The 2014 Ford Focus uses a cartridge-style oil filter mounted on top of the engine
The 2014 Ford Focus has a cartridge oil filter — a cylindrical canister that screws into the top of the engine rather than a spin-on filter that hangs from the side. This design is common on Ford vehicles and sits directly above the engine block. You'll find it under the hood, toward the front-center of the engine, inside a plastic housing cap.
The filter element itself is a replaceable paper cartridge inside that housing. When you change the oil, you remove the cap, pull out the old cartridge, and install a new one. This is different from older vehicles where you unscrew the entire filter canister — here, only the internal element comes out.
Key Takeaways
- The 2014 Ford Focus oil filter is a cartridge style located under a plastic cap on top of the engine, not a spin-on filter on the side.
- You will need a cartridge-style replacement filter, an oil filter wrench or cap socket (usually 86 mm), and new rubber seals that come with the replacement cartridge.
- The filter housing cap requires hand-tightening only — over-tightening can crack the plastic housing and cause oil leaks.
- Changing the cartridge takes about 10 to 15 minutes once you have the right tools and a safe way to access the top of the engine.
What filter type and part number fit a 2014 Ford Focus
Ford part number CV6Z-6714-B is the OEM (original equipment manufacturer) cartridge filter for the 2014 Focus with a 2.0L EcoBoost engine. If your Focus has the 2.0L naturally aspirated engine, the part number is CV6Z-6714-A. Both are cartridge-style filters, not spin-on types.
Aftermarket filters that fit the 2014 Focus include Motorcraft FL-910S, Fram CH10165, and Bosch 3330. Any cartridge filter designed for a 2014 Ford Focus will work, but verify the part number matches your engine size before purchase. The filter housing cap is the same across both engine options, so the difference is only in the cartridge element itself.
When you buy a replacement cartridge, it usually comes with two rubber seals — one for the top of the cartridge and one for the bottom. These seals are critical: a dry or damaged seal will cause oil to leak around the housing cap. Do not reuse old seals.
Tools and supplies you will need
You need an 86 mm oil filter cap socket or a cartridge-style oil filter wrench to remove the plastic housing cap. A standard wrench will not fit because the cap is round and smooth. You can buy a cap socket at any auto parts store for $10 to $20, or rent one from some stores. A socket wrench handle (usually 3/8-inch drive) attaches to the cap socket.
Have the new cartridge filter, fresh engine oil, and an oil drain pan ready. A clean rag or paper towels help you wipe the housing and seals. If you are draining the oil at the same time, you will also need a wrench to remove the drain plug — usually a 13 mm or 15 mm socket.
You do not need a lift or jack if you can safely access the top of the engine from the side of the vehicle. The filter housing sits high enough that most people can reach it without raising the car, though a small step stool may help.
Step-by-step filter replacement
Step 1: Warm the engine slightly. Run the engine for 30 seconds to a minute so the oil flows more easily. Turn it off and wait two minutes before opening the hood — hot oil can burn you.
Step 2: Locate and remove the housing cap. Open the hood and find the cylindrical plastic cap on top of the engine, toward the front-center. Place your oil drain pan underneath it to catch any spilled oil. Fit the 86 mm cap socket over the cap and turn it counterclockwise with a socket wrench. The cap will unscrew and lift away.
Step 3: Remove the old cartridge. Inside the housing, you will see the cylindrical cartridge filter. Lift it straight up and out. Some oil will drip, so keep the pan in place. Wipe the inside of the housing with a clean rag to remove any debris or old seal material.
Step 4: Install the new cartridge. Take the new cartridge and check that both rubber seals are in place — one on the top and one on the bottom. Slide the cartridge straight down into the housing until it seats. It should fit snugly but not require force.
Step 5: Replace the housing cap. Fit the plastic cap back over the cartridge opening. By hand, screw it clockwise until the rubber seal on the cap contacts the top of the cartridge. Then use the cap socket to tighten it an additional one-quarter to one-half turn. Do not over-tighten — the plastic housing can crack if you force it.
Step 6: Check for leaks. Start the engine and let it run for 30 seconds. Turn it off and wait one minute, then look under the housing cap for drips. If oil is leaking around the cap, the seal may not be seated correctly. Turn off the engine, remove the cap, and reseat the cartridge.
Common mistakes to avoid
The most common error is over-tightening the housing cap. The plastic cap is not meant to be cranked down hard — hand-tight plus a quarter turn is the correct torque. Forcing it will crack the housing and cause an oil leak that requires replacing the entire housing assembly, not just the cap.
Another mistake is installing the cartridge upside down or not seating it fully. The cartridge should slide straight down and sit flat inside the housing. If it feels stuck or crooked, remove it and check that the seals are not twisted or folded.
Do not reuse the old rubber seals. They compress and harden over time and will not seal properly a second time. New seals come with the replacement cartridge — use them every time.
When to change the oil filter
Ford recommends changing the oil filter every time you change the engine oil. For a 2014 Focus, that interval is typically every 10,000 miles or 12 months, whichever comes first, if you use synthetic oil. With conventional oil, the interval may be shorter — check your owner's manual for the exact schedule based on your driving conditions.
If you drive in severe conditions (towing, frequent idling, dusty roads, or short trips), the interval may be shorter. Your owner's manual will specify a severe-service schedule. Changing the filter at the same time as the oil ensures you are removing old filter media that has collected contaminants.
Frequently Asked Questions
Can I change just the oil filter without draining the oil?
Yes. The filter and oil drain are separate tasks. You can change the filter alone, though most people do both at the same time since you are already under the hood. Changing the filter without draining the oil takes about 10 minutes.
What happens if I over-tighten the housing cap?
The plastic housing can crack, causing oil to leak around the cap. If this happens, you will need to replace the entire housing assembly, not just the cap. Hand-tight plus a quarter turn is the correct amount — do not use a wrench to force it.
Where do I dispose of the old oil filter?
Most auto parts stores accept used oil filters for free. Some recycling centers also take them. Do not throw it in the trash — the filter contains used oil and is recyclable. Call your local waste management or check an auto parts store for drop-off locations.
Is the 86 mm cap socket the only tool that works?
An 86 mm cap socket is the standard tool, but some cartridge-style filter wrenches also fit. A regular wrench will not work because the cap is smooth and round. If you do not have the socket, you can rent one from an auto parts store or borrow one from a friend.
Do I need to fill the new filter with oil before installing it?
No. Unlike spin-on filters, cartridge filters do not need to be pre-filled. straightforward install the dry cartridge with the new seals in place, and the oil will flow through it once the engine starts.