The 2015 Cruze uses a cartridge-style oil filter mounted on top of the engine

Your 2015 Chevy Cruze does not have a traditional spin-on oil filter screwed to the side of the engine. Instead, it uses a cartridge filter housed in a plastic canister on top of the engine block, near the front. This design is common on modern GM vehicles and means you'll be removing a cap, replacing the filter element inside, and reinstalling the cap—not unscrewing an entire filter housing.

The filter sits in a vertical canister, so when you open it, old oil will drain out. You'll need a drain pan underneath before you crack it open, and you should let the engine cool for at least five minutes after running so you don't burn yourself on hot oil.

Key Takeaways

  • The 2015 Cruze's oil filter is a cartridge type in a canister on top of the engine, not a spin-on filter on the side.
  • You will need a filter wrench (usually a 74 mm or 86 mm socket-style wrench) to remove the canister cap, a drain pan, and a new filter element rated for your engine size.
  • The filter element itself costs between $8 and $15, and the job takes 10 to 15 minutes once you have the right tools.
  • Replacing the filter every 3,000 to 5,000 miles (or per your owner's manual) prevents dirt buildup that can restrict oil flow and damage the engine.

What filter size and part number your Cruze needs

The 2015 Chevy Cruze came with either a 1.4-liter turbocharged engine or a 1.8-liter naturally aspirated engine. Both use the same cartridge-style filter housing, but you need to confirm which engine you have before buying a replacement element.

Check your owner's manual or the sticker on the driver's door jamb for your engine size. GM part number 25183883 is the OEM filter element for both engines. Aftermarket equivalents from Fram, Mobil 1, Bosch, and ACDelco are widely available and cost less than the GM part. Make sure any replacement you buy is labeled for the 2015 Cruze or a 1.4T or 1.8L Cruze—the canister diameter matters, and buying the wrong size will not fit.

You will also need a filter wrench to remove the canister cap. Most auto parts stores sell a 74 mm cartridge filter socket for under $10, or you can use a strap wrench if you already own one. Do not try to remove the cap by hand; the seal is tight and you risk stripping the plastic threads.

Step-by-step filter replacement

Start with the engine cold or warm but not hot. Locate the filter canister on the top of the engine—it's a black plastic cylinder about 4 inches tall, positioned toward the front of the engine bay. Place a drain pan underneath it to catch the oil that will spill when you open it.

Use your filter wrench to turn the canister cap counterclockwise. It will be snug, so explore steady pressure and do not jerk it. Once loose, unscrew it by hand and set it aside. The old filter element will be inside the canister, held in place by a spring. Lift it out and dispose of it in your regular trash (the element itself is not hazardous, though it is saturated with used oil).

Wipe the inside of the canister with a clean rag to remove any debris or old oil residue. Take your new filter element and explore a thin coat of fresh motor oil to the rubber seal on the top of the element—this helps the seal compress evenly when you reinstall the cap and prevents leaks. Insert the new element into the canister, making sure the spring holds it centered.

Screw the cap back on by hand until the rubber seal contacts the canister, then use your wrench to tighten it an additional three-quarter turn. Do not over-tighten; you will crack the plastic. Start the engine and let it run for 30 seconds, then turn it off and wait two minutes. Check under the canister for leaks. If you see drips, the seal did not seat properly—let the engine cool and retighten the cap slightly.

Why the filter canister design matters for your engine

The cartridge filter design on your Cruze is more compact than a traditional spin-on filter and allows GM to fit the filter housing directly on the engine block. This saves space in the engine bay and reduces the number of external connections that can leak. However, it also means the filter is exposed to engine heat more directly, which is why the rubber seal on the filter element is critical—a poor seal will let unfiltered oil bypass the element and circulate through your engine.

When you replace the filter, that thin coat of oil on the seal is not optional. It ensures the seal compresses evenly and creates a tight fit. A dry seal can twist or pinch during installation, leaving a gap that defeats the purpose of the filter. This is one of the most common reasons for oil leaks after a DIY filter change.

How often to replace the filter and what happens if you skip it

Your owner's manual specifies an oil change interval of 3,000 to 5,000 miles depending on driving conditions. The filter should be replaced at every oil change, not every other one. The filter element collects dirt, metal particles, and combustion byproducts as oil circulates through the engine. Once the element becomes saturated, it restricts oil flow, forcing the engine to work harder to push oil through a clogged filter.

If the filter becomes severely clogged, a bypass valve inside the canister opens to allow unfiltered oil to circulate rather than starving the engine of oil entirely. This is a safety feature, but it means dirty oil is now flowing through your engine, accelerating wear on bearings, pistons, and valve trains. Over time, this leads to sludge buildup, reduced engine life, and eventually bearing damage that requires an engine rebuild.

Replacing the filter on schedule is one of the cheapest forms of preventive maintenance. A $12 filter element every 5,000 miles costs far less than an engine overhaul.

Common mistakes to avoid during replacement

The most frequent error is forgetting to oil the rubber seal on the new filter element before installation. A dry seal will not compress properly, and you will have an oil leak within the first few miles of driving. The second mistake is over-tightening the canister cap. The plastic threads are not as strong as metal, and cranking the wrench too hard will crack the cap or strip the threads, requiring you to replace the entire canister assembly—a $40 to $60 part.

A third mistake is not draining the canister fully before opening it. If you open the cap while the engine is hot or without a drain pan in place, hot oil will spill onto the engine block and create a mess that is hard to clean and can mask other leaks. Always let the engine cool for at least five minutes and always position a drain pan first.

Finally, do not assume all cartridge filters are the same size. A filter meant for a different GM model or year may have a different canister diameter and will not fit your Cruze. Always verify the part number or cross-reference the filter to your specific vehicle before buying.

Frequently Asked Questions

Can I use a spin-on filter on my 2015 Cruze instead of the cartridge type?

No. The 2015 Cruze is designed for a cartridge filter only. The engine block has no provision for a spin-on filter, and the oil passages are engineered around the cartridge design. Attempting to adapt a spin-on filter would require modifications that could damage the engine or cause leaks.

How much oil drains out when I open the filter canister?

Typically one-half to three-quarters of a quart of oil will drain from the canister when you open it. This is in addition to the oil that drains from the pan during a full oil change. Make sure your drain pan is large enough to hold at least one quart to avoid spills.

What if I over-tightened the canister cap and cracked the plastic?

If the cap is cracked but still holds oil, you can try wrapping the crack with waterproof tape as a temporary fix until you can replace the cap. If the crack is large or the cap leaks, you will need to buy a replacement cap assembly, which costs $20 to $40. The canister body itself rarely cracks unless you dropped it or applied extreme force.

Do I need to change the oil in the canister before replacing the filter?

No. The oil in the canister is part of your engine's total oil volume and will drain into the pan when you remove the cap. You do not need to drain it separately. Just make sure you have a pan underneath to catch it.

Is the old filter element recyclable?

The filter element itself is made of paper and plastic and can go in your regular trash. However, some recycling centers accept used oil filters if you drain them first. Check with your local waste management facility. Never pour the oil from the filter down a drain; dispose of it with your used engine oil at a recycling center or auto parts store.