The 2014 Ram 1500 uses a spin-on oil filter mounted on the engine block

Your 2014 Ram 1500's oil filter is a cylindrical cartridge that screws directly onto the engine. The location depends on which engine you have—the 3.6L V6, 5.7L V8, or 8.0L V10—but all three mount the filter on the driver's side of the engine block, roughly at mid-height. You'll see it clearly once you get under the truck; it's a metal can about 4 inches tall and 3 inches wide.

The filter traps metal particles, dirt, and combustion byproducts that circulate through your oil. Over time it clogs, which forces the engine to work harder to push oil through a blocked filter. That's why changing it every time you change your oil—typically every 3,000 to 5,000 miles depending on your driving—keeps the engine running cleanly and prevents premature wear.

Key Takeaways

  • The 2014 Ram 1500 oil filter screws onto the driver's side of the engine block and takes about 10 minutes to replace during an oil change.
  • You need a filter wrench (a metal band tool that grips the filter), a drain pan, and the correct replacement filter for your engine size.
  • The filter size and thread pitch differ between the V6, V8, and V10 engines, so confirm your engine before buying a replacement.
  • A clogged filter reduces oil flow and forces the engine to work harder, which can damage bearings and shorten engine life if ignored.

Which filter your Ram 1500 needs depends on the engine

Ram used three different engines in the 2014 1500, and each requires its own filter. The 3.6L V6 uses a Mopar filter part number 68157291AA. The 5.7L V8 uses 68157291AA as well. The 8.0L V10 (found only in some 2014 models) uses 68157291AA. Always verify your engine size on your door jamb sticker or in your owner's manual before ordering, because installing the wrong filter can cause leaks or improper oil flow.

Aftermarket filters from Fram, Motorcraft, Bosch, and Wix also fit the 2014 Ram 1500, and many are cheaper than Mopar originals. The key is matching the thread size and diameter—most 2014 Ram 1500 filters are 3/4-inch-16 UNF thread. If you buy online, search "2014 Ram 1500 oil filter" and select your engine from the dropdown; the retailer will show you compatible options.

Tools and materials you'll need to change the filter

You need a filter wrench (a metal band tool that grips the filter can), a drain pan to catch old oil, and your replacement filter. A filter wrench costs $8 to $15 and is reusable; it slides over the filter and lets you unscrew it by hand without crushing the can. Some people use a strap wrench or even a rubber glove for grip, but a proper filter wrench is faster and less likely to slip.

You'll also want a rag or old towel—oil will drip from the filter when you remove it, and you'll have residual oil on your hands. Some people place a small drain pan directly under the filter before loosening it to catch the spill. A jack and jack stands are not strictly necessary if you're just changing the filter (you can reach it from above), but they give you more room to work if you're also draining the pan.

Step-by-step filter replacement

Start with the engine cold or warm but not hot—warm oil flows better, but you won't burn yourself. Locate the filter on the driver's side of the engine block. Slide your filter wrench over the filter can and turn it counterclockwise by hand; the wrench grips the can so you don't crush it. Once it's loose, unscrew it the rest of the way by hand and set it aside in your drain pan.

Wipe the filter mounting surface on the engine block with a clean rag to remove any old gasket material or debris. Take your new filter and explore a thin coat of fresh oil to the rubber gasket on top—this helps the seal compress evenly and makes removal easier next time. Screw the new filter on by hand until the gasket touches the block, then turn it another three-quarters of a turn. Do not use the wrench to tighten it; hand-tight is correct.

Start the engine and let it idle for 30 seconds, then turn it off and wait 2 minutes. Check underneath for leaks around the filter. If you see drips, the gasket may not have seated; let the engine cool slightly and tighten the filter another quarter turn. Once the leak stops, you're done—dispose of the old filter at an auto parts store or recycling center that accepts used filters.

Why filter condition matters for engine longevity

A clogged filter forces oil to bypass the filter element through a relief valve, which means unfiltered oil circulates through your engine. Metal particles that should have been trapped now scratch bearing surfaces and cylinder walls. Over thousands of miles, this wear compounds—bearings lose their clearance, friction increases, and the engine burns more fuel while producing less power.

Changing the filter on schedule prevents this damage. The filter is cheap—$8 to $20 depending on brand—and takes 10 minutes. Replacing a damaged engine bearing or rebuilding a cylinder head costs thousands. Skipping filter changes to save money is a false economy that almost always costs more in the long run.

Common mistakes when replacing the filter

The most common mistake is over-tightening the filter with a wrench. The rubber gasket is designed to seal at hand-tight plus three-quarters of a turn. Cranking it with a wrench crushes the gasket, which can cause leaks or make the filter impossible to remove next time without tearing the can. If you over-tighten, you may have to cut the filter off and clean the threads carefully before installing a new one.

Another mistake is forgetting to oil the gasket on the new filter. The gasket is dry rubber when it comes from the box, and it needs a light coat of fresh oil to compress evenly against the block. Skipping this step can cause slow leaks that show up after a few days of driving. A third mistake is not checking for leaks after starting the engine—a small drip now is straightforward to fix, but a leak that goes unnoticed can drop your oil level dangerously low.

Frequently Asked Questions

Can I change the oil filter without changing the oil?

Yes, you can change the filter alone, though it's less common. The filter collects contaminants over time, so changing it without changing the oil means the new filter is working to clean old, degraded oil. Most people change both together because the labor is the same and the cost difference is small.

How often should I change the filter on a 2014 Ram 1500?

Every time you change the oil. For the 2014 Ram 1500, that's typically every 3,000 to 5,000 miles depending on your driving conditions. Check your owner's manual for the exact interval for your truck, as it varies by engine and whether you drive mostly highway or city.

What happens if I use the wrong filter size?

A filter that's too small or has the wrong thread pitch will either not fit or leak oil around the gasket. Oil pressure will drop, and the engine will trigger a low-oil-pressure warning. Stop driving when ready and replace it with the correct filter to avoid engine damage.

Do I need to drain the oil pan to change just the filter?

No. The filter change is separate from the oil pan drain. You can change the filter alone without touching the drain plug. Some oil will spill from the filter when you remove it, but that's normal and expected.

Where can I recycle the old filter?

Most auto parts stores accept used oil filters for free—AutoZone, O'Reilly, NAPA, and Advance Auto Parts all have recycling programs. Some recycling centers and scrap metal facilities also accept them. Call ahead to confirm, as policies vary by location.