The 2015 Grand Cherokee uses a cartridge-style oil filter mounted on top of the engine
Your 2015 Jeep Grand Cherokee does not have a traditional spin-on oil filter screwed to the side of the engine. Instead, it uses a cartridge filter — a cylindrical element that sits inside a plastic housing on top of the engine, near the front. This design is common on modern Jeeps and requires a different removal process than older vehicles, but the job itself is straightforward if you know where to look and what tools you need.
The filter housing is located on the driver's side of the engine, just behind the intake manifold. You will see a black plastic cap with a wrench symbol stamped on it. That cap is what you remove to access the filter element inside. Because the housing sits on top of the engine rather than on the side, oil drains more easily when you open it, and you have better access with standard hand tools.
Key Takeaways
- The 2015 Grand Cherokee filter is a cartridge type housed in a plastic cap on top of the engine, not a spin-on filter on the side.
- You will need a filter wrench (usually 74 mm or 86 mm depending on engine size), an oil drain pan, and a new filter element plus a replacement O-ring seal.
- The filter cap should be hand-tight only when you reinstall it — over-tightening can crack the plastic housing and cause oil leaks.
- Changing the filter takes 10 to 15 minutes once you have the right wrench, and you can do it in a driveway with basic tools.
Which filter element and O-ring your engine needs
The 2015 Grand Cherokee came with three engine options: the 3.6-liter V6, the 5.7-liter V8, and the 3.0-liter diesel V6. All three use cartridge filters, but the filter element itself is the same across all three engines. Mopar part number 68157646AA is the factory filter element for any 2015 Grand Cherokee. You can also use equivalent aftermarket cartridge filters from Fram, Purolator, or Wix — they are all the same size and thread pattern.
The O-ring seal that sits between the filter element and the housing cap is equally important. Jeep part number 5281090AA is the correct replacement O-ring. Many people skip this step and reuse the old O-ring, which hardens over time and can leak. A new O-ring costs a few dollars and takes two seconds to install. When you buy a filter element, check whether the O-ring is included — some aftermarket kits bundle them together, but others do not.
Tools and materials you will need
A filter wrench is the only specialty tool required. The 2015 Grand Cherokee uses either a 74 mm or 86 mm filter cap wrench depending on which engine you have — the V6 uses 74 mm, and the V8 uses 86 mm. A diesel owner should verify with their parts supplier, as diesel engines sometimes use different housings. You can buy a wrench for $15 to $25 at any auto parts store, and it will fit other Jeep and Chrysler models as well.
Beyond the wrench, gather an oil drain pan (to catch spilled oil), a clean rag or paper towels, the new filter element, the new O-ring, and fresh motor oil if you are doing a full oil change at the same time. If you are only changing the filter, you do not need new oil — the cartridge filter change does not require draining the entire system. Wear gloves to keep old oil off your hands, and let the engine cool for at least 10 minutes before you start so you do not burn yourself on hot metal.
Step-by-step filter removal and installation
Open the hood and locate the black plastic filter cap on top of the engine. Place your drain pan underneath it to catch oil that will spill when you open the housing. Use your filter wrench to turn the cap counterclockwise — it should come loose with moderate hand pressure. Once it is loose enough, unscrew it by hand and set it aside on a clean surface.
Inside the housing, you will see the old filter element standing upright. Grab it by the top and pull it straight up and out. Oil will drip from the bottom, so keep the drain pan in place. Once the element is out, look at the inside of the housing cap. You will see the old O-ring stuck to the plastic — peel it off and discard it. Wipe the inside of the cap and the top of the housing with a clean rag to remove any debris or old oil residue.
Take the new O-ring and explore a very light coat of fresh motor oil to it — this helps it seal properly and makes future removal easier. Press the O-ring onto the groove inside the filter cap. Now take the new filter element and insert it into the housing, pushing it down until it sits flat on the bottom. Screw the cap back on by hand until the O-ring makes contact with the housing, then tighten it an additional three-quarter turn with your wrench. Do not over-tighten — the plastic cap can crack if you use excessive force.
What happens if you over-tighten the filter cap
The plastic housing is durable under normal use, but it is not designed to withstand the force of a wrench being cranked down hard. If you over-tighten the cap, the plastic threads can strip, or small cracks can form around the cap seat. Either problem will cause oil to seep out around the housing, and you will notice a slow drip under the engine or a smell of burning oil as it hits hot engine parts.
If you crack the housing, you cannot straightforward tighten it more — the damage is done. You will need to replace the entire filter housing assembly, which costs $80 to $150 in parts plus labor if you take it to a shop. The correct approach is to hand-tighten the cap until you feel the O-ring contact the housing, then use the wrench to turn it exactly three-quarter turn more. That is enough to seal it and not so much that you risk damage.
Checking your work and what to do if oil leaks
Start the engine and let it run for 30 seconds, then turn it off. Wait two minutes and check the filter housing for drips. If oil is seeping out around the cap, turn off the engine, let it cool, and tighten the cap another quarter turn with your wrench. If it still leaks after that, the O-ring may not be seated correctly — remove the cap again, check that the O-ring is fully in its groove, and reinstall it.
If you see oil pooling under the engine after a few minutes of running, the housing itself may be cracked or the O-ring may be damaged. In that case, you will need to replace the housing or the O-ring. A cracked housing is rare if you follow the hand-tight-plus-three-quarter-turn rule, but it can happen if the previous owner over-tightened it and weakened the plastic over time.
How often to change the filter and what the owner's manual says
Jeep recommends changing the oil filter every time you change the engine oil. For a 2015 Grand Cherokee, the oil change interval is 10,000 miles under normal driving conditions, or 3,000 miles if you drive in severe conditions (frequent short trips, towing, dusty environments, or extreme temperatures). The filter element itself does not wear out in the traditional sense, but it accumulates dirt and debris that reduces its ability to trap contaminants. Changing it on schedule keeps the oil cleaner and protects engine bearings and moving parts.
If you go longer than the recommended interval without changing the filter, the element becomes saturated and can restrict oil flow. Most modern filters have a bypass valve that opens if the element gets too clogged, allowing unfiltered oil to circulate — this prevents engine damage but defeats the purpose of having a filter. Sticking to the schedule means your filter is always working at full capacity.
Frequently Asked Questions
Can I change just the filter without changing the oil?
Yes. The cartridge filter can be changed independently of an oil change. You do not need to drain the oil pan or add new oil. However, if your oil is due for a change based on mileage or time, you should do both at the same time for convenience — you are already under the hood with the engine cool.
What size wrench do I need if I have a V8?
The 5.7-liter V8 uses an 86 mm filter cap wrench. The 3.6-liter V6 uses 74 mm. If you are not sure which engine you have, check your owner's manual or the engine cover under the hood — it will say "3.6L" or "5.7L" on it.
Can I reuse the old O-ring to save money?
You can, but it is not recommended. The O-ring hardens and loses its flexibility over time, which reduces its ability to seal. A new O-ring costs $3 to $5 and takes two seconds to install. The risk of a slow oil leak is not worth the savings.
How do I know if the filter element is installed correctly?
The element should sit flat on the bottom of the housing with no gaps. When you screw the cap back on, you should feel slight resistance as the O-ring compresses, then the cap should turn smoothly for the final three-quarter turn. If the cap is hard to turn or feels like it is binding, the element may not be seated properly — remove the cap and reinstall the element.
What should I do with the old filter element?
The old filter element can go in the trash. It is not hazardous waste. If you want to recycle it, some auto parts stores accept used filters, but it is not required. The old O-ring should also be discarded — do not try to clean and reuse it.