluster menu.
- Use the steering wheel buttons to navigate to the oil life menu and select the reset option.
- The light clears when ready after you confirm the reset; no restart or additional steps are required.
- If your Grand Cherokee has a Uconnect system, the reset path goes through the vehicle settings menu instead of the cluster buttons.
Reset on models with the standard instrument cluster
Sit in the driver's seat with the engine off and the ignition key in hand. Turn the key to the "On" position — the position where the dashboard lights up but the engine does not start. Do not turn the key all the way to "Start."
Look at the instrument cluster (the gauges and displays directly behind the steering wheel). You should see a small menu button or scroll wheel on the left side of the steering wheel. Press and hold this button until a menu appears on the cluster display. Navigate through the menu using the same button or the up and down arrows until you find "Oil Life" or "Service Oil."
Once you highlight the oil life option, press the button again to enter that submenu. You should see an option to reset or clear the service reminder. Select it, and the light will turn off when ready. Turn the ignition back to "Off" and you are finished.
Reset on models with Uconnect touchscreen
If your 2015 Grand Cherokee has the Uconnect infotainment system with a touchscreen in the center of the dashboard, the reset process uses that screen instead of the steering wheel buttons. Turn the ignition to "On" without starting the engine.
On the Uconnect screen, navigate to "Settings" or "Vehicle Settings" — the exact label depends on your software version. Look for a submenu labeled "Service" or "Maintenance." Tap on it and find the oil change reminder or oil life option. Select "Reset" or "Clear Service Reminder," and the message will disappear from both the touchscreen and the instrument cluster.
What happens if the reset does not work
If you follow the steps and the light remains on, the most common cause is that the ignition was not in the correct position. The system only responds when the key is in "On" — not "Accessory" and not "Start." Try again, making sure the dashboard is fully lit before you begin navigating the menu.
A second possibility is that you are looking at a different warning light. The oil change reminder is usually a wrench icon or the words "Service Oil" on the cluster display. If you see a red oil can icon instead, that indicates low oil pressure, which is a different problem that requires checking your oil level when ready and possibly stopping the engine.
If the light still will not clear after a second attempt, the cluster itself may have a fault. This is rare but does happen. A Jeep dealer can reset it using their diagnostic scanner, though this will cost you a service fee.
Resetting after a dealer oil change
If you had the oil changed at a Jeep dealership or independent shop, the technician should reset the light as part of the service. Ask them to confirm it is cleared before you leave. If you pick up your vehicle and the light is still on, call the shop and ask them to reset it — this takes them seconds and should be done at no charge since it is part of the oil change service.
Some independent shops may not be familiar with the 2015 Grand Cherokee reset procedure. If that happens, you can reset it yourself using the steps above, or ask the shop to show you how before you go.
Why the reminder system matters
The oil change reminder is based on engine hours and driving patterns, not just mileage. Resetting it after each oil change keeps the system accurate so you do not miss future service intervals. If you ignore the reminder and let it stay on, you may lose track of when your next oil change is actually due, which can lead to running too long on old oil.
The 2015 Grand Cherokee typically shows the reminder between 10,000 and 15,000 miles depending on driving conditions, though this varies. Resetting the light after every oil change — whether you do it yourself or have it done professionally — ensures the reminder stays useful as a maintenance tracker.
Frequently Asked Questions
Do I have to reset the light myself, or will it go away on its own?
The light will not clear on its own. It stays on until you manually reset it using the procedure above. The system does not know when you changed the oil unless you tell it by completing the reset.
What if I reset the light but have not actually changed the oil yet?
Resetting the light before an oil change will cause you to miss the next service interval. The reminder will not appear again until the system calculates that another 10,000 to 15,000 miles have passed. Only reset after the oil and filter are actually changed.
Can I reset the light with the engine running?
No. The reset only works when the ignition is in the "On" position with the engine off. If you start the engine, the menu will not appear or will not respond to your inputs.
Is there a way to reset the light from the Uconnect app on my phone?
The Uconnect mobile app on your phone does not include a reset function for the oil change reminder. You must use either the steering wheel buttons or the touchscreen in the vehicle itself.