The 2014 Grand Cherokee uses a cartridge-style filter mounted on top of the engine

The 2014 Jeep Grand Cherokee does not have a traditional spin-on oil filter screwed to the side of the engine. Instead, it uses a cartridge filter housed in a plastic cap on top of the engine block. This design is common on modern Jeeps and requires a different removal process than older vehicles. The filter sits under a black plastic cover labeled with an oil can symbol, located toward the rear of the engine bay on the driver's side.

Knowing this matters because you cannot straightforward unscrew a filter like you would on many other vehicles. You need to remove the entire cap assembly, replace the filter element inside, and reinstall it. The job takes about 15 to 20 minutes once you have the right tools and filter on hand.

Key Takeaways

  • The 2014 Grand Cherokee has a cartridge filter under a plastic cap on top of the engine, not a spin-on filter on the side.
  • You will need an oil filter socket (usually 74mm or 76mm) to remove the cap, plus a new filter element and a new rubber seal.
  • The correct replacement filter part number is Mopar 68157291AA or equivalent aftermarket cartridge filters rated for the 3.6L or diesel engines.
  • Always replace the rubber seal on the cap when you replace the filter; reusing the old seal often causes oil leaks.
  • Drain the oil first, then remove the filter cap, swap the filter element and seal, and reinstall the cap with hand-tight pressure only.

What filter size and part number you need

The Mopar part number 68157291AA is the factory filter element for the 2014 Grand Cherokee with the 3.6L V6 gasoline engine, which is the most common powertrain. If your vehicle has the 5.7L V8 or the 3.0L diesel, confirm the part number with your dealer or filter supplier, as some diesel models use a different element. Aftermarket brands like Fram, Motorcraft, and Bosch make equivalent cartridge filters; look for filters labeled as fitting the 2014 Grand Cherokee or filters with a 74mm or 76mm cap diameter.

Do not rely on filter size alone to order online. Always cross-reference the part number or vehicle year and engine size. Ordering the wrong filter can result in a poor seal or a filter that does not fit the cap at all. You also need a replacement rubber seal (O-ring) that sits between the filter cap and the engine block. Mopar part number 68157291AB is the seal; many filter kits include it, but some do not, so check before you buy.

Tools and materials you will need

Gather these items before you start: an oil filter socket (74mm or 76mm, depending on your engine), a ratchet wrench, a drain pan, jack stands or ramps (to safely raise the vehicle if needed), new oil, an oil drain plug gasket if your vehicle uses one, and the replacement filter element and seal. A socket wrench set with a 13mm socket will fit the drain plug on most 2014 Grand Cherokees.

The oil filter socket is the most important tool. It is a large socket with notches or a band that grips the plastic cap. You can rent one from an auto parts store for a few dollars if you do not own one. Do not attempt to remove the cap by hand or with a strap wrench; you risk cracking the plastic. An oil catch pan is essential to avoid spilling oil on the engine or ground.

Step-by-step removal and replacement

Step 1: Drain the oil. Warm the engine by running it for a minute or two, then turn it off and wait five minutes. Locate the drain plug on the underside of the engine pan (you may need to raise the vehicle safely with jack stands). Loosen the plug with a 13mm wrench, unscrew it by hand, and let the old oil drain into the pan. Once the flow slows, wipe the plug and the surrounding area clean.

Step 2: Remove the filter cap. Open the hood and locate the black plastic cap on top of the engine. Place your oil catch pan underneath it to catch any remaining oil. Fit the oil filter socket over the cap and attach it to a ratchet. Turn counterclockwise to loosen the cap. Once loose, unscrew it by hand and lift it straight up. Oil will drip, so keep the pan in place.

Step 3: Remove the old filter element and seal. Inside the cap, you will see a cylindrical filter element and a rubber seal on the underside of the cap. Pull the filter element out and discard it. Peel off the old rubber seal and clean the cap and the mating surface on the engine block with a clean rag. Do not leave any debris or old seal material behind.

Step 4: Install the new seal and filter. Press the new rubber seal onto the underside of the cap, making sure it sits evenly all the way around. Insert the new filter element into the cap, pushing it in until it seats fully. The filter should not rattle or move inside the cap.

Step 5: Reinstall the cap. Align the cap with the opening on the engine block and thread it on by hand. Once hand-tight, use the filter socket and ratchet to snug it down. Do not over-tighten; hand-tight plus a quarter turn is sufficient. Over-tightening can crack the plastic cap or damage the seal.

Step 6: Reinstall the drain plug. Wipe the drain plug clean and install a new crush washer or gasket if your vehicle uses one (most 2014 models do). Thread the plug in by hand, then tighten it with a wrench to about 25 foot-pounds of torque. If you do not have a torque wrench, snug it firmly but do not force it.

Step 7: Add new oil and check the level. Pour the recommended amount of new oil into the filler cap on top of the engine. The 2014 Grand Cherokee typically holds 5 to 6 quarts depending on the engine; check your owner's manual or the oil cap for the exact amount. Start the engine and let it run for a few seconds, then turn it off and wait a minute. Check the oil level on the dipstick or digital display and top off if needed.

Common mistakes to avoid

The most frequent error is reusing the old rubber seal. Even if it looks intact, the seal loses its flexibility over time and will not create a watertight fit. A leaking seal leads to oil seeping around the cap and onto the engine. Always install a new seal with every filter change. The second mistake is over-tightening the cap. The plastic threads are not as strong as metal, and forcing the cap down can strip them or crack the cap itself. Hand-tight plus a small amount of additional pressure is all you need.

Another common issue is installing the wrong filter element. If the filter does not slide smoothly into the cap or feels loose, stop and double-check the part number. Forcing a wrong filter into the cap can damage the internal sealing surfaces. Finally, do not forget to reinstall the drain plug after draining the oil. It is straightforward to get focused on the filter and leave the drain plug sitting on the ground.

When to replace the oil filter

Jeep recommends changing the oil and filter every 10,000 miles under normal driving conditions, or every 3 months, whichever comes first. If you drive in severe conditions—towing, frequent short trips, dusty environments, or extreme temperatures—change the filter every 5,000 miles or 3 months. Check your owner's manual for the exact interval for your driving situation. The filter element itself does not wear out like a spark plug; it straightforward becomes saturated with contaminants and loses its ability to trap particles.

If you notice the oil pressure warning light on the dashboard, do not ignore it. Low oil pressure can indicate a clogged filter, low oil level, or an engine problem. Check the oil level first and inspect the filter cap for leaks. If the seal is leaking or the filter is visibly dirty, replace it when ready even if you are not at the scheduled interval.

Frequently Asked Questions

Can I change the oil filter without draining the oil first?

Technically yes, but it is not recommended. Some oil will spill when you remove the cap, and you will have a mess. If you are only changing the filter and not the oil, you can skip draining the engine oil itself, but expect a small amount to drip from the filter cap area. Have your catch pan ready and be prepared to clean up.

What happens if I over-tighten the filter cap?

Over-tightening can crack the plastic cap or strip the threads on the engine block, leading to oil leaks that are expensive to repair. It can also damage the rubber seal, causing it to fail when ready. Tighten only until snug; you should not need a wrench to remove it next time.

Is the 2014 Grand Cherokee filter the same as other Jeep models?

No. The filter element and cap design vary by engine size and model year. A 2014 Grand Cherokee filter will not fit a 2011 model or a 2014 Wrangler. Always verify the part number for your specific vehicle before ordering. Using the wrong filter can result in a poor seal or a filter that does not fit.

Do I need to reset anything after changing the oil filter?

The 2014 Grand Cherokee does not require a reset after an oil filter change. Some models have an oil change reminder that you can reset through the dashboard menu, but this is optional and does not affect engine performance. Consult your owner's manual if you want to clear the reminder.

Where can I buy the correct filter and seal?

Auto parts stores like AutoZone, O'Reilly, NAPA, and Advance Auto Parts stock cartridge filters for the 2014 Grand Cherokee. Dealerships carry the Mopar part number. Online retailers like Amazon and RockAuto also sell them. Bring your vehicle year, make, model, and engine size to may support you get the right part, or order using the Mopar part number 68157291AA.